Emerson Rosemount 5900 User manual

www.rosemount-tg.com
Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900
Radar Level Gauge
Preliminary

Preliminary

Reference Manual
300520EN, Rev AA
November 2009 Rosemount 5900
www.rosemount-tg.com
Rosemount 5900
Radar Level Gauge
Cover Photo: 5900_coverphoto.tif
NOTICE
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure you thoroughly understand the contents before
installing, using, or maintaining this product.
For equipment service or support needs, contact your local Emerson Process
Management/Rosemount Tank Gauging representative.
Spare Parts
Any substitution of non-recognized spare parts may jeopardize safety. Repair, e.g.
substitution of components etc, may also jeopardize safety and is under no circumstances
allowed.
Rosemount Tank Radar AB will not take any responsibility for faults, accidents, etc caused
by non-recognized spare parts or any repair which is not made by
Rosemount Tank Radar AB.
Specific FCC Requirements (USA only)
Rosemount 5900 generates and uses radio frequency energy. If it is not installed and used
properly, that is, in strict accordance with the manufacturer´s instructions, it may violate
FCC regulations on radio frequency emission.
Rosemount TankRadar 5900 has been FCC certified under test conditions which assume a
metallic tank. Installation on a non-metallic tank is not certified, and is not allowed.
The FCC certificate for Rosemount 5900 requires that the tank is closed as far as emitted
radio energy is concerned. Tanks with open manholes, external-floating-roof tanks without
still pipes etc. are not covered by the certificate.
Preliminary

Preliminary

Reference Manual
300520EN, Rev AA
November 2009 Rosemount 5900 Series
www.rosemount-tg.com
Table of Contents
SECTION 1
Introduction
1.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.3 Manual Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.4 Service Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.5 Product Recycling/
Disposal1-5
1.6 Packing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.6.1 Reuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.6.2 Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.6.3 Energy recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
SECTION 2
Overview
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3 System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.4 Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.5 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
SECTION 3
Installation
3.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.2.1 Horn Antenna Requirements . . . . . . . . . . . . . . . . . . . 3-4
3.2.2 Parabolic Antenna Requirements . . . . . . . . . . . . . . . 3-6
3.2.3 Still Pipe Antenna Requirements . . . . . . . . . . . . . . . 3-10
3.2.4 LPG/LNG Antenna Requirements . . . . . . . . . . . . . . 3-13
3.3 Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
3.3.1 Horn Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
3.3.2 Parabolic Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
3.3.3 Array Antenna - Fixed version . . . . . . . . . . . . . . . . . 3-29
3.3.4 Array Antenna - Hinged Hatch . . . . . . . . . . . . . . . . . 3-32
3.3.5 LPG/LNG Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
3.4 Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
3.4.1 Cable/conduit entries . . . . . . . . . . . . . . . . . . . . . . . . 3-39
3.4.2 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39
3.4.3 Cable Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
3.4.4 Hazardous Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
3.4.5 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . 3-40
3.4.6 Power Budget. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
3.4.7 The Raptor Tankbus . . . . . . . . . . . . . . . . . . . . . . . . 3-41
3.4.8 Typical installations . . . . . . . . . . . . . . . . . . . . . . . . . 3-42
3.4.9 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43
3.4.10 Terminal Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-44
3.4.11 Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-47
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
TOC-2 Table of Contents
SECTION 4
Configuration
4.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2.1 Basic Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.2.2 Advanced Configuration. . . . . . . . . . . . . . . . . . . . . . . 4-3
4.2.3 Configuration Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.3 Basic Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.3.1 Tank Geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.3.2 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.3.3 Tank Shape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.4 Configuration Using Rosemount TankMaster . . . . . . . . . . . . . . 4-7
4.4.1 Installation Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.5 LPG Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.5.1 Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.5.2 LPG Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
SECTION 5
Operation
5.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Viewing Measurement Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
5.3 Alarm Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
SECTION 6
Service and
Troubleshooting
6.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.2.1 Viewing Input and Holding Registers . . . . . . . . . . . . . 6-2
6.2.2 Backing Up the Gauge Configuration. . . . . . . . . . . . . 6-4
6.2.3 To Recover a Backup Configuration Database . . . . . 6-6
6.2.4 Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.2.5 Upgrading the Gauge Software . . . . . . . . . . . . . . . . . 6-8
6.2.6 Write Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
6.2.7 Write Protection Switch . . . . . . . . . . . . . . . . . . . . . . 6-11
6.2.8 Logging Measurement Data. . . . . . . . . . . . . . . . . . . 6-12
6.2.9 Exchanging Gauge Electronics . . . . . . . . . . . . . . . . 6-13
6.2.10 Calibration Using the WinSetup Calibrate function . 6-14
6.2.11 Loading the Default Database . . . . . . . . . . . . . . . . . 6-19
6.3 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20
6.3.1 Device Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
6.3.2 Warning Messages . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
6.3.3 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
6.3.4 Measurement Status . . . . . . . . . . . . . . . . . . . . . . . . 6-27
APPENDIX A
Reference Data
A.1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.2 Dimensional drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-4
A.3 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8
A.3.1 Transmitter Head (TH) . . . . . . . . . . . . . . . . . . . . . . . .A-8
A.3.2 Horn Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-9
A.3.3 Parabolic Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . .A-9
A.3.4 Still-pipe Array Antenna . . . . . . . . . . . . . . . . . . . . . .A-10
A.3.5 LPG/LNG Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . A-11
A.3.6 5900S Radar Level Gauge Options . . . . . . . . . . . . . A-11
APPENDIX B
Product Certifications
B.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
B.2 EU Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
B.3 Hazardous Locations Certifications . . . . . . . . . . . . . . . . . . . . . .B-3
B.3.1 Factory Mutual US Approvals . . . . . . . . . . . . . . . . . . B-3
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
TOC-3
Rosemount 5900 Series
Table of Contents
B.3.2 Factory Mutual Canadian Approvals . . . . . . . . . . . . .B-4
B.3.3 European ATEX Directive Information . . . . . . . . . . . . B-5
B.3.4 IECEx Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-6
B.4 Approval Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
APPENDIX C
Advanced Configuration
C.1 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-1
C.2 Winsetup Advanced Configuration . . . . . . . . . . . . . . . . . . . . . .C-3
C.3 Tank Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-4
C.4 Empty Tank Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-5
C.5 Surface Echo Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-9
C.6 Filter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-11
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
TOC-4 Table of Contents
Preliminary

Reference Manual
300520EN, Rev AA
November 2009 Rosemount 5900 Series
www.rosemount-tg.com
Section 1 Introduction
1.1 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-1
1.2 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-2
1.3 Manual Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-3
1.4 Service Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1-4
1.1 SAFETY
MESSAGES
Procedures and instructions in this manual may require special precautions to
ensure the safety of the personnel performing the operations. Information that
raises potential safety issues is indicated by a warning symbol ( ). Refer to
the safety messages listed at the beginning of each section before performing
an operation preceded by this symbol.
Failure to follow these installation guidelines could result in death or serious
injury:
• Make sure only qualified personnel perform the installation.
• Use the equipment only as specified in this manual. Failure to do so may
impair the protection provided by the equipment.
Explosions could result in death or serious injury:
• Verify that the operating environment of the transmitter is consistent with the
appropriate hazardous locations certifications.
• Before connecting a communicator in an explosive atmosphere, make sure the
instruments in the loop are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
• Do not remove the gauge cover in explosive atmospheres when the circuit is
alive.
Electrical shock could cause death or serious injury.
• Use extreme caution when making contact with the leads and terminals.
Any substitution of non-recognized parts may jeopardize safety. Repair, e.g. substitution
of components etc., may also jeopardize safety and is under no circumstances allowed.
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
1-2 Section 1. Introduction
1.2 SYMBOLS
The CE marking symbolises the conformity
of the product with the applicable European
Community Directives.
The EC-Type Examination Certificate is a
statement of a Notified Certification Body
declaring that this product meets the
Essential Health and Safety Requirements
of the ATEX directive
The FM APPROVED Mark indicates that the
equipment is approved by FM Approvals
according to applicable Approval Standards
and is applicable for installation in
hazardous locations
Protective Earth
Ground
External cabling must be approved for use in
min. 81°C
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
1-3
Rosemount 5900 Series
Section 1. Introduction
1.3 MANUAL
OVERVIEW
This manual provides installation, configuration, and maintenance information
for the Rosemount 5900 Series Radar Level Gauge.
Section 2: Overview
• Gauge components
• System overview
• Antenna types
• Installation procedure
Section 3: Installation
• Installation considerations
• Mechanical installation
• Electrical installation
Section 4: Configuration
• Basic configuration
• Configuration using TankMaster WinSetup
• LPG configuration
Section 5: Operation
• Viewing measurement data
• Alarm handling
Section 6: Service and Troubleshooting
• Serivce functions
• Troubleshooting
• Device and measurement status
• Error and warning codes
Appendix A: Reference Data
• Specifications
• Ordering Information
Appendix B: Product Certifications
• European ATEX Directive information
• FM approvals
• Labels
•Drawings
Appendix C: Advanced Configuration
•Tankscan
• Empty tank handling
• Surface echo tracking
• Filter settings
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
1-4 Section 1. Introduction
1.4 SERVICE SUPPORT To expedite the return process contact the nearest Emerson Process
Management/Rosemount Tank Gauging representative.
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
1-5
Rosemount 5900 Series
Section 1. Introduction
1.5 PRODUCT
RECYCLING/
DISPOSAL
Recycling of equipment and packaging should be taken into consideration
and disposed of in accordance with local and national legislation/regulations.
The label below is put on Rosemount Tank Gauging products as a
recommendation to customers if scrapping is considered.
Recycling or disposal should be done following instructions for correct
separation of materials when breaking up the units.
Figure 1-1. A green label is
placed on the housing of the
level gauge
1.6 PACKING
MATERIAL
Rosemount Tank Radar AB is fully certified according to ISO 14000
environmental standards. By recycling the plywood boxes material used for
shipping our products you can contribute to take care of the environment.
1.6.1 Reuse Experience has shown that NEFAB ExPak packaging can be used 4-5 times.
1.6.2 Recycling After careful disassembly the plywood sides may be reused. Metal waste may
be converted.
1.6.3 Energy recovery Products which have served their time may be divided into wood and metal
components and the wood can be used as fuel in sufficient ovens.
Due to its low moisture content (approximately 7%) this fuel has a higher
calorific value than ordinary wood fuel (moisture content approximately 20%).
When burning interior plywood the nitrogen in the adhesives may increase
emissions of nitrogen oxides to the air 3-4 times more than when burning bark
and splinter.
NOTE!
Landfill is not a recycling option and should be avoided.
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
1-6 Section 1. Introduction
Preliminary

Reference Manual
300520EN, Rev AA
November 2009 Rosemount 5900 Series
www.rosemount-tg.com
Section 2 Overview
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
2.2 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
2.3 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-3
2.4 Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-7
2.5 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . page 2-9
2.1 INTRODUCTION The Rosemount 5900 is a two-wire radar level gauge for high accuracy
non-contact measurements. The gauge continously emits a radar signal with
varying frequency towards the product surface. This allows very accurate
level measurements by processing the different frequencies between the
emitted and received radar signals.
The Rosemount 5900 is an integral part of the flexible Rosemount Raptor
system. The advanced and robust design makes it suitable for a vast range of
applications. It is capable of high accuracy level measurements as well as
handling obstacles that may interfere with measurement signals.
Figure 2-1. System integration
The Rosemount 5900 delivers measurement data and status information to a
Rosemount 2410 tank hub via the intrinsically safe Tankbus.
Data from a group of tanks is buffered by a 2160 Field Communication Unit
(FCU), and is distributed via the Group Bus to a TankMaster PC, or a host
system, whenever the FCU receives a request for data.
TankMaster
Rosemount 2410 Tank Hub
Modem
FCU 2160
Relay outputs
Secondary bus
Primary Bus
Intrinsically
safe Tankbus
Rosemount 5900 Rosemount 2240
Rosemount 2230
Group Bus
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
2-2 Section 2. Overview
2.2 COMPONENTS
Figure 2-2. Rosemount 5900
components
1. Terminal compartment
2. Cable entries
3. Flange
4. Antenna
5. Grounding terminal
6. Weather protection hood
7. Label
8. Transmitter head with signal processing electronics
22
1
4
6
58
3
7
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
2-3
Rosemount 5900 Series
Section 2. Overview
2.3 SYSTEM
OVERVIEW
Rosemount Raptor is a revolutionary, state-of-the art, inventory and custody
transfer radar tank level gauging system. It is developed for a wide range of
applications at refineries, tank farms and fuel depots, and fulfills the highest
requirements on performance and safety.
The Rosemount Raptor product portfolio includes a wide range of
components to build small or large customized tank gauging systems. The
system includes various devices, such as radar level gauges, temperature
transmitters, and pressure transmitters for complete inventory control. Such
systems are easily expanded thanks to the modular design.
Rosemount Raptor is a versatile system that is compatible with and can
emulate all major tank gauging systems. Moreover, the well-proven emulation
capability enables step-by-step modernization of a tank farm, from level
gauges to control room solutions.
It is possible to replace old mechanical or servo gauges with modern
Rosemount Raptor gauges, without replacing the control system or field
cabling. It is further possible to replace old HMI/SCADA-systems and field
communication devices without replacing the old gauges.
There is a distributed intelligence in the various system units which
continously collect and process measurement data and status information.
When a request for information is received an immediate response is sent
with updated information.
The field devices on the tank communicate over the intrinsically safe
Rosemount Raptor Tankbus. The Tankbus is based on a standardized
fieldbus, the FISCO(1) FOUNDATION™ fieldbus, and allows integration of any
device supporting that protocol. By utilizing a 2-wire field bus the power
consumtion is minimized. The standardized field bus also enables integration
of other vendors’ equipment on the tank.
The flexible Rosemount Raptor system supports several combinations to
achieve redundancy, from control room to the different field devices.
Redundant network configuration can be achived at all levels by doubling
each unit and using multiple control room work stations.
(1) See reference document IEC/TS 60079-27
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
2-4 Section 2. Overview
Figure 2-3. Raptor system
architecture
Rosemount 2230
Graphical Field
Display
Rosemount 2240
Multi-input Temperature
Transmitter
Rosemount 5900
Radar Level Gauge
Raptor Tankbus
Rosemount 2410
Tank Hub
Intrinsically safe Tankbus
Rosemount 5300
Level Transmitter
2240
Rosemount 5400
Radar Level
Transmitter
Rosemount 5900
Rosemount 3051S
Pressure Transmitter
TRL2 Modbus
/ 485 Modbus
Group bus
Field Bus
Modem
Rosemount 2160
Field Communication Unit
TankMaster PC
Plant Host
Computer 644
644
644
Rosemount 644
Temperature
Transmitter
TankMaster PC
Plant Host
Computer
Non-Hazardous area Hazardous area
Rosemount 2410
Tank Hub
Rosemount 2410
Tank Hub
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
2-5
Rosemount 5900 Series
Section 2. Overview
TankMaster HMI Software
TankMaster is a powerful Windows-based Human Machine Interface (HMI) for
complete tank inventory management. It provides configuration, service,
set-up, inventory, and custody transfer functions for Rosemount Raptor
systems and other supported instruments.
TankMaster is designed to be used in the Microsoft®Windows XP and Vista
environment providing easy access to measurement data from your Local
Area Network.
The TankMaster WinOpi program lets the operator monitor measured tank
data. It includes alarm handling, batch reports, automatic report handling,
historical data sampling as well as inventory calculations such as Volume,
Observed Density and other parameters. A plant host computer can be
connected for further processing of data.
The TankMaster WinSetup program is a graphical user interface for
installation, configuration and service of the different devices in the
Rosemount Raptor system.
Rosemount 2160 Field Communication Unit
The 2160 field communication unit (FCU) is a data concentrator that
continuously polls and stores data from field devices such as radar level
gauges and temperature transmitters in a buffer memory. Whenever a request
for data is received, the FCU can immediately send data from a group of tanks
from the updated buffer memory.
Rosemount 2410 Tank Hub
The Rosemount 2410 tank hub acts as a power supply to the connected field
devices in the hazardous area using the intrinsically safe Raptor Tankbus.
The Rosemount 2410 tank hub collects measurement data and status
information from field devices on a tank. It has two external buses for
communication with various host systems.
Rosemount 5900 Radar Level Gauge
The Rosemount 5900 radar level gauge is an intelligent instrument for
measuring the product level inside a tank. Different antennas can be used in
order to meet the requirements of different applications. The 5900 can
measure the level of almost any product, including bitumen, crude oil, refined
products, aggressive chemicals, LPG and LNG.
The Rosemount 5900 sends microwaves towards the surface of the product
in the tank. The level is calculated based on the echo from the surface. No
part of the 5900 is in actual contact with the product in the tank, and the
antenna is the only part of the gauge that is exposed to the tank atmosphere.
The 5900 2-in-1 option makes the radar level gauge redundant to electric
circuit failure. Two separate radar units in the same transmitter head allows
two independent level measurements using one antenna.
Preliminary

Reference Manual
300520EN, Rev AA
November 2009
Rosemount 5900 Series
2-6 Section 2. Overview
Rosemount 2240 Multi-Input Temperature Transmitter
The Rosemount 2240 multi-input temperature transmitter can connect up to
16 temperature spot sensors and an integrated water level sensor.
Rosemount 2230 Graphical Field Display
The Rosemount 2230 graphical field display presents inventory tank gauging
data such as level, temperature, and pressure. The four softkeys allow you to
navigate through the different menus to provide all tank data, directly in the
field. The Rosemount 2230 supports up to 10 tanks.
Rosemount 644 Temperature Transmitter
The Rosemount 644 is used with single spot temperature sensors.
Rosemount 3051S Pressure Transmitter
The 3051S series consists of transmitters and flanges suitable for all kinds of
applications, including crude oil tanks, pressurized tanks and tanks with /
without floating roofs.
When a radar level gauge is connected to a pressure transmitter near the
bottom of the tank, the density of the product can be calculated and
presented. One or more pressure transmitters with different scalings can be
used on the same tank to measure vapor and liquid pressure.
Rosemount 2180 Field Bus Modem
The Rosemount 2180 field bus modem (FBM) is used for connecting a
TankMaster PC to the TRL/2 communication bus. The 2180 is connected to
the PC using either the RS232 or the USB interface.
Preliminary