Emerson Liebert PSP500MT3-230U User manual

Liebert®PSP™
Quick-Start Guide - 500VA/650VA, 230V
IMPORTANT SAFETY INSTRUCTIONS
• Do not connect equipment that may overload the UPS or demand half-wave
rectification, such as a laser printer.
• Connect the UPS only to an earthed / grounded socket that meets electrical safety
guidelines.
• Locate the UPS near a wall socket. Do not use an extension cord between the UPS and
the socket.
• Use CE-marked cables only for connections between mains, the UPS and equipment.
• The Liebert PSP has been designed for small office/home office use only; it is NOT
recommended for use in life-support applications.
• In the event of an emergency, press the On/Off button and disconnect the power cord
from the AC mains to properly disable the UPS.
• Do not attach power strips or surge suppressors to the UPS.
• Do not attempt to service any parts inside the UPS except when replacing the batteries.
Failure to adhere to this could cause personal injury or equipment malfunction and void
the warranty.
• This unit uses components that are dangerous for the environment, such as electronic
cards and other electronic components. Any component that is removed must be taken
to specialized collection and disposal centers. If this unit must be dismantled, this must
be done by specialized personnel who are properly trained and qualified. The unit must
be taken to a center specialized in collection and disposal of dangerous substances.
• For technical support:
• Visit www.liebert.com or
• Send an e-mail to [e-mail].
SETUP
UPS CONTROLS AND CONNECTIONS
Step 1 Inspect the Package
Inspect the package and the UPS upon receipt.
Notify the carrier and dealer of visible damage.
The package includes:
• Liebert PSP
• USB cable
• Quick-start guide
• 2 IEC output cables
The Liebert MultiLink™ software may be
downloaded from the Liebert Web site at:
multilink.liebert.com
See Step 7 for installation instructions.
Step 2 Decide Where to Place the UPS
The UPS must be placed indoors, protected from water, direct
sunlight and excessive heat.
Provide at least 100mm (4") of clearance on all sides of the unit
for proper ventilation.
Step 3 Charge the UPS Battery Before Use
The UPS battery is not charged before shipping. It MUST be charged before use.
• Use the input power cord from computer equipment as the input power cord of UPS.
Connect a user-supplied power cord from the UPS to a wall socket and charge for at
least eight hours. Unit can be charged in the on or off state.
Note: If battery is placed in storage, charge the battery every six months if kept at
-15°C to +29°C (5°F to 85°F)—or every three months if kept at 30°C (86°F) or higher.
Step 4 Start the UPS
After the battery is fully charged:
• Turn on the UPS by pressing the On/Off button (see Figure 1 below).
LED 1 should be illuminated (green), indicating the UPS is operating in Normal Mode.
Step 5 Connect the Loads
The UPS has three battery backup sockets that
provide power when the UPS operates on bat-
tery. There is also one surge-only socket (see
Figure 2 below).
• Plug the loads into the battery backup
sockets on the rear of the UPS.
Caution: Do not connect a laser printer to the
UPS.
Step 6 Connect the Network Surge Protection
The UPS has two network cable jacks for network lines
(see Figure 2 below).
• Connect a single-line network cable into the network
surge protection IN jack on the rear of the UPS.
• Connect a network cable from the OUT jack on the
rear of the UPS to a port on a PC or network device
such as a router.
Step 7 Set Up Liebert MultiLink software
To start using the Liebert MultiLink software:
• Install the software.
See the Liebert MultiLink quick-start guide or user manual
for installation instructions.
• Connect one end of the USB cable (supplied) to the USB
port on the rear of the UPS. Connect the other end to a
USB port on the computer.
See the Liebert MultiLink user manual for operating instructions.
Note: Emerson recommends connecting the USB cable directly to the computer
WITHOUT using a USB hub.
USB
cable
Quick-
start
guide
UPS
2 IEC
output
cables
!
EMERSON
™
Network Power
Liebert®PSP
AC Power System
UPS Status, Alarm Conditions and Alerts
Condition LED Color Solid/Flashing Audible Alarm
Normal Mode LED 1 Green Solid (steady glow) (None)
Battery Mode LED 1 Green Flashes every 3 seconds Every 3 seconds
Battery Low LED 1 Green Flashes every 1 second till end of discharge (EOD) Every 1 second
Overload LED 2 Amber Solid (steady glow) until load drops or breaker trips Continuous
Battery Replacement LED 2 Red Flashes every 1 second for 5 seconds only Every 1 second for 5 seconds only
Fault LED 2 Red Solid (steady glow) until UPS shuts down after 5 seconds Continuous until UPS shuts down
Figure 2 - Rear Panel
AC mains
inlet
Figure 1 - Front Panel LEDs
Battery backup
sockets (3)
IEC 320 C13
RJ-45 jacks (2)
Network
protection USB
interface
Surge socket (1)
IEC 320 C13
Mains
breaker
LED 2 (red = fault;
amber = overload)
Fault
symbol
Overload
symbol
Mains
symbol
On/Off button
LED 1
(green)

© 2009 Liebert Corporation All rights reserved throughout the
world. Specifications subject to change without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks or registered trademarks
of their respective owners.
SLI-23285_REV0_03-09
Technical Support / Service
800-222-5877
(Outside U.S. 614-841-6755)
[email protected]
Web site: www.liebert.com
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
[phone]
Fax: [phone]
Asia
7/F Dah Sing Financial Centre
108 Gloucester Road
Wanchai, Hong Kong
852 2572 2201
Fax: [phone]
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
REPLACING THE BATTERY
Servicing of batteries should be performed or supervised by personnel knowledgeable about batteries and required precautions.
When replacing batteries, replace with the same type and size battery.
To replace the battery:
1. Turn off all connected loads, then turn off the UPS and unplug the input
power cord. (Batteries are NOT hot-swappable.)
2. Carefully lay the UPS on its left side, as shown in the diagram.
3. Use a #1 Phillips head screwdriver to remove the four screws from the
right-side cover, then pull up the right-side cover and remove it.
4. Remove the black wire from the negative (-) terminal and the red wire from
the positive (+) terminal.
5. Gently remove the battery from the UPS.
Attention: Risk of Electric Shock.
6. Verify that the replacement battery matches the dimensions and battery
specifications.
7. Connect the battery leads to the new battery. Be sure to reconnect the red
wire to the positive (+) terminal and the black wire to the negative (-)
terminal.
Note: Small sparks may occur at the battery connectors during
reconnection. Take care not to short-circuit the positive and negative
battery terminals while replacing the battery.
8. Place the battery in the UPS.
9. Ensure correct alignment of front panel, then reattach the right-side cover.
Evenly tighten the four screws from Step 3. (Do NOT overtighten screws.)
Dispose of the old battery properly at an appropriate recycling facility.
TROUBLESHOOTING
If the UPS detects a fault, consult the table below for possible causes and solutions. For further assistance, please contact your local Emerson Network Power representative.
SPECIFICATIONS
!
CAUTION
Do not dispose of batteries in a fire. The batteries may explode.
!
CAUTION
Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It is toxic.
This product is designed for IT power systems with 230V.
Fault Possible Causes Solutions
Mains is normal, but LED 1 is not illuminated.
The UPS may not be turned on.
The power cord may not be connected properly.
The upstream mains circuit breaker may be tripped.
• Press the On/Off button to turn on the UPS.
• Connect the power cord securely into a wall socket.
• Reset the circuit breaker.
LED 1 flashes (green) every 3 seconds, but there is
no output power. Battery voltage may be too low. • Recharge the UPS for 8 hours.
Alarm buzzer beeps continuously although mains is
normal. The UPS may be overloaded (check LED 2). • Disconnect some equipment from the UPS.
UPS does not provide expected backup time. The UPS battery reached end of life. • Replace the internal battery.
The UPS is on and connected to mains, but fails to
operate properly. Mains power may be outside the unit’s operating range. • If mains is normal, try reconnecting mains and restarting the UPS.
Model Number PSP500MT3-230U PSP650MT3-230U
Capacity (VA/W) 500/300 650/390
Net Weight, kg (lb.) 3.9 (8.6)
Shipping Weight, kg (lb.) 4.8 (10.6)
Dimensions - W x D x H, mm (in.) 87 x 215 x 251 (3.4 x 8.5 x 9.9)
Mains Voltage 160-287VAC
Frequency 50/60Hz ±5Hz
Output Voltage (Mains Normal) Typical 160-287VAC
Output Voltage (Battery Operation) 230VAC ±5%
On-Battery Wave Form Stepped sinewave
VRLA Battery Type - VDC x Ah x Quantity 12V x 7.2Ah x 1 12V x 7.2Ah x 1
Typical Recharge Time 6-8 hours to 90%
Battery Run Time See Load Autonomy table at right Load Autonomy - Liebert PSP 230V 500VA-650VA
Audible and Visual Audible alarm / LED Load (watts) 500VA 650VA
Backup Sockets IEC 320 C13 (3) 50 55 56
Surge Sockets IEC 320 C13 (1) 100 18 19
Operating Temperature, °C (°F) 0 to 40 (32 to 104) 150 12 12
Storage Temperature, °C (°F) -15 to 40 (5 to 104) 200 8 8
Operating / Storage Relative Humidity 0%-90%, non-condensing 250 5 5
EMI Classification Class B 300 N/A 4
Agency 350 N/A 3
Safety IEC/EN/AS 62040-1-1 Note: All run times are in minutes, assume fully charged
batteries and are typical at 25°C (77°F) with resistive loads.
EMC
EN 62040-2:2005 Class B
IEC 61000-4-2 Electrostatic discharge
IEC 61000-4-3 Radiated E-RFI fields
IEC 61000-4-4 Fast E transients
IEC 61000-4-5 Surges/Lightning
IEC 61000-4-6 Conducted RFI
Transportation ISTA Procedure 1A Certification
Note: The Liebert PSP is compliant with the Restriction of Hazardous Substances Directive (ROHS),
prohibiting use of six hazardous materials manufacturing of electronics, including lead-free solder.
Step 1
Steps 2 and 3
ATTENTION:
Risk of
Electric Shock