Emerson ODYSSEY CF2454WW02 User manual

READ AND SAVE THESE INSTRUCTIONS
Model No.
CF2454WW02 CF2454BS02
CF2454PW02 CF2454BQ02
THE ODYSSEY Series
Ceiling Fan Owner's Manual
Part No. F40BP72110008 Form No. BP7211-8
®
Net Weight: 26.0 Lbs.

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service dis-
connecting means cannot be locked, securely fasten a warning device, such as a tag, to the service
panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if Local
Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted an capable of reliably supporting a least 50
pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in
doubt.
4. The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not
know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use this product by Emerson Company could result in
personal injury or property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
2
WARNING
!

1. Open styrofoam unit containing fan. Remove upper
and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:
a. One fan motor and housing assembly
b. One motor coupling cover
c. One ceiling cover
d. Five fan blades
e. Five blade holder caps (left)
f. Five blade holder caps (right)
g. One hanger ball/downrod assembly
h. One hanger bracket
i. One light kit adapter assembly
j. One light kit plate assembly
k. One light kit glass
l. Two die cast light kit glass holders
m.One uplight lead assembly
n. One loose parts bag containing:
1. One setscrew
2. One 5/32" hex wrench
3. One 3/16” hex wrench
4. Four 8-32 x 1-1/4” threaded studs
5. Four knurled knobs
6. Four lockwashers
7. Seven wire connectors
8. Three 8-32 x 3/8" phillips head screws
9. One hairpin clip
10. One clevis pin
11. Twenty-one 10-32 x 3/8" pan head screws
12. One flatwasher
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One six-inch blade screwdriver One stepladder
One Phillips head screwdriver One wire stripper
Seven wire connectors(supplied.)
MATERIALS
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire size,
to right:
3
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
BLADE HOLDER
CAPS (LEFT)
BLADE HOLDER
CAPS (RIGHT)
UPPER STYROFOAM
SECTION
CEILING
COVER
FAN BLADES
MOTOR
COUPLING
COVER
HANGER BALL/
DOWNROD
ASSEMBLY
HANGER
BRACKET
LOOSE
PARTS
BAG
CENTER
STYROFOAM
SECTION
LIGHT KIT
PLATE
ASSEMBLY
LIGHT KIT
GLASS
LIGHT KIT
ADAPTER
ASSEMBLY
LOWER
STYROFOAM
SECTION
FAN MOTOR
AND HOUSING
ASSEMBLY
UPLIGHT
LEAD ASSEMBLY
DIE CAST
GLASS HOLDERS
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or acces-
sories not designated for use with this product by
Emerson Company could result in personal injury or
property damage.
WARNING
!
WARNING
!
WARNING
!

Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and capa-
ble of withstanding a load of at least 50 pounds.
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
4
SECTION A
Assembly Instructions
for Installing the CF2454
Ceiling Fan with a
SW375 Receiver and
a SR330 Remote Control or
with a SW350 Wall Control
1. Cut the white, blue, and black wires about 3"
above the motor coupling (Figure 1). Strip insula-
tion 1/2" from end of wires and install a wire con-
nector on the black wire; this wire will not be used.
Remove the wire connectors from the red and
brown wires.
2. Loosen the setscrew in the hanger ball, slide the ball
down the downrod , and remove the clevis pin. Then
slide the hanger ball off the downrod (Figure 2).
Retain all parts for reinstallation in step 11.
3. Push the wiring harness connector (supplied with
the remote control) and the connector on the blue
wire (supplied with the SW375 Receiver) and the
uplight yellow lead assembly (supplied with the
fan) through the downrod until they extend about
4" out of the downrod. (Figure 3).
4. Cut all wires approximately 3" from the end of the
downrod’. Strip insulation 1/2" from end of wires.
MOTOR
COUPLING
3"
WHITE WIRE BLACK WIRE
BLUE WIRE
REMOVE WIRE
CONNECTORS
FROM RED AND
BROWN WIRES
INSULATE BLACK
WIRE USING WIRE
CONNECTOR
MOTOR COUPLING SLOT
YELLOW
WIRE
Figure 1
HANGER BALL
DOWNROD
CLEVIS PIN
SETSCREW
Figure 2
4"
DOWNROD
CUT HERE
3"
UPLIGHT YELLOW LEAD ASSEMBLY
WIRING
HARNESS
BLUE WIRE
Figure 3
IF THE CF2454 CEILING FAN IS BEING
INSTALLED WITH ANY OTHER CONTROL
METHOD, SKIP SECTION A AND GO TO
SECTION B TO BEGIN ASSEMBLY
INSTRUCTIONS.
Electrical Requirements
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
The Emerson CF2454 Ceiling Fan is designed to be
operated from a SR330 Remote Control, from a
SW350 Wall Control with a SW375 Receiver, or from
other fan/light controls. There are not controls supplied
with the ceiling fan. If you are going to control your
ceiling fan with a SR330 Remote Control or with a
SW350 Wall Control, proceed to “SECTION A”. If you
are to control your ceiling fan in any other manner,
proceed to “SECTION B”.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
WARNING
!
WARNING
!

9. Screw two 1-1/4” threaded studs (supplied) into
the motor (Figure 6). Leave approximately 7/8” of
the stud extending above the motor. Slide the
motor cover over the downrod and rotate the cover
until the threaded studs protrude; install two
knurled knobs (supplied) to secure the cover.
NOTE: Make sure the unused black motor lead is
capped with a wire connector. Make sure all wire
connectors are completely inside motor coupling
cover and not pinched between the motor cou-
pling cover and motor.
10. Position the ceiling cover over the downrod . Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 7).
7/8"
RED LEAD
WIRE
CONNECTORS
KNURLED KNOB
1-1/4" THREADED
STUD
MOTOR
BRACKET
MOTOR
COUPLING
COVER
WIRE CONNECTOR
YELLOW LEADS
BROWN LEAD
Figure 6
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
MOTOR COUPLING
HAIRPIN
CLIP
CLEVIS
PIN
DOWNROD
YELLOW LEADS TO
BE POSITIONED IN
SLOT IN MOTOR
COUPLING
CLEVIS
PIN
Figure 5
5
5. Using wiring connectors (supplied), connect the
white, red, blue, brown, and yellow wires from the
downrod to the white, red, blue, brown and yellow
wires of the ceiling fan (Figure 4). Wires must be
connected color-to-color.
6. Fold all wires from the downrod into the slot in the
motor coupling, slide the downrod down the wires
and seat the downrod in the motor coupling. All
wires and wire connectors should be placed
through the motor coupling slot beneath the down-
rod (See Figure 5).
7. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip. The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod (Figure 5). Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose.
8. Install the setscrew (supplied in the loose parts
bag) in the motor coupling and tighten using the
5/32” setscrew wrench (supplied) (Figure 5).
FAN
HOUSING
FAN BLADES REMOVED
FOR CLARITY
TO
120V SUPPLY
TO
120V SUPPLY
DOWNROD
WHITE WIRE
BLACK WIRE
WIRING HARNESS
CONNECTOR
YELLOW WIRE
TO YELLOW
WIRE
BLUE WIRE
TO
BLUE WIRE
SW375 RECEIVER
BROWN WIRE
TO BROWN WIRE
YELLOW WIRE
TO YELLOW WIRE
LISTED GENERAL
USE ON/OFF
WALL SWITCH
(MUST BE
USED WITH
SR330 REMOTE
CONTROL)
RECEIVER
CONNECTOR
RED WIRE
TO RED WIRE
LIGHT
FIXTURE
WHITE WIRE
TO WHITE WIRE
BLACK WIRE
(NOT USED)
BLUE WIRE
TO BLUE WIRE
BLACK WIRE
WHITE WIRE
BLACK
WIRE WHITE
WIRE
BLACK
WHITE
BLACK
SW350
WALL
CONTROL
Figure 4
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely tight-
ened. Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!

15. Securely connect the black wire from the light kit
plate assembly to the blue wire from the motor
shaft using a wire connector (supplied) (Figure
10). Connect the white wire from the plate assem-
bly to the white wire from the motor shaft using a
wire connector (supplied).
16. Secure the light kit plate assembly to the light kit
adapter assembly by threading three 8-32 x 3/8”
phillips head screws (supplied) into the threaded
holes in the adapter assembly. (Figure 11).
NOTE: Do not pinch wires between the light kit
plate assembly and the adapter assembly.
17. Lift the fan assembly from the styrofoam and
remove the center styrofoam section. Turn the fan
assembly over and carefully position it on the
upper styrofoam section so that the hanger
ball/downrod assembly is at the top (Figure 12).
LIGHT KIT
ADAPTER
ASSEMBLY
WIRE
CONNECTORS
BLUE WIRE
WHITE
WIRES
LIGHT KIT
PLATE
ASSEMBLY
BLACK WIRE
Figure 10
LIGHT KIT ADAPTER
ASSEMBLY LIGHT KIT PLATE
ASSEMBLY
8-32 X 3/8"
PHILLIPS HEAD
SCREWS (3)
Figure 11
6
11. Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 7). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is cap-
tured in the groove in the top of the hanger ball.
Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball. A
loose setscrew could create fan wobble.
12. Position the center styrofoam section on the
upper section, and then position the fan motor
and housing on the center section so that the bot-
tom of the motor is facing you (Figure 8). The sty-
rofoam sections will hold the assembly while you
perform the following steps.
13. Position the flatwasher (supplied in parts bag) on
the motor shaft (Figure 8).
14.Using the 3/16” setscrew wrench (supplied),
loosen the setscrew in the collar, then screw the
light kit adapter assembly onto the motor shaft
(Figure 9). Tighten the setscrew to secure the
adapter assembly to the shaft. Securely engage
the connector from the reversing switch to the con-
nector from the motor shaft.
CEILING COVER
SETSCREW
PIN
HANGER BALL
DOWNROD
Figure 7
REVERSING
SWITCH
CONNECTORS
MOTOR SHAFT
COLLAR
SETSCREW
LIGHT KIT
ADAPTER
ASSEMBLY
Figure 9
CENTER
STYROFOAM
SECTION
FAN MOTOR AND
HOUSING ASSEMBLY
UPPER
STYROFOAM
SECTION
FLATWASHER
Figure 8
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are proper-
ly installed could result in the fan falling.
WARNING
!

7
UPPER
STYROFOAM
SECTION
FAN MOTOR AND
HOUSING ASSEMBLY
Figure 12
18. Position one fan blade on the flange assembly and
secure by installing the left and right blade holder
caps using two 10-32 x 3/8” pan head screws (sup-
plied) for each holder cap (Figure 13). Install the
remaining four fan blades using the same procedure.
19. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box. (Figure 15.)
20. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 16). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 15).
LEFT BLADE
HOLDER CAP
FLANGE
ASSEMBLY
10-32 X 3/8"
PAN HEAD SCREW
(2 PER HOLDER CAP)
RIGHT BLADE
HOLDER CAP
Figure 13
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
HANGER
BRACKET
TAB
OUTLET
BOX
Figure 15
CEILING
FLOOR
AT LEAST
7'
Figure 14
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
Figure 16
21. Position the receiver (supplied with the SR330
Remote Control or SW350 Wall Control) by
passing the opening in the receiver over the
downrod (Figure 17).
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 14).
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
WARNING
!
WARNING
!
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is ground-
ed, contact a licensed electrician for advice, as it
must be grounded for safe operation.
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
WARNING
!

22. Connect the black wire from the wiring harness to
the black (hot) supply wire (Figure 4). Connect
the white wire from the wiring harness to the
white (neutral) supply wiring. Connect the green
ground wires from the hanger bracket and the
hanger ball to the supply ground wire. Use wire
connectors supplied with your ceiling fan.
23. Securely connect the wiring harness connector to
the receiver connector, and connect the blue and
yellow wires to the blue and yellow wires from the
receiver (Figure 4).
24. Turn the receiver so that the flat side aligns with
the open side of the hanger bracket (Figure 17).
Fold and position the wires into the space above
the hanger ball and into the outlet box.
25. Feed the wires and connectors around the out-
side of the receiver, through the open side of the
hanger bracket, and into the outlet box. Slide the
receiver up and over the hanger bracket. Press
the receiver against the ceiling.
26. To complete the ceiling fan assembly, skip to the
“FINAL ASSEMBLY” section of this Owner’s
Manual.
HANGER
BRACKET HANGER
BALL
CEILING
COVER
SW375
RECEIVER
FLAT SIDE
OPEN
SIDE
Figure 17
8
SECTION B
Assembly Instructions for
Installing the CF2454 Ceiling Fan
with Any Other Control Method
(excluding the SW375 Receiver,
SR330 Remote Control or the
SW350 Wall Control)
1. Remove the fan motor and housing assembly from
the lower styrofoam section and position it in the lower
section so that the top of the motor is facing you.
2. Separate, untwist and unkink the four motor leads.
3. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 18). Remove the pin from the
downrod , then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in step 9.
4. Push the uplight yellow lead assembly connector
through the downrod (Figure 19) until it extends
about 4”.
5. Cut the yellow lead approximately 3” from the end
of the pipe. Strip insulation 1/2” from end of the
wires.
6. Using the wire connector supplied, connect the
uplight yellow lead assembly to the yellow lead
from the fan motor and housing assembly.
7. Route the white, blue, and black motor leads through
the downrod. Fold the yellow wire into the slot in the
motor coupling, slide the downrod down the wires and
seat the downrod in the motor coupling (Figure 20).
8. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin and
secure with the hairpin clip (Figure 20). The clevis pin
must go through the holes in the motor coupling and
the holes in the downrod . Push the straight leg of the
hairpin clip through the hole near the end of the cle-
vis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must be
properly installed to prevent the clevis pin from work-
ing loose. Pull on the hanger ball to make sure the
clevis pin is properly installed.
HANGER BALL
DOWNROD
PIN
SETSCREW
Figure 18
4"
DOWNROD
CUT
HERE
3"
UPLIGHT YELLOW
LEAD ASSEMBLY
Figure 19
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!

9
9. Install the setscrew (supplied in loose parts bag) in
the motor coupling and tighten using the 5/32"
setscrew wrench (supplied) (Figure 21).
10.Screw two 1-1/4” threaded studs (provided) into
the motor (Figure 22). Leave approximately 7/8” of
the stud extending above the motor. Slide the
motor cover over the downrod and rotate the cover
until the threaded studs protrude; install two
knurled knobs (supplied) to secure the cover.
NOTE: Make sure the red and brown leads are
capped with wire connectors. Make sure red,
brown, and yellow wire connectors are completely
inside motor coupling cover and not pinched
between the motor coupling cover and motor.
11.Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 23).
12.Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 23). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is
captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin
and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
13.The blue, black, yellow and white leads exiting the
downrod are 80-inches long. Before installing fan,
measure up approximately 6 to 9-inches above the
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
NOTE: If you are installing your fan with a SR330
Remote Control or SW350 Wall Control, Do Not
Cut Terminal Off of the Yellow Lead.
(See Section A.)
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
MOTOR COUPLING
HAIRPIN
CLIP
CLEVIS
PIN
DOWNROD
YELLOW LEADS TO
BE POSITIONED IN
SLOT IN MOTOR
COUPLING
CLEVIS
PIN
Figure 20
DOWNROD
SETSCREW
Figure 21
7/8"
RED LEAD
WIRE
CONNECTORS
KNURLED KNOB
1-1/4" THREADED
STUD
MOTOR
BRACKET
MOTOR
COUPLING
COVER
WIRE CONNECTOR
YELLOW LEADS
BROWN LEAD
Figure 22
CEILING COVER
SETSCREW
PIN
HANGER BALL
DOWNROD
Figure 23
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely tight-
ened. Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are proper-
ly installed could result in the fan falling.
WARNING
!

10
14. Position the center styrofoam section on the
upper section, and then position the fan motor
and housing on the center section so that the bot-
tom of the motor is facing you (Figure 24). The
styrofoam sections will hold the assembly while
you perform the following steps.
15. Position the flatwasher (supplied in parts bag) on
the motor shaft (Figure 24).
16. Using the 3/16” setscrew wrench (supplied),
loosen the setscrew in the collar, then screw the
light kit adapter assembly onto the motor shaft
(Figure 25). Tighten the setscrew to secure the
adapter assembly to the shaft. Securely engage
the connector from the reversing switch to the
connector from the motor shaft.
17. Securely connect the black wire from the light kit
plate assembly to the blue wire from the motor
shaft using a wire connector (supplied)
(Figure 26). Connect the white wire from the plate
assembly to the white wire from the motor shaft
using a wire connector (supplied).
18. Secure the light kit plate assembly to the light kit
adapter assembly by threading three 8-32 x 3/8”
phillips head screws (supplied) into the threaded
holes in the adapter assembly. (Figure 27).
NOTE: Do not pinch wires between the light kit
plate assembly and the adapter assembly.
19. Lift the fan assembly from the styrofoam and
remove the center styrofoam section. Turn the fan
assembly over and carefully position it on the
upper styrofoam section so that the hanger
ball/downrod assembly is at the top (Figure 28).
20. Position one fan blade on the flange assembly and
secure by installing the left and right blade holder
caps using two 10-32 x 3/8” pan head screws (sup-
plied) for each holder cap (Figure 29). Install the
remaining four fan blades using the same procedure.
REVERSING
SWITCH
CONNECTORS
MOTOR SHAFT
COLLAR
SETSCREW
LIGHT KIT
ADAPTER
ASSEMBLY
Figure 25
LIGHT KIT
ADAPTER
ASSEMBLY
WIRE
CONNECTORS
BLUE WIRE
WHITE
WIRES
LIGHT KIT
PLATE
ASSEMBLY
BLACK WIRE
Figure 26
LIGHT KIT ADAPTER
ASSEMBLY LIGHT KIT PLATE
ASSEMBLY
8-32 X 3/8"
PHILLIPS HEAD
SCREWS (3)
Figure 27
CENTER
STYROFOAM
SECTION
FAN MOTOR AND
HOUSING ASSEMBLY
UPPER
STYROFOAM
SECTION
FLATWASHER
Figure 24
LEFT BLADE
HOLDER CAP
FLANGE
ASSEMBLY
10-32 X 3/8"
PAN HEAD SCREW
(2 PER HOLDER CAP)
RIGHT BLADE
HOLDER CAP
Figure 29
UPPER
STYROFOAM
SECTION
FAN MOTOR AND
HOUSING ASSEMBLY
Figure 28