Emerson ASCO 7000 Series User manual

381333–202 C
50 Hanover Road, Florham Park, New Jersey 07932–1591 USA
For sales or service call 1 800 800–2726 (ASCO) www.ascopower.com
ASCO POWER TECHNOLOGIES CANADA PO Box 1238, 17 Airport Road, Brantford, Ontario, Canada N3T 5T3
telephone [phone], fax [phone], for service call 1 888 234–2726 (ASCO) www.asco.ca
Operator’s
Manual
7000 Series ATS
Automatic Transfer Switches
H–design 600 through 1200 amps
TABLE OF CONTENTS
section-page
INSTALLATION 1-1........................
Mounting and Line Connections 1-1.........
Auxiliary Circuits and Harness 1-2...........
Engine Starting Contacts 1-2...............
Functional Test 1-2, 1-3, 1-4, 1-5.............
TESTING & SERVICE 2-1..................
Transfer Test 2-1..........................
Preventive Maintenance 2-1................
Disconnecting the Controller 2-1............
Manual Load Transfer 2-2..................
Trouble-Shooting 2-2......................
INDEX back cover.........................
Note: Refer to the outline and wiring drawings
provided with your 7000 Series ATS for all
installation and connection details and accessories.
An experienced licensed electrician must install the ATS.
600---1000 amp. size
DANGER is used in this manual to warn of high
voltages capable of causing shock, burns, or death.
WARNINGisusedinthismanualtowarn
of possible personal injury.
CAUTIONisusedinthismanualtowarn
of possible equipment damage.
Refer to Group 5 Controller User’s Guide 381333–126
for ATS status display messages, time delays, pickup
& dropout settings, and adjustments.
1200 amp. size
Cross Reference RA Part Number PP2491

Rating Label
Each Automatic Transfer Switch contains a rating label to
define the loads and fault circuit withstand/closing ratings.
Refer to the label on the Transfer Switch for specific values.
Do not exceed the values on the rating label.
Exceeding the rating can cause personal injury
or serious equipment damage.
Nameplate
The Transfer Switch nameplate includes data for each
specific 7000 Series ATS. Use the switch only within the
limits shown on this nameplate. A typical Catalog Number
is shown below with its elements explained.
Catalog Number Identification
Typical 7000 Series ATS catalog no. for overlapping
neutral, 3 pole, 600 amp, 480 V, ATS in Type 1 enclosure:
H7ATS C 3 600 N 5 C
Phase Poles
Neutral
A–solid
C– overlapping
Amperes Voltage Controller Enclosure
B–switched 5X –if
accessories
ordered
5–standard
G–type4 *
C–type1
F–type3R
L–type12 *
3–threeØ
2–singleØ
D220
C208
E230
K415
M460
J400
L440
N480
G277
F240
H380 Q575
P550
R600
1200
1000
800
blank – none
blank – open type
600
* available 600–1000 amp. sizes only
Transfer
Switch
power
connections
Group 5
Controller
Transfer
Control
&lights
600–1000 amp. size in typical enclosure with location of customer connections
power
connections
field connections
terminal block TB
ground lug
ground lug
A
800

Transfer
Switch
power
connections
Group 5
Controller
Transfer
Control
&lights
1200 amp. size in typical enclosure with location of customer connections
power
connections
field connections
terminal block TB ground lug

SECTION 1 INSTALLATION
1 --- 1
ASCO 7000 Series Automatic Transfer Switches (ATSs)
are factory wired and tested. Field installation requires
requires mounting and connection of service cables, and
auxiliary control circuits (if required).
Remove the Shipping Skid (large ATSs)
For large ATSs, open the front door and remove the four
lag screws (2 in front, 2 in rear) securing enclosure to the
wood skid.
Supporting Foundation
The supporting foundation for the enclosure must be
level and straight. Refer to the applicable enclosure
outline drawing included with the switch for all mounting
details including door opening space.
If bottom cable entry is used, the foundation must be
prepared so that the conduit stubs are located correctly.
Refer to the enclosure outline drawing for specified area
and location. Provide cable bending space and clearance
to live metal parts. When a concrete floor is poured, use
interlocking conduit spacer caps or a wood or metal
template to maintain proper conduit alignment.
Mounting
Refer to the applicable enclosure outline drawing fur-
nished with this switch and mount the automatic transfer
switch according to details and instructions shown on
diagram.
Line Connections
Refer to the Wiring Diagram provided with the switch.
All wiring must be made in accordance with the National
Electrical Code and local codes.
It is not necessary to remove pole covers from the
transfer switch for cabling. If you do remove them,
reinstall them carefully.
De–energize the conductors before making any
line or auxiliary circuitry connections. Be sure
that Normal and Emergency line connections
are in proper phase rotation. Place engine gen-
erator starting control in the OFF position. Make
sure engine generator is not in operation.
Testing Power Conductors
Do not connect the power conductors to the transfer
switch until they are tested. Installing power cables in
conduit, cable troughs and ceiling-suspended hangers
often requires considerable force. The pulling of cables
can damage insulation and stretch or break the
conductor’s strands. For this reason, after the cables are
pulled into position, and before they are connected, they
should be tested to verify that they are not defective or
have been damaged during installation.
Protect the switch from construction grit
and metal chips to prevent malfunction or
shortened life of the automatic switch switch.
Connecting Power Conductors
After the power cables have been tested, connect them to
the appropriate terminal lugs on the transfer switch as
shown on the wiring diagram provided with the switch.
Make sure the lugs provided are suitable for use with the
cables being installed. Standard terminal lugs are solder-
lessscrewtypeandwillacceptthewiresizeslistedonthe
drawings provided with the switch. Be careful when
stripping insulation from the cables; avoid nicking or
ringing the conductor. Remove surface oxides from
cables by cleaning with a wire brush. When aluminum
cable is used, apply joint compound to conductors.
Tighten cable lugs to the torque specified on rating label.
Controller Ground
A grounding wire must be connected to the controller’s
lower left mounting stud. Because the controller is
mounted on the enclosure door, a conductive strap must
be used between the enclosure and the door. This
connection provides proper grounding which does not
rely upon the door hinges.
Harnesses
The transfer switch is connected to the left side of the
controller by a plug–in harness (two plugs).

INSTALLATION (continued)
1 --- 2
Engine Starting Contacts
All customer connections, including the engine control
contact connections, are located on terminal block TB
which is mounted on the top right side of the enclosure.
Refer to the wiring diagram provided with the automatic
transfer switch and connect the engine start wires to the
appropriate terminals. See Figure 1–1 and Table A.
Table A. Engine start connections.
When normal source
fails
Te r m i n a l s o n
Te r m i n a l B l o c k T B
contact closes TB1 and TB2
contact opens TB1 and TB3
Note: To temporarily disable engine control from
the automatic transfer switch you can unplug J3
from the small P3 receptacle at the bottom of the
assembly. BesuretoreconnectplugJ3totheP3
receptacle for automatic transfer switch operation.
Auxiliary Circuits
Connect auxiliary circuit wires to appropriate terminals
on transfer switch terminal block TB as shown on the
wiring diagram provided with this automatic transfer
switch.
engine start
connections
on
customer
terminal
block TB
Figure 1-1. Customer terminal block on the top right
side of the enclosure.
Functional Test
The Functional Test consists of three checks:
❐1 — Manual Operation Test, page 1–3
❐2—VoltageChecks,page1–4
❐3 — Electrical Operation, page 1–5
Do these checks in the order presented
to avoid damaging the ATS.
Read all instructions on the Wiring Diagram and labels
affixed to the automatic transfer switch. Note the control
features that are provided and review their operation
before proceeding.
Continue to 1–ManualOperationTest on next page.

INSTALLATION (continued)
1 --- 3
1 – Manual Operation Test
A detachable maintenance handle is provided on the frame
of the Transfer Switch for maintenance purposes only.
Manual operation of the transfer switch should be
checked before it is energized (operated electrically).
Do not manually operate the transfer switch
until both power sources are disconnected:
open both circuit breakers.
1. After deenergizing both power sources, open the
enclosure door. Locate and remove the mainte-
nance handle from the clips on the left side of the
transfer switch frame. Insert the handle into the hole
in the molded hub on the left side of the operator.
See Figures 1–3 and 1–4 and Table B.
2. Move the maintenance handle up or down as shown to
manually operate the transfer switch. It should operate
smoothly without any binding. If it does not, check for
shipping damage or construction debris.
3. Return the transfer switch to the Normal position.
Observe that the window indicators (right side) show
the top shaft O (open) and the bottom shaft C (closed).
Table B. Maintenance handle positions.
ATS Position Handle Indicators
Normal
E
N
up E=O
upper contacts open
N=C
lower contacts closed
Emergency
E
Ndown
E=C
upper contacts closed
N=O
lower contacts open
Note: If Normal and Emergency connections are
reversed this operation is also reversed.
maintenance
handle
left side of
transfer switch
storage clips
Figure 1-2. Maintenance handle and its storage clips.
4. Remove the maintenance handle and store it on the
frame (left side) in the clips provided.
Verify that the maintenance handle
has been removed before proceeding!
Now continue to 2–VoltageCheckson next page.
handle
hub
UP closes the
Normal source
contacts (lower)
DOWN closes the
Emergency source
contacts (upper)
frame
window
indicators
Ois open
Cis closed
Emergency
contacts
Normal
contacts
contact position
indicators (right side)
Figure 1-3. Maintenance handle operation and contact position indicators.

INSTALLATION (continued)
1 --- 4
RED
RED
GREEN
GREEN
observe
these lights
Figure 1-4. Standard controls and indicators.
2–VoltageChecks
First check nameplate on transfer switch; rated voltage
mustbethesameasnormalandemergencylinevoltages.
Verify that the feeders have been
connected to the proper lugs.
Useextremecautionwhenusingameter
to measure voltages. Do not touch power
terminals; shock, burns, or death could result !
Perform steps 1 through 6 at the right. Observe the status
lights. See Figure 1–4.
■Black square means light is on.
❐White square means light is off.
* If necessary, adjust voltage regulator on the generator
according to the manufacturer’s recommendations. The
Automatic Transfer Switch will respond only to the rated
voltage specified on the Transfer Switch nameplate.
Note
Refer to Section 3 of Group 5 Controller User’s Guide
381333–126 for how to display the Status of the ATS and
the Voltage and Frequency of each source.
Now continue to 3 – Electrical Operation on next page.
1
Close the normal source circuit
breaker. The Transfer Switch
Connected To Normal and the
Normal Source Accepted lights
should come on.
2
Use an accurate voltmeter to
check phase to phase and
phase to neutral voltages pres-
entatthetransferswitchnormal
source terminals.
3
Close the emergency source
circuit breaker. (Start generator,
if necessary.) The Transfer
Switch Connected To Normal &
Emergency Source Accepted
lights should come on.
4
Use an accurate voltmeter to
check phase to phase and
phase to neutral voltages pres-
ent at the transfer switch emer-
gency source terminals.*
5
Useaphaserotationmeterto
check phase rotation of emer-
gency source; it must be the
same as the normal source.
ABC
6
Shut down the engine–genera-
tor, if applicable. The Emergen-
cy Source Accepted light should
go off. Then put the starting
control selector switch (on the
generator set) in the automatic
position. Close enclosure door.

INSTALLATION (continued)
1 --- 5
RED
RED
GREEN
GREEN
observe
these lights
operate
this switch
Figure 1-5. Standard controls and indicators.
3 – Electrical Operation
This procedure will check the electrical operation of the
Automatic Transfer Switch. See Figure 1–5.
Be sure to close the enclosure door
before proceeding to prevent personal injury
in case of electrical system fault.
Transfer Test
Both normal and emergency sources must be available
and the emergency source generator (if used) must be
capable of being started in this procedure.
Perform steps 1 through 5 at the right. Observe the status
lights.
■Black square means light is on.
❐White square means light is off.
This completes the Functional Test of the ATS.
1
The Transfer Switch Connected
To Normal and Normal Source
Accepted lights should be on.
2
Turn and hold Transf er Co ntrol
switch clockwise to Transfer
Test until the engine starts
and runs (within 15 sec.).
Emergency Source Accepted
light should come on.
3
Transfer switch will operate to
the Emergency position after
Feature2Btimedelay.The
Transfer Switch Connected To
Emergency light should come
on and Load Connected to Nor-
mal light goes off.
4
Transfer switch will operate
back to Normal position after
Feature3Atimedelay.Forim-
mediate retransfer turn Tra nsf er
Control counterclockwise to
Retransfer Delay Bypass.The
Transfer Switch Connected To
Normal light should come on;
Transfer Switch Connected to
Emergency light should go off.
5
The engine–generator will stop
after the Feature 2E time delay
(unloaded running engine cool-
down). The Emergency Source
Accepted light should go off.

SECTION 2 TESTING & SERVICE
2--1
TRANSFER TEST
Operate the 7000 Series ATS at least once a month by
following the five–step Electrical Operation Transfer
Tes t procedure on page 1–5.
PREVENTIVE MAINTENANCE
Reasonable care in preventive maintenance will insure
high reliability and long life for the 7000 Series ATS. An
annual preventive maintenance program is recom-
mended.
In the United States, ASCO Services, Inc. (ASI) is
ASCO Power Technologies’s national service
organization. ASI can be contacted at
1-800-800-2726 (ASCO) for information on
preventive maintenance agreements.
In Canada, for service call 1-800-234-2726 (ASCO).
Checklist for Yearly Inspection
Hazardous voltage capable of causing shock,
burns, or death is used in this switch.
Deenergize both Normal – Emergency power
sources before performing inspections!
❐Clean the ATS enclosure.Brush and vacuum away
any excessive dust accumulation. Remove any
moisture with a clean cloth.
❐Check the transfer switch contacts.Removethe
transfer switch barriers and check contact condition.
Replace the contacts if they become pitted or worn
excessively. Reinstall the barriers carefully.
❐Maintain transfer switch lubrication.Ifthe
transfer switch is subjected to severe dust or
abnormal operating conditions, renew factory
lubrication on all movements and linkages.
Relubricate the solenoid operator if the TS coil is
replaced. Do not use oil; order lubrication kit 75-100.
❐Check all cable connections & retighten them.
REPLACEMENT PARTS
Replacement parts are available in kit form. When or-
dering parts provide the Serial No., Bill of Material No.
(BOM), and Catalog No. from the transfer switch name-
plate. Contact your local ASCO Power Technologies
Sales Office or ASI:
in United States call 1 800 – 800 – ASCO (2726)
or in Canada call 1 800 – 234 – ASCO (2726)
DISCONNECTING THE CONTROLLER
The harness disconnect plugs are furnished for repair
purposes only and should not have to be unplugged. If
the controller must be isolated, follow these steps:
Disconnecting the Plugs
Do not unplug the controller
until steps 1a or 1b is completed.
1. Observe the position of the transfer switch.
a. If the transfer switch is in the Normal position, first
place standby engine starting control in the off
position. Second, then open the emergency source
circuit breaker. Third, open the normal source
circuit breaker.
b. If the transfer switch is in the Emergency position,
first open the normal source circuit breaker. Sec-
ond, place the engine starting control in the test
or run position. Third, open the emergency source
circuit breaker.
2. Separate the two quick disconnect plugs by squeez-
ing the latches. Do not pull on the harness wires.
Reconnecting the Plugs
Do not unplug the controller
until steps 1a or 1b is completed.
1. Observe the position of the transfer switch.
a. If the transfer switch is in the Normal position,
firstbesurethatbothnormal and emergency
source circuit breakers are open. Second, be sure
that the standby engine starting control is still in
the off position.
b. If the transfer switch is in the Emergency position,
firstbesurethatbothnormal and emergency
source circuit breakers are open.
2. The two harness plugs and sockets are keyed. Care-
fully align the plugs with the sockets and press
straight in until both latches click. Close the door!
3. Restore the two sources in sequence as follows:
a. If the transfer switch is in the Normal position,
first close the normal source circuit breaker.
Second, close the emergency source circuit break-
er. Third, place the standby engine starting
control in the automatic position.
b. If the transfer switch is in the Emergency position,
first close the emergency source circuit breaker.
Second close the normal source circuit breaker.

TESTING & SERVICE (continued)
2--2
MANUAL LOAD TRANSFER
This procedure will manually transfer the load if the
controller is disconnected.
Do not manually operate the transfer switch
until both power sources are disconnected
(all conductors deenergized).
1. Deenergize both the normal and emergency source
conductors (remove fuses or open circuit breakers).
2. Use the maintenance handle to manually operate the
transfer switch to the opposite source. See Manual
Operation on page 1–3.
3. Then remove the maintenance handle. See page 1–3.
Verify that the maintenance handle
has been removed before proceeding!
4. If the transfer switch is in the Emergency position
manually start the engine generator and then install
emergencysourcefuseorclosethecircuitbreaker.
TROUBLE-SHOOTING
Note any optional accessories that may be furnished on
the automatic transfer switch (ATS) and review their
operation. Refer to any separate drawings and/or
instructions that may be packed with the ATS. Hazardous voltage capable of causing shock,
burns, or death is used in this switch.
Do not touch the power or load terminals
of the transfer switch!
Table 2-1. Trouble-Shooting Checks.
CHECK IN NUMERICAL SEQUENCE
PROBLEM 1
OPERATION
2
GEN-SET
3
VOLTAGE
Engine–generator set does
not start when the Transfer
Control switch is turned and
held in Transfer Test position
or when the normal source
fails.
Hold Transfer Test switch 15
seconds or the outage must
be long enough to allow for
Feature1Ctimedelayplus
engine cranking and starting
time.
Starting control must be in the
automatic position. Batteries
must be charged and
connected. Check wiring to
engine starting contacts on
customer terminal block TB.
Verify that the small plug J3 is
connected to receptacle P3.
–
Transfer switch does not
transfer the load to the
emergency source after the
engine–generator set starts.
Wait for Feature 2B time delay
to time out (if used).
Generator output circuit
breaker must be closed.
Generator frequency must be
at least 95% of nominal
(57Hzfora60Hzsystem.)*
Voltmeter should read at least
90% of nominal phase to
phase voltage between
transfer switch terminals EA
and EC (or EL1 and EL2 for 2
pole switches). *
Transfer switch does not
transfer the load to normal
source when normal returns
or when the Transfer Control
switch is released.
Wait for Feature 3A time delay
to time out (if used).
–
Voltmeter should read at least
90% of nominal phase to
phase voltage between
transfer switch terminals NB
and NC, NC and NA, and NA
and NB (or NL1 and NL2 for 2
pole switches).
Engine–generator-set does
not stop after load retransfer
to the normal source.
Wait for Feature 2E time delay
to time out (if used).
Starting control must be in the
automatic position. –
* These are factory settings. Refer to the Group 5 Controller User’s Guide.
If the problem is isolated to circuits on the controller or the transfer switch, call your local ASCO Power Technologies
sales office or ASI. In the United States, call 1–800–800–2726. In Canada, call 1–800–234–2726. Furnish the Serial No.
and Catalog No. from the transfer switch nameplate.

INDEX
Printed in U.S.A. Copyright 2007 ASCO Power Technologies, L.P.
A
auxiliary circuits, 1–2
C
cable
lugs, 1–1
preparation, 1–1
catalog number, inside cover
cleaning, 2–1
connections
line, 1–1
contact position indicators, 1–3
controller, 1–1
disconnecting, 2–1
see Controller User’s Guide
grounding, 1–1
E
electrical operation, 1–5
Emergency Source Accepted light,
1–4, 1–5
engine starting contacts, 1–2
F
frequency, generator, 2–2
functional test, 1–2, 1–3, 1–4, 1–5
G
ground, controller, 1–1
ground lugs, inside front cover
H
harness, 1–1
disconnect plugs, 2–1
HELP
[e-mail]
800–800–ASCO
I
inspection, 2–1
installation, 1–1
indicators, contact position, 1–3
L
labels,
field terminal block TB, 1–2
rating, inside front cover
lights, 1–4, 1–5
lubrication, 2–1
M
maintenance handle, 1–3
illustration of, 1–3
warning, 1–3
maintenance, preventive, 2–1
manual load transfer, 2–2
warning, 2–2
manual operation, 1–3
illustration of, 1–3
warning, 1–3
N
nameplate, inside cover
Normal Source Accepted light, 1–4
O
operation
electrical, 1–5
manual, 1–3
illustration of, 1–3
warning, 1–3
optional accessories
see Controller User’s Guide
P
parts, 2–1
phase rotation check, 1–4
problem, 2–2
R
rating label, inside cover
replacement parts, 2–1
S
settings
see Controller User’s Guide
T
test, functional, 1–2, 1–3, 1–4, 1–5
time delays, 1–5, 2–2
see Controller User’s Guide
Transfer Control selector switch
Retransfer Delay Bypass, 1–5
Transfer Test, 1–5
Transfer Switch Connected To
Emergency light, 1–4, 1–5
Transfer Switch Connected To
Normal light, 1–4, 1–5
transfer test, 1–5, 2–1
transfer to emergency, 1–5
transfer to normal, 1–5
trouble–shooting, 2–2
V
voltage checks, 1–4
voltage, pickup and dropout settings
see Controller User’s Guide