Emerson CF930BS00 User manual

Part No. F40BP73320000 Form No. BP7332
UL Model No.: CF930
READ AND SAVE THESE INSTRUCTIONS
Net Weight: 18.0 Lbs.
ATOMICAL™
52” Damp Location
Ceiling Fan
Owner's Manual
CF930BS00
CF930ORB00
CF930WW00
Model No.
INSTRUCTION TO THE USER
(if device contains a digital device)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user is
cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
BP7332 CF930 10/27/06 10:05 AM Page 1

WARNING: To avoid fire, shock, and serious personal injury, follow these
instructions. Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service
panel disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Always turn off the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before
wiring, and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA
70-1999 and Local Codes. Use the National Electrical Code if Local Codes do not
exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably
supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for
Fan Support”, and use the mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to
fan blade clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent
accidental contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling
fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used
with fan speed control Model No. UC7067RC, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this
product and/or any accessories designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with
this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when
installing the blade flanges, balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electric shock, this fan must be installed with an
isolating wall control/switch.
!WARNING
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
BP7332 CF930 10/27/06 10:05 AM Page 2

3
THIS FAN IS SUITABLE FOR DAMP LOCATIONS
SUCH AS COVERED PORCHES, COVERED PATIOS, AND COVERED
DECKS...ANYWHERE THERE IS A ROOF OVERHEAD.
This Manual is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Do not install or use fan if any part is
damaged or missing. Call Toll-Free:
1-800-654-3545
!WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
!WARNING
Tools Needed for Assembly
One Phillips head screwdriver
One wire stripper
One stepladder
Two 60-watt (maximum) candelabra
base bulbs
Materials
Wiring, outlet box and box connectors
must be of type required by the local code.
The minimum wire would be a 3-conductor
(2-wire with ground) of the following sizes:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Before assembling your ceiling fan, refer
to section on proper method of wiring
your fan (Page 9). If you feel you do not
have enough wiring knowledge or
experience, have your fan installed by a
licensed electrician.
!WARNING
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.
NOTE: If you are uncertain of part
description, refer to exploded view
illustration.
a. Fan motor assembly
b. One coupling cover
c. One ceiling cover
d. Five fan blades
e. One lower housing
f. One light kit assembly
g. One hanger bracket
h. One hanger ball/4.5” downrod assembly
i. One lower glass
j. One fan/light wall control
(transmitter and receiver)
k. One loose parts bag containing:
1. One clevis pin
2. One hairpin clip
3. Three 12 ga. wire connectors
4. Four 18 ga. wire connectors
5. Two #8-32 x 1-1/4” threaded studs
6. Two #8 external tooth lockwashers
7. Two #8-32 knurled knobs
8. Sixteen M5 x 12mm washer head
screws
9. Seven M4 x 10mm serrated head
screws
10. One balancing kit
1. Open carton containing fan. Remove
top half of styrofoam unit. Remove
parts and check to see that you have
received the following parts:
BP7332 CF930 10/27/06 10:05 AM Page 3

4
2. Remove and discard the two cardboard
shipping retainers securing the motor
hub in the motor housing assembly.
3. Remove the fan motor assembly from
the protective plastic bag. Place all
carton contents on a protective surface.
A. FAN MOTOR ASSEMBLY
B. COUPLING COVER
C. CEILING COVER
D. FAN BLADES E. LOWER HOUSING
F. LIGHT KIT ASSEMBLY
EMERSON
®
HI
MED
LOW
FAN OFF
LIGHT
ONOFF
J. FAN/LIGHT WALL CONTROL
G. HANGER BRACKET H. HANGER BALL/
4.5" DOWNROD
ASSEMBLY
K. LOOSE
PARTS BAG
I. LOWER GLASS
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost.
IMPORTANT
IMPORTANT
CARDBOARD
SHIPPING RETAINER (2)
PROTECTIVE
PLASTIC BAG
BP7332 CF930 10/27/06 10:05 AM Page 4

5
Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.
General
Your Emerson ceiling fan comes supplied
with a Fan/Light Wall Control which
consists of a wall control (transmitter) and
a remote control receiver mounted under
the ceiling cover. This system allows you
to regulate your ceiling fan speed and light
intensity.
NOTE: An optional Emerson Electric
SR100 Remote Control may also be
used to control your ceiling fan.
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
!WARNING
If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.
IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric Fan/Light Wall
Control supplied with the fan, or an
optional Emerson Electric SR100
Remote Control.
Electrical Requirements Ceiling Fan Procedures
IMPORTANT: Before assembling your
ceiling fan, refer to sections “Setting
Operating Frequency of Wall Control
and Receiver” and “Installation of Wall
Control”, Page 12. These sections
instruct you how to: a) Set the
operating frequency of the fan/light
wall control and the remote control
receiver; and b) Install the fan/light wall
control in the wall box. You will then be
ready to proceed with the assembly
and installation of your ceiling fan, as
follows:
How to Assemble Your
Ceiling Fan
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
!WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
!WARNING
BP7332 CF930 10/27/06 10:05 AM Page 5

6
1. Remove the hanger ball by loosening
the setscrew in the hanger ball until the
ball falls freely down the downrod
(Figure 1). Remove the clevis pin from
the downrod, then remove the hanger
ball. Retain the pin and hanger ball for
reinstallation in step 5.
2. Loosen setscrew in motor coupling if
necessary. Separate, untwist and
unkink the three 80” motor leads. Route
the motor lead wires through the
downrod. Align the clevis pin holes in
the downrod with the holes in the motor
coupling. Install the clevis pin and
secure with the hairpin clip (Figure 2).
The clevis pin must go through the
holes in the motor coupling and the
holes in the downrod. Be sure to push
the straight leg of the hairpin clip
through the hole near the end of the
clevis pin until the curved portion of the
hairpin clip snaps around the clevis pin.
The hairpin clip must be properly
installed to prevent the clevis pin from
working loose. Pull on the downrod to
make sure the clevis pin is properly
installed.
PIN
HANGER
BALL
SETSCREW
DOWNROD
Figure 1
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
DOWNROD
HAIRPIN CLIP
MOTOR
COUPLING
SETSCREW (2)
CLEVIS PIN
Figure 2
HAIRPIN
CLIP
CLEVIS PIN
MOTOR
COUPLING
COUPLER
COVER
CEILING
CANOPY
SETSCREW (2)
Figure 3
It is critical that the clevis pin in the motor
coupling is properly installed and the
setscrew securely tightened. Failure to
verify that the pin and setscrew are
properly installed (as shown in Figure 2)
could result in the fan falling.
!WARNING
3. While pulling up on the downrod,
securely tighten the two setscrews in
the motor coupling (Figure 3).
NOTE: The setscrews must be properly
installed as described above, or fan
wobble could result.
4. Make sure the grommet is properly
installed in the coupling cover then
slide the coupler cover on the downrod
until it rests on the motor housing.
Place the ceiling cover over the
downrod. Be sure both the ceiling cover
and the coupler cover are oriented
correctly (Figure 3).
BP7332 CF930 10/27/06 10:05 AM Page 6

7
PARTIALLY
ASSEMBLED
FAN
SOLID
STYROFOAM
FACING OUT
6" - 8"
GAP
Figure 5
CEILING
COVER
PIN
DOWNROD
HANGER BALL
SETSCREW
Figure 4
SLIDE FAN BLADE
INTO CENTER SLOT
FAN BLADE
M5 x 12mm WASHER
HEAD BLADE SCREWS
(3 per blade) CENTER SLOT
FAN
HOUSING
Figure 6
M4 x 10mm
SERRATED HEAD
SCREW (3)
LOWER
HOUSING
Figure 7
It is critical that the pin in the hanger ball
is properly installed and the setscrew
securely tightened. Failure to verify that
the pin and setscrew are properly
installed could result in the fan falling.
!WARNING
5. Reinstall the hanger ball (Figure 4) on the
downrod as follows. Route the motor
leads through the downrod. Position the
pin through the two holes in the downrod
and align the ball so the pin is captured in
the groove in the top of the hanger ball.
Pull the hanger ball up tight against the
pin and securely tighten the setscrew in
the hanger ball. A loose setscrew could
create fan wobble.
6. The fan comes with blue, black and
white leads that are 80” long. Before
installing fan, measure up approx-
imately 6 to 9-inches above top of
hanger ball/downrod assembly. Cut off
excess leads and strip back insulation
1/2-inch from end of leads.
7. Turn fan motor assembly upside down
in preparation for mounting fan blades.
Position the top and bottom halves of
the styrofoam packaging on end, with
solid styrofoam facing outward. Set
side-by-side on the floor with a six to
eight-inch gap between the halves
(Figure 5). Carefully place the partially
assembled ceiling fan on the styrofoam
halves, with the hanger ball/downrod
assembly positioned in the gap and the
fan motor assembly resting on top of
the styrofoam ends.
8. Slide blade through center slot in fan
housing. Mount blade to fan housing
using three M5 x 12mm washer head
blade screws (Figure 6).
9. Position the lower housing onto the fan
motor assembly, aligning each of the
the three holes. Attach the lower
housing to the fan motor assembly
using three M4 x 10mm serrated head
screws. Rotate the lower housing to
securely tighten by engaging the
screws in the two key hole slots
(Figure 7).
NOTE: Take care not to scratch fan
housing when installing blades.
BP7332 CF930 10/27/06 10:05 AM Page 7

1. Securely attach the hanger bracket to
the outlet box using the two screws
supplied with the outlet box (Figure 11).
How to Hang
Your Ceiling Fan
The fan must be hung with at least 7' of
clearance from floor to blades (Figure 10).
!WARNING
The outlet box and joist must be securely
mounted and capable of supporting at
least 50 lbs. Use only a U.L. outlet box
listed as “Acceptable for Fan Support”.
!WARNING
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
!WARNING
CEILING
FLOOR
AT
LEAST
7'
Figure 10
8
NOTE: Make sure wires are not pinched
between fan motor assembly and lower
housing.
10. Connect the black wire of the light kit
assembly to the blue wire of the fan
motor assembly using one wire
connector (supplied). Connect the
white wire of the light kit assembly to
the white wire of the fan motor
assembly using a supplied wire
connector (Figure 8).
WIRE
CONNECTOR
WHITE WIRE FROM THE
LIGHT KIT ASSEMBLY
WHITE WIRE FROM FAN
MOTOR ASSEMBLY
BLUE WIRE FROM FAN
MOTOR ASSEMBLY
BLACK WIRE FROM THE
LIGHT KIT ASSEMBLY
Figure 8
M4 x 10mm
SERRATED HEAD
SCREW (3)
LIGHT KIT
ASSEMBLY
KEY HOLE
SLOT (2)
Figure 9
NOTE: Make sure all wires and
connector are tucked under the light kit
assembly and not pinched between
light kit assembly and lower housing.
11. Position the light kit assembly onto the
lower housing, aligning each of the the
three holes. Attach the light kit
assembly to the lower housing, using
three M4 x 10mm serrated head
screws. Rotate the light kit assembly
to securely tighten by engaging the
screws in the two key hole slots
(Figure 9).
BP7332 CF930 10/27/06 10:05 AM Page 8

9
2. Carefully lift the fan and seat the
hanger ball/downrod assembly on the
hanger bracket that was just attached
to the outlet box (Figure 12). Be sure
the groove in the ball is lined up with
the tab on the hanger bracket
(Figure 11).
Hanger bracket must seat firmly against
outlet box. If the outlet box is recessed,
remove wall board until bracket contacts
box. If bracket and/or outlet box are not
securely attached, the fan could wobble
or fall.
!WARNING
Failure to seat tab in groove could cause
damage to electrical wires and possible
shock or fire hazard.
!WARNING
To avoid possible fire or shock, do not
pinch wires between the hanger
ball/downrod assembly and hanger
bracket.
!WARNING
TWO SCREWS
SUPPLIED
WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
NOTE: CEILING COVER, SUPPLY WIRES AND FAN
WIRES OMITTED FOR CLARITY.
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
Figure 11
Figure 12
1. Position the supply wires to the left side
of the outlet box (Figure 13); position
the fan wires to the right side. Partially
insert the remote control receiver (flat
side up) until one end rests on the
hanger ball as shown in Figure 13.
NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
2. Refer to Figures 13 and 14 and connect
the receiver wires to the supply wires
and the fan motor wires as follows:
a. Securely connect the green grounding
wires from the hanger ball and the
hanger bracket to the supply grounding
conductor (this may be a bare wire or a
wire with green insulation).
b. Securely connect the supply white
(neutral) wire to the receiver white
(AC IN N) wire.
c. Securely connect the supply black wire
(hot) wire to the receiver black (AC IN
L) wire.
d. Securely connect the fan motor white
wire to the receiver white (TO MOTOR
N) wire.
How to Wire
Your Ceiling Fan
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse box before wiring. All wiring must be
in accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
!WARNING
If you feel that you do not have enough
electrical wiring knowledge or
experience, have your fan installed by a
licensed electrician.
CAUTION: To reduce the risk of
electrical shock, disconnect the
electrical supply circuit before
installing the fan, light kit or receiver.
BP7332 CF930 10/27/06 10:05 AM Page 9

10
SW101 FAN/LIGHT WALL
CONTROL (SUPPLIED) BLACK BLACK
WHITE
RED
BLACK
WHITE
HANGER BALL
GREEN WIRE (GROUND)
FROM HANGER BALL AND
HANGER BRACKET
TWO-CONDUCTOR
CABLE (WITH
GROUND)
BLACK
(HOT)
WHITE
GROUND
TO
120-
VOLT
SUPPLY WHITE
BLUE
WHITE
BLUE
EMERSON®
HI
MED
LOW
FAN OFF
LIGHT
ONOFF
Figure 14
Check to see that all connections are
tight, including ground, and that no bare
wire is visible at the wire connectors,
except for the ground wire. Do not
operate fan until blades are in place.
Noise and fan damage could result.
!WARNING
e. Securely connect the fan motor black
wire to the receiver red (TO MOTOR L)
wire.
f. Securely connect the fan motor blue
wire to the receiver blue (FOR
LIGHT) wire.
GREEN GROUND
WIRE FROM
HANGER BRACKET
RECEIVER RED WIRE
RECEIVER WHITE WIRE
FAN WHITE WIRE
FAN
BLACK
WIRE
ANTENNA
AC
I
N
N
AC IN L
FOR LIGHT
TO MOTOR N
RECEIVER BLUE
WIRE
RECEIVER
BLACK WIRE
RECEIVER WHITE
WIRE
SUPPLY WHITE WIRE
(NEUTRAL)
SUPPLY BLACK
WIRE (HOT)
GROUND WIRE
GREEN GROUND
WIRE FROM
HANGER BALL
FAN BLUE WIRE
1-1/4" THREADED
STUD (2)
TO MOTOR L
Figure 13
BP7332 CF930 10/27/06 10:05 AM Page 10