Eminent EM8622 User manual

EM8622
Wireless Control Panel

2 | ENGLISH
EM8622 - Wireless Control Panel
Table of contents
1.0 Introduction ........................................................................................................... 3
1.1 Packing contents ............................................................................................... 3
1.2 Control panel front ............................................................................................. 3
1.3 Control panel inside ........................................................................................... 4
2.0 Installation ............................................................................................................. 4
3.0 Usage .................................................................................................................... 5
3.1 Arm the alarm system ........................................................................................ 5
3.2 Disarm the alarm system ................................................................................... 6
3.2.1 Using control panel to disarm ..................................................................... 6
3.2.2 Using RFID Tag to disarm .......................................................................... 7
3.2.3 Home Mode ................................................................................................ 7
3.2.4 Emergency Call .......................................................................................... 8
3.2.5 Mute Mode ................................................................................................. 8
4.0 Connect to the alarm system ................................................................................. 9
5.0 Connect RFID Tag to control panel ........................................................................ 9
6.0 Settings ............................................................................................................... 11
6.1 Enter Setup-state ............................................................................................. 11
6.2 Delay Arm........................................................................................................ 11
6.3 SOS Speed dial ............................................................................................... 12
6.3.1 Disable SOS code .....................................................................................13
6.3.2 Enable SOS code ......................................................................................13
6.4 Keyboard tone ................................................................................................. 14
6.4.1 Disable keyboard tone ...............................................................................14
6.4.2 Enable keyboard tone ................................................................................14
6.5 Disarm system by RFID tag ............................................................................. 15
6.5.1 Disable disarming by RFID tag ..................................................................15
6.5.2 Enable disarming by RFID tag ...................................................................15
6.5.3 Disarming silently by RFID tag ...................................................................16
6.6 Power saving mode ......................................................................................... 16
6.6.1 Enable power savig mode..........................................................................17
6.6.2 Disable power saving mode .......................................................................17
6.7 Change user code ........................................................................................... 18
6.8 Change admin code ........................................................................................ 18
6.9 Reset the control panel .................................................................................... 19
7.0 Frequently Asked Questions and other related information .................................. 19
8.0 Service and support ............................................................................................. 20
9.0 Warning and points of attention ........................................................................... 21
10.0 Warranty conditions ........................................................................................... 22
11.0 Declaration of Conformity .................................................................................. 23

3 | ENGLISH
1.0 Introduction
Congratulations with the purchase of this high-quality Eminent product! This product
has undergone extensive testing by Eminent’s technical experts. Should you
experience any problems with this product, you are covered by a five-year Eminent
warranty. Please keep this manual and the receipt in a safe place.
Register your product now on www.eminent-online.com and receive product updates!
1.1 Packing contents
The following parts need to be present in the packing:
 EM8622 Wireless Control Panel
 Manual
 3pcs AAA batteries
 External connection cable
 Screws and plugs
1.2 Control panel front
Led indicator
RFID tag reader
Arm button
Disarm button
Home mode button
SOS button
Wake-up button

4 | ENGLISH
1.3 Control panel inside
2.0 Installation
Install the batteries and mount the control panel on the door frame or the wall before
use.
Battery contact, please check
positive and negative
terminals
Battery compartment
Tamper switch
Wired cable connection
Red wire = + 12V
Black wire = - GND

5 | ENGLISH
1) Remove the screw and open the case
2) Install the batteries according to the positive and negative signs (Remove the
insulating strip before the first use)
3) Mount the backcover on the door frame or wall
4) Close the case and replace the screw
Note : Opening the cover will trigger the tamper switch ! You can disarm it by entering
the admin code 123456 followed by [#].
Note : The default admin code is : 123456. See chapter “Change Admin Code” to
change it.
Note : The default user code is : 1234. See chapter “Change User Code” to change it.
3.0 Usage
The control panel can be used as a remote control. User code or admin code should
be input before the operation of Arm, Disarm, Home Mode and Mute Mode.
3.1 Arm the alarm system
Input user code or admin code, and press [Arm] key. The LED indicator
flashes once and the control panel beeps once and sends Arm command to
the alarm system.
When the alarm panel receives the signal, the siren will beep once and the
Arm indicator will light on. The alarm system enters armed state.

6 | ENGLISH
If there is an intrusion the alarm system will be triggered, the siren will hoot
and the alarm system will send an SMS and auto dial to pre-stored phone
numbers to notify users.
Note : When an entry delay is set, the external control panel will NOT warn you with
an audio signal when a sensor is triggered. Only the alarm system itself will give an
audio signal !
3.2 Disarm the alarm system
Users can disarm the alarm system by using the control panel or by using RFID tags.
3.2.1 Using control panel to disarm
Input user code or admin code, and press the [Disarm] key. The LED indicator
flashes once and the control panel beeps once, and sends Disarm command to the
alarm system.
When the alarm panel receives the signal, the siren will beep twice and the Disarm
indicator will light. The alarm system enters disarmed state. In this state the sensors
being triggered will not cause an alarm.

7 | ENGLISH
3.2.2 Using RFID Tag to disarm
If direct disarm by RFID tag is disabled (this is the default power saving mode when
using batteries), user needs to press [*] to wake up the control panel and then put
RFID tag close to the reader to disarm the alarm system..
When the power saving function is disabled, user can put the RFID tag directly close to
the control panel to disarm the alarm system.
3.2.3 Home Mode
Input user code or admin code and press [Home Mode] key, the LED indicator flashes
once and the control panel beeps once and sends Home Mode command to the alarm
system.
When the alarm panel receives the signal, the siren will beep once and the Home
Mode indicator will light, the alarm system enters Home Mode state.
All the sensors in other zones are armed to prevent the intruder except that the motion
detector in Home Mode Zone is disarmed, so that people can move freely at home.
Note : Check manual of the alarm system for installing sensors in home mode.

8 | ENGLISH
3.2.4 Emergency Call
When the control panel is in SOS Speed Dial mode, user just holds the [SOS] key
for 3 seconds, the LED indicator flashes once, the control panel beeps once, and the
alarm system alarms immediately.
When the control panel is not in SOS Speed Dial mode, user needs to input user
code or admin code before holding the [SOS] key for 3 seconds to send an alarm.
3.2.5 Mute Mode
Mute mode means that the LED indicators of the control panel flash, but the siren
does not beep to avoid disturbing the neighbourhood.
Input user code or admin code, and hold any key of [Arm] [Disarm] [Home Mode] for
2 seconds. The LED indicator flashes once, the control panel beeps once and sends
corresponding command to the alarm system.
When the alarm panel receives the signal, the LED
indicator lights on or off, but the siren does not beep.

9 | ENGLISH
4.0 Connect to the alarm system
Note : The default admin code is : 123456. See chapter “Change Admin Code” to
change it.
Note : The default user code is : 1234. See chapter “Change User Code” to change it.
Make sure the alarm system is in connection state (press code on alarm system and
press the memo button).
Input the admin code on the control panel and press the Arm, Disarm or Home mode
button.
When the control panel is connected successful the alarm system will give one beep.
5.0 Connect RFID Tag to control panel
Note : The default admin code is : 123456
1. Input the admin code followed by the [#] button. ( a long beep is heard)
2. Immediatly after step one, press the 9 button. One beep is heard an the LED
indicator will be on for about 2 seconds. The control panel is in learning state.
During the time the LED is on, you can connect the RFID tag to the control panel.

10 | ENGLISH
3. Put the RFID tag close to the RFID reader. If one beep is heard the connecting is
successful. When 2 beeps are heard, the RFID tag was already connected to the
control panel.
To remove all connected RFID tags, input the admin code followed by the # button.
Press and hold down the 9 button for six seconds. All RFID tags are cleared after one
beep is heard.
Note : you can connect up to 50 RFID tags to the EM8622.

11 | ENGLISH
6.0 Settings
Before changing the settings of the control panel, the control panel should be in
“setup-state”.
6.1 Enter Setup-state
Note : The default admin code is : 123456
Input the admin code followed by the [#] button to wake up the control panel.
Press [3] to enter the setup-state. The LED indicator will be on.
Note : When there is no key press within 10 seconds the control panel will exit the
setup-state automatically. You can also press [#] to exit the setup-state.
6.2 Delay Arm
When the alarm system is armed, detectors will start working immediately. At that
time, if you are still at home, it will trigger the alarm system.

12 | ENGLISH
After setting a delay time, press the [Arm] button on the control panel. The control
panel will send the Arm command to the alarm system after the delay time you set in
the control panel.
Note : This setting will not apply to the Home mode. If both the control panel and the
alarm system have a delay time set, the actual delay time is the total of both times !
Enter the setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds the setup is
succesful.
Once the delay time is set, the control panel will beep once every two seconds when
the system is armed by the control panel. The reminding rhythm will speed up the last
15 seconds. After the delay time the alarm system enters arm state.
Note : Users can input a time between 0 – 250 seconds. Default setting is 0, no delay.
6.3 SOS Speed dial
If SOS code is disabled, you only need to press and hold the [SOS] key for 3 seconds
and the control panel will alarm immediately. If SOS code is enabled,you need to input
the code, press the [#] key,then press and hold the [SOS] key for 3 seconds.This
function is to prevent false operation or trick.

13 | ENGLISH
6.3.1 Disable SOS code
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
6.3.2 Enable SOS code
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
Note : Default setting is 0, SOS code is disabled.

14 | ENGLISH
6.4 Keyboard tone
Keyboard tones can be switched on or off.
If they are switched off, the beep when a setup is successful will also be switched off !
6.4.1 Disable keyboard tone
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
6.4.2 Enable keyboard tone
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
Note : Default setting is 1, keyboard tones are enabled.

15 | ENGLISH
6.5 Disarm system by RFID tag
Users can enable or disable the function of disarming the alarm system by RFID tag,
or disarming silent by RFID tag.
6.5.1 Disable disarming by RFID tag
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
6.5.2 Enable disarming by RFID tag
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.

16 | ENGLISH
6.5.3 Disarming silently by RFID tag
The alarm panel and siren will hoot twice when disarming the alarm system by RFID
tag. If set disarming silently by RFID tag, the alarm system and siren will keep silent
when disarming.
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
Note : Default setting is 1, turn on disarming by RFID tag and the siren will hoot when
disarming.
6.6 Power saving mode
If the control panel is powered by batteries, it is recommended to have the power
saving mode switched on.
In power saving mode, the control panel will go in to sleep mode when it is in stand-
by. Users need to press [*] to wake up the control panel and then put the RFID tag
close to the reader to disarm the alarm system.

17 | ENGLISH
6.6.1 Enable power savig mode
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
6.6.2 Disable power saving mode
If the control panel is powered by an external 12V power supply (not included), it is
recommended to switch of the power saving mode. Users can disarm the alarm
system directly by RFID tag.
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
Note : Default setting is 0, power saving mode switched on. User needs to press [*] to
wake up the control panel before using the RFID tag.

18 | ENGLISH
6.7 Change user code
A user can use its own code to wake up the control panel and send Arm, Disarm or
Home mode commands to the alarm system. The control panel can only have one
user code.
Note : The default user code is 1234. Please change this code at first use !
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
6.8 Change admin code
The admin code is used to wake up the control panel and send Arm, Disarm or Home
mode commands to the alarm system. With the admin code you can also change the
settings of the control panel.
Note : The default admin code is 123456. Please change this code at first use !
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.

19 | ENGLISH
6.9 Reset the control panel
After a reset the user code, admin code and all other settings will be restored to
default. Only the connected RFID tags will remain working. To remove the connected
RFID tags, please refer to chapter “Connect RFID Tag to control panel”.
Enter Setup-state and input :
When one beep is heard and the LED indicator keeps on for 10 seconds, the setup is
successful.
7.0 Frequently Asked Questions and other
related information
The latest Frequently asked questions for your product can be found on the support
page of your product. Eminent will update these pages frequently to assure you have
the most recent information. Visit www.eminent-online.com for more information about
your product.

20 | ENGLISH
8.0 Service and support
This user’s manual has been carefully written by Eminent’s technical experts. If you
have problems installing or using the product, please fill out the support form at the
website www.eminent-online.com/support.
You can also contact us by phone. Below you will find a list with phone numbers for
each supported country.
Country
Phone number
Rate per minute*
Belgium (Dutch) 070 277 286 €0.30
Belgium (French) 070 277 286 €0.30
Denmark [phone] Local Costs
Finland [phone] Local Costs
Germany [phone] Local Costs
Italy [phone] Local Costs
Norway [phone] Local Costs
Spain 807 080 042 €0.41
Sweden [phone] Local Costs
The Netherlands 0900-3646368 €0.10
UK [phone] Local Costs
Hungary 1-4088902 (From
Budapest)
Local Costs
Hungary 06-1-4088902 (From the
rest of Hungary)
Local Costs
Hungary [phone]
(International)
Local Costs
* Rates mentioned in this table do not include cell phone charges.