Emerson Liebert itON 1500VA User manual

1 10H52200GM60 – Rev. 5 – 06/2014
Liebert®itON
Quick-Start Guide – 1500VA/2000VA, 230V
1BIMPORTANT SAFETY INSTRUCTIONS
Read SAFETY INSTRUCTIONS sheet first.
SETUP
4BStep 1
Inspect the Package
Inspect the package and the UPS upon receipt.
Notify the carrier and dealer of visible damage.
 
UPS Quick-start Safety Quick-start guide USB cable Input Cable
guide Instructions (all languages)
5BStep 2
Decide Where to Place the UPS
The UPS must be placed indoors, protected from
water, direct sunlight and excessive heat.
Provide at least 7.8” (20 cm) of clearance on all
sides of the unit for proper ventilation.
6BStep 3
Charge the UPS Battery Before Use
The UPS battery is fully charged before shipping.
However, some charge may be lost during shipping
and the battery should be recharged prior to use.
Plug in the AC input cord (supplied) to the wall
outlet. For the best results, suggest to charge
the battery at least 6 hours before initial use.
The unit charges its battery while connecting
to the utility.
7BStep 4
Start the UPS
After the battery is fully charged:
Turn on the UPS by pressing the On/Off
button.
LED1 should be illuminated (green), indicating the
UPS is operating in Normal mode.
8BStep 5
Connect the Loads
The UPS has six battery backup outlets that provide
power when the UPS operates on battery. (see
Figure 2 on next page)
Plug the loads into the battery backup outlets
on the rear of the UPS.
CAUTION: NEVER connects a laser printer or
scanner to the UPS unit. This may cause the damage
of the unit.
Step 6
Connect the Network Surge Protection
The UPS has two RJ-11 jacks for network lines.
Connect a single-line network cable into the
RJ-11 network surge protection IN jack on the
rear of the UPS.
Connect a RJ-11 cable from the OUT jack on
the rear panel of the UPS to a port on a PC or
network device such as a router.
Step 7
Set Up Shutdown Software
To start using shutdown software:
Install the shutdown software on supplied CD.
Follow on screen instructions to install the
software.
Connect one end of USB cable (supplied) to
the USB port on the rear panel of the UPS.
Connect the other end of USB cable on the
computer USB port.
See the software user manual for detailed
operation inside of supplied CD.



All manuals and user guides at all-guides.com
all-guides.com

10H52200GM60 – Rev. 5 – 06/2014 2
10BUPS CONTROLS AND CONNECTIONS
Figures 1 – Front Panel LEDs

Figure 2 – Rear Panel
UPS Status, Alarm Conditions and Alerts
Condition LED Color Solid/Flashing Audible Alarm
Normal mode LED 1 Green Solid (none)
Battery mode LED 1 Green Flashes Every 10 seconds
Load level at Normal mode LED 3-6 Green Solid Overload: every 0.5 second
Battery level at Battery mode LED 3-6 Green Solid Low battery: every second
Fault LED 2 Red Solid Continuous until UPS shuts down
Battery replacement LED 2 Red Solid Every 2 seconds

9BTROUBLESHOOTING
If the UPS malfunctions during operation, check the following chart for proper adjustment. For further assistance, please contact your local
Emerson Network Power representative.
Problem Possible Causes Solutions
Utility is normal, but LED is not
illuminated.
Battery capacity may be low.
The UPS battery reached end of life.
The UPS may not be turned on.
Recharge the UPS at least 6 hours.
Properly trained and qualified service personnel
replace the battery with the same type of
battery ,do not attempt to replace the battery
yourself.
Press the On/Off button to turn on the UPS.
Alarm buzzer beeps continuously
although utility power is normal.
The UPS may be overloaded. Disconnect some equipment from the UPS.
UPS does not provide expected
backup time.
The UPS may be overloaded
Battery voltage may be low.
The UPS battery reached end of life.
Disconnect some equipment from the UPS.
Recharge the UPS at least 6 hours.
Properly trained and qualified service personnel
replace the battery with the same type of
battery ,do not attempt to replace the battery
yourself.
Utility is normal, but UPS status
LED flashes.
The power cord may not be
connected properly.
Connect the power cord securely into a wall outlet.

3BSPECIFICATIONS
Model Liebert itON 1500 Liebert itON 2000
Capacity (VA/W) 1500/900 2000/1200
Net Weight, lb. (kg) 24 (11.1) 25 (11.5)
Dimensions – W x D x H (mm) 146 x 391 x 205
Line Input Nominal Voltage 220 - 240VAC
Line Input Voltage Range ** 170 - 280VAC
Line Frequency 50Hz / 60Hz (auto sensing)
Output Voltage (Utility Power Normal) 230VAC
Output Voltage (Battery Operation) ±10%
On-Battery Wave Form Stepped sinewave
Battery Type – VDC x Ah x Quantity 12V x 9 Ah x 2 12V x 9 Ah x 2
Typical Recharge Time 4 hours to 90%
Battery Run Time* – Half Load 5 minutes 3 min 10 Sec
Operating Temperature, °F (°C) 32 to 104 (0 to 40)
Storage Temperature, °F (°C) -4 to 122 (-20 to 50)
Operating /Storage Relative Humidity 0 – 90%, non-condensing

*Battery run time may vary depending on load. ** Depending of output load.
Emerson and Business-Critical Continuity are trademarks of Emerson Electric Co. or one of its affiliated companies.
©2005 Emerson Electric Co.
Battery backup
outlets
(3 x IEC C13)
LED 1
(status)
LED 3-6
(
Load/Batter
y
level
)
On/Off button
LED 2 (fault)
USB interface
Battery backup
outlets
(3 x Schuko)
AC mains inlet
& fuse
RJ-11 jacks (2)
Network surge
protection
All manuals and user guides at all-guides.com