Emerson CURVA SKY CF152ORB00 User manual

Part No. F40BP74070001 Form No. BP7407-1
UL Model No.: CF144 & CF152
READ AND SAVE THESE INSTRUCTIONS
CURVA SKY™
44” & 52” Damp & Wet
Location Snugger Ceiling Fan
Owner's Manual
CF144BS00
Brushed Steel
CF144CRM00
Chrome
44” Model Numbers
for Damp Locations
CF144WW00
Appliance White
CF144ORB00
Oil Rubbed Bronze
44” Model Numbers
for Wet Locations
CF152BS00
Brushed Steel
CF152CRM00
Chrome
52” Model Numbers
for Damp Locations
CF152WW00
Appliance White
CF152ORB00
Oil Rubbed Bronze
52” Model Numbers
for Wet Locations
Net Weight: 18.5 Lbs. Net Weight: 19.4 Lbs.
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 1

WARNING: To avoid fire, shock, and serious personal injury, follow these
instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service
panel disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a warning
device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Always turn off the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before
wiring, and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA
70-2008 and Local Codes. Use the National Electrical Code if Local Codes do not
exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably
supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for
Fan Support”, and use the mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent
accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling
fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used
with fan speed control Model No. UC8013R, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this
product and/or any accessories designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with
this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when
installing the blade flanges, balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electric shock, this fan must be installed with an
isolating remote control/switch.
!WARNING
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2UL Model No.: CF144 & CF152
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 2

3
THE FAN MODELS CF144BS, CF144CRM, CF152BS & CF152CRM ARE SUITABLE
FOR DAMP LOCATIONS SUCH AS COVERED PORCHES, COVERED PATIOS,
AND COVERED DECKS...ANYWHERE THERE IS A ROOF OVERHEAD.
THE FAN MODELS CF144WW, CF144ORB, CF152WW & CF152ORB ARE
SUITABLE FOR WET LOCATIONS SUCH AS PORCHES, PATIOS, AND DECKS.
This Manual is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Do not install or use fan if any part is
damaged or missing. Call Toll-Free:
1-800-654-3545
!WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
!WARNING
Tools Needed for Assembly
One Phillips head screwdriver
One wire stripper
One stepladder
Materials
Wiring, outlet box and box connectors
must be of type required by the local code.
The minimum wire would be a 3-conductor
(2-wire with ground) of the following sizes:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Before assembling your ceiling fan, refer
to section on proper method of wiring
your fan (Page 7). If you feel you do not
have enough wiring knowledge or
experience, have your fan installed by a
licensed electrician.
!WARNING
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.
NOTE: If you are uncertain of part
description, refer to exploded view
illustration.
a. Fan motor assembly
b. One ceiling trim ring
c. One ceiling mounting plate
d. Three fan blades
e. One lower housing
f. One light kit plate
g. One glass shade
h. One no-light cover plate
i. One 6-speed electronic receiver
control with parts bag
j. One 6-speed handheld transmitter with
wall bracket
k. Two 50W halogen mini candelabra
bulbs
l. One loose parts bag containing:
1. Three 12 ga. wire connectors
2. One spare M5 x 10mm pan head
ceiling cover screw with washer
3. Ten M5 x 16mm flange head
blade screws
4. One spare M4 x 10mm pan head
screw for lower housing and
light kit
5. One balancing kit
1. Open carton containing fan. Remove
top half of styrofoam unit. Remove
parts and check to see that you have
received the following parts:
UL Model No.: CF144 & CF152
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 3

4
2. Remove the fan motor assembly from
the protective plastic bag. Place all
carton contents on a protective surface.
B. CEILING
TRIM RING
D. FAN BLADES (3)
G. GLASS SHADE
A. FAN MOTOR
ASSEMBLY
H. NO-LIGHT
COVER PLATE
E. LOWER
HOUSING
K. 50W MINI CANDELABRA
HALOGEN BULBS
L. LOOSE
PARTS BAG
J. 6-SPEED
HANDHELD
TRANSMITTER
F. LIGHT
KIT PLATE
I. 6-SPEED
ELECTRONIC
RECEIVER
C. CEILING
MOUNTING PLATE
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost.
PROTECTIVE
PLASTIC BAG
UL Model No.: CF144 & CF152
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 4

5
Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.
General
Your Emerson ceiling fan comes supplied
with a Fan/Light Remote Control which
consists of a receiver mounted inside the
ceiling cover of the fan motor housing. This
system allows you to regulate your ceiling
fan speed and light intensity.
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
!WARNING
If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.
IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric Fan/Light Remote
Control supplied with the fan.
Electrical Requirements
Ceiling Fan Procedures
How to Assemble Your
Ceiling Fan
Turning off wall switch is not sufficient. To
avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring. All
wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
!WARNING
UL Model No.: CF144 & CF152
SLIDE FAN BLADE
INTO BLADE
CENTER SLOT
FAN
BLADE
M5 x 16mm FLANGE
HEAD BLADE SCREWS
(3 per blade)
BLADE
SLOT
FAN
HOUSING
Figure 1
1. Position the fan motor assembly upside
down in preparation for mounting the
three fan blades.
2. Slide blade through blade slot in fan
housing assembly. Mount blade to fan
housing using three M5 x 16mm flange
head blade screws (Figure 1).
3. Complete the remaining two blades
installation per the above instructions.
NOTE: Take care not to scratch fan
housing assembly when installing
blades.
4. Remove one of the three screws in the
motor housing assembly and loosen
the remaining two screws (Figure 2).
5. Attach the lower housing assembly to
the fan motor using the two key slot
holes (Figure 2). Secure the lower
housing assembly by tightening the two
screws. Reinstall the screw that was
previously removed.
REMOVE M4 x 10mm
PAN HEAD SCREW LOWER HOUSING
KEY HOLE
SLOT (2)
Figure 2
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 5

CEILING
FLOOR
AT
LEAST
7'
Figure 5
6UL Model No.: CF144 & CF152
9. Tuck the wires and connectors into the
fan housing. Position the light kit plate
into the fan housing by placing the cut
out notches over the fan housing
dimples (Figure 4).
10. Attach the light kit plate assembly to
the lower housing using two key slot
holes (Figure 4). Secure the light kit
plate assembly by tightening the two
screws. Reinstall the screw that was
previously removed. 1. Disconnect electrical power to the branch
circuit at the circuit breaker or fuse box
before attempting to install the ceiling fan
mounting plate on the outlet box.
NOTE: Make sure all wires and
connectors are tucked under the light
kit plate and not pinched between light
kit plate and fan housing.
REMOVE M4 x 10mm
PAN HEAD SCREW
KEY HOLE SLOT (2)
LOWER HOUSING
LIGHT KIT
PLATE
DIMPLES
CUT OUT
NOTCHES
Figure 4
How to Hang
Your Ceiling Fan
The fan must be hung with at least 7' of
clearance from floor to blades (Figure 5).
!WARNING
The outlet box and joist must be securely
mounted and capable of supporting at
least 50 lbs. Use only a U.L. outlet box
listed as “Acceptable for Fan Support”.
!WARNING
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
!WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring. All wiring
must be in accordance with National and
Local codes and the ceiling fan must be
properly grounded as a precaution against
possible electrical shock.
!WARNING
6. Remove and retain the wire connectors
from the white and blue wires.
7. Connect the white wire from the ceiling
fan to the white wire of the light kit plate
(Figure 3). Connect the blue wire from
the ceiling fan to the black wire of the
light kit plate. Use wire connectors
(previously removed) to make
connections.
8. Remove one of the three screws in the
lower housing and loosen the
remaining two screws (Figure 3).
LIGHT KIT
BLACK WIRE
LIGHT KIT
WHITE WIRE
FAN MOTOR
WHITE WIRE
REMOVE ONE
LOWER HOUSING
SCREW
FAN MOTOR
BLUE WIRE
Figure 3
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 6

7UL Model No.: CF144 & CF152
2. Pull the electrical supply black, white
and ground wires through the center
opening of the ceiling mounting plate
before securing the plate to the outlet
box (Figure 6).
3. Position the ceiling mounting plate onto
the outlet box and secure using the two
outlet box screws, supplied with outlet
box (Figure 6).
Figure 6
OUTLET BOX
SCREWS (2)
CEILING
MOUNTING
PLATE HOOK
CEILING
MOUNTING
PLATE
OUTLET
BOX
4. Slide the ceiling trim ring over the fan
motor assembly and let it rest on the
motor assembly (Figure 7).
5. Place the motor assembly onto the
ceiling mounting plate hook during
wiring fan motor assembly to outlet box
(Figure 8).
CEILING
TRIM
RING
FAN MOTOR
ASSEMBLY
Figure 7
FAN MOTOR
ASSEMBLY
HOOK
CEILING
MOUNTING
PLATE
Figure 8
How to Wire
Your Ceiling Fan
Turning off wall switch is not sufficient. To
avoid possible electrical shock, be sure
electricity is turned off at the main fuse
box before wiring. All wiring must be in
accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
!WARNING
If you feel that you do not have enough
electrical wiring knowledge or
experience, have your fan installed by a
licensed electrician.
CAUTION: To reduce the risk of electrical
shock, disconnect the electrical supply
circuit before installing the fan, light kit
or receiver.
NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
1. Position the receiver into the fan motor
housing as shown in Figure 9.
2. Refer to Figures 9 and 10 to connect
the receiver wires to the supply wires
and the fan motor wires using the wire
connectors supplied with the fan as
follows:
a. Securely connect the green grounding
wire from the ceiling mounting plate
and green grounding wire from fan
body to the supply green grounding
conductor (this may be a bare wire or a
wire with green insulation).
b. Securely connect the supply white
(neutral) wire to the receiver white
(AC IN N)/(TO MOTOR N) wire and
white (neutral) fan wire.
c. Securely connect the supply black wire
to the receiver black/white (AC IN L)
wire.
d. Securely connect the fan motor black
wire to the receiver black (TO MOTOR
L) wire.
e. Securely connect the fan motor blue
wire to the receiver blue (FOR
BOTTOM LIGHT) wire.
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 7

UL Model No.: CF144 & CF152
3. After connections have been made,
turn leads upward and carefully push
leads into the outlet box, with the white
and green leads on one side of the
outlet box and the black and blue leads
on the other inside of the outlet box.
To avoid possible fire or shock, make
sure that the electrical wires are
completely inside the outlet box and
not pinched between the ceiling
mounting plate and the fan motor
housing assembly.
!WARNING
6. Position the ceiling trim ring over each
of the protruding ceiling cover screw
heads and rotate the ceiling trim ring
clockwise to secure (Figure 12).
FAN MOTOR
HOUSING
ASSEMBLY
CEILING
MOUNTING PLATE M5 x 10mm PAN
HEAD CEILING
COVER SCREWS
WHITE
SUPPLY
WIRE
BLACK FAN WIRE
RECEIVER
WHITE FAN WIRE
BLUE RECEIVER
WIRE
BLUE FAN WIRE
BLACK
SUPPLY
WIRE
WHITE
RECEIVER
WIRE
BLACK RECEIVER
WIRE
BLACK/WHITE
RECEIVER WIRE
GREEN
GROUND WIRE
GREEN MOUNTING
PLATE WIRE
GREEN FAN WIRE
Figure 11
Figure 10
FAN MOTOR
HOUSING
ASSEMBLY
CEILING
TRIM RING
CEILING COVER SCREW
HEADS (4)
Figure 12
8
Check to see that all connections are
tight, including ground, and that no bare
wire is visible at the wire connectors,
except for the ground wire. Do not operate
fan until blades are in place. Noise and
fan damage could result.
!WARNING
FAN BLACK
WIRE
FAN &
RECEIVER
BLUE WIRES
SUPPLY
BLACK WIRE
SUPPLY,
RECEIVER & FAN
WHITE WIRES
RECEIVER BLACK
WIRE
RECEIVER
RECEIVER
BLACK/WHITE
WIRE
ANTENNA
WIRE
SUPPLY & CEILING MOUNTING
PLATE GREEN WIRES
FAN ASSEMBLY
GREEN WIRE
Figure 9
4. Remove one of the four screws in the
ceiling mounting plate and loosen the
remaining three screws (Figure 11).
5. Unhook the fan motor housing from the
ceiling mounting plate hook and lift the
fan motor housing assembly up to the
ceiling mounting plate. Align and
engage the motor assembly slots with
the three screw heads previously
loosened by rotating the fan motor
housing assembly to engage the screw
heads and all three slots. Install the
previously removed M5 x 10mm screw
and secure the assembly to the plate
(Figure 11). Completely tighten all four
screws.
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 8

1. Screw in two 50-watt (maximum)
halogen mini candelabra base bulbs in
the light kit plate sockets (Figure 13).
50-WATT (maximum)
HALOGEN MINI
CANDELABRA BASE
BULBS (2)
LIGHT KIT PLATE
SOCKETS (2)
Figure 13
2. Place the glass shade into the opening
in the fan motor housing assembly,
aligning the three flat areas on the top
edge of the glass with the three raised
dimples on the fan motor housing
assembly and turn the glass shade
clockwise until it stops (Figure 14).
NOTE: periodically check that the glass
shade is seated fully clockwise in the
fan motor housing assembly.
UL Model No.: CF144 & CF152
How to Assemble Your
Light Kit Glass Shade
9
DIMPLES (3)
FLAT AREA (3) GLASS
BOWL
Figure 14
Figure 15
How to Assemble Your
No Light Cover Plate
DIMPLES (3)
FLAT AREA (3) COVER
PLATE
1. Place the cover plate onto the lower
housing aligning the three flat areas on
the top flange of the cover plate with
the three pins on the inside of the fan
motor housing assembly (Figure 15).
Then turn the cover plate clockwise
until it stops turning.
2. Your cover plate is now installed
Do not install any light bulbs into the
light kit plate if using the cover plate.
Installation of light bulbs when using
the cover plate could result in fire,
shock and serious personal injury.
!WARNING
DO NOT INSTALL LIGHT BULBS
WHEN USING THE COVER PLATE
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 9

10 UL Model No.: CF144 & CF152
General
Your Emerson Ceiling Fan/Light Remote
Control consists of hand-held transmitter
and a receiver which is mounted under the
fan ceiling cover. The remote control is
designed to separately control your ceiling
fan speed and light intensity.
The remote control transmitter is powered
by two AAA alkaline batteries (included).
To prevent possible damage if the
batteries should leak, be sure to remove
the batteries when the control is not to be
used for an extended period of time.
Code switches in the transmitter and
receiver may be set in 32 different
positions. If your fan and light go on and off
without using your control, you may be
getting interference from other remote
units such as garage door openers, car
alarms or security systems. To remedy this
situations, simply change the combination
code in your transmitter and receiver.
Preset Memory Feature
Your Emerson receiver is equipped with a
preset memory feature. If the AC supply to
the receiver is powered through a wall
switch, when the switch is turned OFF, the
control will remember the light intensity
and fan speed. When the switch is turned
back ON the light and fan will resume
operation as they were prior to the switch
being turned OFF.
REMOTE CONTROL
PROCEDURES
CODE
SWITCHES
SR600 REMOTE
CONTROL
BATTERY
COMPARTMENT
COVER
TWO AAA
BATTERIES
REMOTE CONTROL
LEVERS
ON
1234
5I
Figure 16
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE SCREW
HOLES FOR INSTALLATION
COVER
WALL
BRACKET
SCREW
HOLES (2)
Figure 17
Installation of Storage
Bracket for
Remote Control
A storage bracket is provided for holding
your remote control when not in use. If you
desire to use the bracket, install it on a wall
that is away from excess heat or humidity
(Figure 17).
Installation of Battery
1. Remove the battery cover by pressing
firmly below the arrow and sliding the
cover off the control (Figure 16).
2. Install two AAA alkaline batteries and
reinstall the battery cover.
BP7407-1 44" & 52" Curva Sky 8/31/10 4:10 PM Page 10