Emotion Fitness motion cardio line 900 User manual

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 1 from 17
Instructions for use
for
Pedal crank ergometer of the
motion cardio line 900 &
motion cardio line 900 med
motion cycle 900
motion cycle 900 med
motion relax 900
motion relax 900 med
motion body 900
motion body 900 med

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 2 from 17
Content
1. General.......................................................................................................................................................3
2. Classification of the devices.......................................................................................................................3
3. Safety instructions......................................................................................................................................4
Safe placement of the units .......................................................................................................................4
Safe training ...............................................................................................................................................6
Indications and contraindications..............................................................................................................8
4. Operating the display.................................................................................................................................9
Overview display/key functions.................................................................................................................9
Programme selection ...............................................................................................................................10
Pulse systems ...........................................................................................................................................10
Inductive charging (optional) ...................................................................................................................11
5. Care, maintenance and servicing.............................................................................................................12
Fault detection (malfunction) guide ........................................................................................................15
Maintenance instructions for the operator .............................................................................................15
Maintenance by authorised specialist .....................................................................................................15
Calibration/Maintenance.........................................................................................................................16
6. Technical data* ........................................................................................................................................16
7. Disposal ....................................................................................................................................................16
8. Warranty ..................................................................................................................................................17

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 3 from 17
1. General
Read this user manual with all safety instructions and warnings carefully before using the training
equipment for the first time to ensure safe and proper use. Keep this document for future
reference and give it to others if you pass on the equipment.
The purpose of the equipment is cardiopulmonary training and the reproducible loading of the
body, e.g. for diagnostic and therapeutic measures. The equipment is mainly used by users in cardiology,
physiotherapy, sports medicine and in the home. Another application is the use to build up and strengthen skeletal
muscles, as well as to increase mobility in the joints affected during training.
The equipment enables reproducible physical loading of the human body and the cardiovascular system for the
purposes of prevention, rehabilitation and diagnosis.
Text with a grey background indicates text sections that deal exclusively with equipment features of the fitness line.
2. Classification of the devices
The devices of the cardio line 900 med are medical products according to the directive 93/42 EWG, classified
in class IIa. In the control range of the brake, the display accuracy is +/- 5% or +/- 3 watts for loads below 50 watts.
The devices of the cardio line 900 comply with the standard DIN EN ISO 20957-1 and DIN EN ISO 20957-5;
application class S (commercial use/studio) and H (home use) of accuracy class A +/- 10 % and are designed
exclusively for the fitness and sports sector.
Only 1 person can exercise with the equipment at a time; the maximum user weight according to the type plate must not
be exceeded.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 4 from 17
3. Safety instructions
Safe placement of the units
motion cycle 900
motion cycle 900 med
Fig.1: Device view motion cycle 900 & motion cycle 900 med with designation of the essential elements and application parts
motion relax 900
motion relax 900 med
Fig.2: Device view motion relax 900 & motion relax 900 med with designation of the essential elements and application parts
Pedals
Adjustment screw for
horizontal saddle adjustment
Saddle
Display for showing training data
and for setting the unit
Handle
bar
Position name
plate
Adjustment lever for vertical
saddle adjustment
Adjustable feet for levelling
Display for showing training data and
for setting the unit
Position name
plate
Release lever for horizontal
saddle adjustment
Adjustable feet for levelling
Pedals
Adjustment lever for backrest
adjustment
Seat unit with
backrest and
handles
Handlebar

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 5 from 17
motion body 900
motion body 900 med
Fig.3: Device view motion body 900 & motion body 900 med with designation of the essential elements and application parts
motion body 900 WM
motion body 900 med WM
Fig.4: motion body 900 & motion body 900 med with designation of the essential elements and application
parts
ATTENTION: For the variant with wall mounting, the correct and secure fastening of the
wall brackets to the unit and the wall must be observed. First check the wall construction
and only if the wall is made of concrete or solid masonry can a secure fastening of the
unit be achieved with standard dowels. For each screw connection, at least
1000 N horizontal tensile load must be guaranteed so that the unit's strength is permanently maintained under all
conditions. The fastening must be carried out by a specialist company that also gives a guarantee on its work; the
procurement of the fastening material should also be carried out by the specialist company and adapted to the wall
condition. As an example, we recommend using Fischer long-shaft anchors SXRL 14x80 mm and matched FUS
screws 10 mm Ø.
Display for showing training data and
for setting the unit
Position name
plate
Adjustable feet for
levelling
removable seat
Height adjustment
release, "+/-" button
Handles &
adjustable crank
Height adjustment
release, "+/-" button
Display for showing training data and for
setting the unit
Position name
plate
Handles &
adjustable crank

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 6 from 17
Place the unit on a firm, horizontal, level and non-slip surface and level the unit with the
adjusting screws so that it does not wobble.
The clearance area around the unit must be at least 1 m larger than the movement
range of the unit to ensure safe access and egress from the unit even in emergencies.
However, the safety clearances may overlap (see picture).
Only place the appliance in dry rooms at , .
Make sure that there is no electromagnetic radiation, e.g. from radio antennas, radiating
fluorescent tubes, etc., as these can affect the pulse measurement.
The underside of the frame must always be free for sufficient ventilation.
All the pedal ergometers mentioned here are mains-independent. They generate the power themselves during
operation or are supplied with power during programming by the standard built-in capacitor. The capacitor is charged
by the training and has a service life of > 20000 cycles.
Attention: Please always follow the instructions for care, maintenance and servicing in chapter 5 of this manual.
Safe training
Before starting training, the fitness for training should be checked by an authorised person, e.g. a doctor. Please
note the point "Indications and contraindications".
Note that excessive exercise can be harmful.
If nausea or dizziness occurs, stop training immediately and consult a doctor.
Training on the equipment is only permitted with intact skin.
When training, tight-fitting, lightweight sports clothing is preferable so that it cannot get caught in parts of the device
during training. Always wear suitable sports shoes for a secure footing on the pedals.
Before starting the training, check the unit for safe standing, defective parts or possible manipulations. If you find
any defects or are not sure, ask the supervisor before starting the training.
Before starting training, make sure that nobody is near the moving parts in order to avoid endangering third parties.
In particular, unsupervised children must be kept away from the equipment.
cycle/relax: For biomechanically correct training, the knee should never be fully extended; adjust the seat of the
device accordingly.With the cycle 900 / 900 med, both the horizontal and the vertical sitting position can be changed.
For the vertical seat position, pull the locking bolt on the front of the seat post and adjust the height manually. For
an easier increase of the seat position, the seat post can be pulled upwards without unlocking the locking bolt. The
locking bolt automatically engages in the nearest lower hole. By pulling the locking bolt, the seat post can be adjusted
further down. Safety: Make sure that the locking bolt engages firmly and audibly before putting any load on the
saddle. The saddle position is indicated by a scale on the side of the seat post so that the personal saddle height
can be found more easily during repeated training. The saddle height should be chosen in such a way that there is
still a knee flexion of about 10° in the lowest pedal position.
Fig.5: Horizontal and vertical adjustment of the seat position on the cycle 900 & cycle 900 med
For horizontal positioning on the cycle, the yellow rubberised clamping handle behind the saddle must be loosened.
The saddle can then be moved forwards or backwards. The horizontal position of the saddle affects the inclination
of the upper body and the load that rests on the arms during the workout.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 7 from 17
Fig.6: Handlebar adjustment on cycle 900 & cycle 900 med
With the optionally available handlebar adjustment, care must be taken to ensure that the yellow rubberised
clamping handle is screwed tight again after adjustment and before training.
Fig.7: Horizontal and backrest adjustment of the seat position on the relax 900 & relax 900 med
For horizontal positioning on the relax, the yellow release lever must be pulled upwards. Then the seat unit can be
moved to the desired position. Make sure that the seat unit snaps firmly back into place. Adjust the backrest to the
desired position. Here, too, make sure that it engages in the correspondingly provided holes.
Fig.8: Vertical adjustment of the drive unit and the adjustable crank on the body 900 & body 900 med or body 900 WM and body 900 med WM
body: In order to be able to train biomechanically correctly with the body, move the drive unit so that the crank
holder on the machine is positioned at about shoulder joint height. Then adjust the crank length on the adjustable
cranks accordingly. The locking bolt of the adjustable crank must be re-engaged after adjustment and the
clamping lever must then be tightened.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 8 from 17
Warning: The heart rate monitoring system is susceptible to failure due to the system. Excessive exercise can
lead to dangerous injuries or death. If you feel unwell, stop exercising immediately and consult your doctor or
therapist.
Warning: The appliance may only be operated with a housing and in dry rooms.
Warning for optional power connection: Use only approved power supply units that have been tested
according to IEC 60601-1 and approved by the unit manufacturer. Make sure that the power supply is installed in
such a way that it is difficult to disconnect it (e.g. by means of floor tanks, installation under the unit or cable ducts,
position of the power supply in areas that are difficult to access).
Warning: If the medical device is modified, appropriate investigations and tests must be carried out to ensure
continued safe use. Do not modify the device without the permission of the manufacturer.
Indications and contraindications
Before starting training, please consult a doctor or therapist to ensure fitness for training.
Example indications
Mobility of the musculoskeletal system
Strengthening the musculature
Strengthening the cardiovascular system
Example contraindications
Cardiovascular diseases
Pain of the musculoskeletal system
During the training:
oChest pain
oMalaise
oNausea
oDizziness
oShortness of breath
Ask the doctor if you are taking medication.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 9 from 17
4. Operating the display
Various training and test programmes enable individual and varied training with the motion cardio line 900 and motion
cardio line 900 med machines.
body 900 / 900 med
relax 900 / 900 med
cycle 900 / 900 med
Basic equipment
Quickstart, timed training, pulse training
incl. programme package
Quickstart
Qualifying
Pulse training
+ 7 more programmes
Quickstart
Qualifying
Pulse training
+ 7 more programmes
+ 4 motion balance
programmes
Quickstart
Qualifying
Pulse training
+ 7 more programmes
+ 4 motion balance
programmes
+ 6 test programmes
Overview display/key functions
Fig. 9: Monitor view, explaining the button functions, actual view may vary in colour, button assignment is the same.
Explanation of the buttons:
The Home button is a physical button below the display glass. It is pressed to enter the main menu. Pressing
the HOME button for a long time (at least 6 seconds) resets the monitor electronics.
Press the PAUSE button ( ) to pause the training.
Pressing the PLAY button ( ) starts or resumes the training.
The COOL button ( ) stops the training immediately. A summary of the training results is immediately
generated, displayed and, if necessary, sent to a compatible training control software.
Use the "+" key or "-" key to increase or decrease the parameters or power values to be set.
Use the arrow keys to navigate through the corresponding menus and confirm values or settings.
Swipe/swipe gestures navigate through the programme selection.
Depending on the programme, some of the following parameters are displayed:
Programme name.
Time: Training time completed or remaining.
Pulse: Heart rate indicator, when using a compatible pulse transmitter belt. The pulse indicator display shows the
current pulse range for programmes with target or maximum pulse. The profile indicator in the display shows the
progression of the intensity range during training.
Watt: Power is displayed in watts. In parallel, the intensity is clarified via a graphic display in the profile.
km/h: Fictitious speed is displayed in km/h.
Speed: Pedal revolutions per minute.
L/R (not with body 900/900 med): The force ratio of the left and right leg is displayed here in %.
HRV: Heart rate variability is displayed via the RMSSD value (requires H10 sensor).
Home Button
PAUSE
COOL
PLAY

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 10 from 17
resp: Breathing rate (requires H10 sensor)
km: Added or remaining distance. The display is in metres; from 1000 m in 10 m steps (1.00 km).
K-Cal: Added or remaining calorie consumption.
Level: Intensity level 1 - 21.
: If the parameters are completed with this symbol, they are average values.
Results
After completion of a training programme or premature termination via COOL ( ), the results are displayed in the
monitor and a 3 minute cool-down takes place. This can be cancelled via the HOME button.
Some of the values are averaged (Watt, Km/h, RPM, Pulse, Altitude/ min), some are cumulated (Km, K-Cal, Time,
Altitude). The average values are marked with the symbol Ø.
These results make it possible to monitor personal performance development and thus serve as motivation.
Programme selection
The desired training programme can be selected in the main menu by tapping the corresponding symbol. You will then
be taken to the configuration page where you can set the corresponding training parameters. Press the PLAY button
() to confirm your entry and start the training. You can return to the main menu via the home icon or the home
button.
Fig. 10: Programme selection and configuration for manual training.
Pulse systems
The devices of the motion cardio line 900 and the motion cardio line 900 med have the original pulse system,
in which the signal acquisition takes place by means of a chest strap as standard. This enables individual training in
various programmes. The wireless data transmission to the display electronics is coded (either via 5kHz or ).
The new "Auto-Pairing" technology is based on secure and interference-free data transmission via Bluetooth.
This technology requires the use of the H10 or H9 transmitters. Other parameters, such as HRV and respiratory rate,
are also transmitted to the monitor via the connection.
If the old transmitters are used, e.g. T31coded, there is downward compatibility. It should be noted, however, that there
may be interference with the signal transmission via the 5 kHz technology.
The colour of the flashing heart symbol gives an indication of the technology used.
light blue=Bluetooth green=5kHz
ANT+
The devices of the motion cardio line 900 and motion cardio line 900 med allow, in addition to the transmission of the
heart rate via 5kHz/ , an optional data transmission via . The performance package is required for this.
By default, Polar 5kHz/ technology is activated. To activate transmission via , the "ANT+" switch in the
info box ( ) must be switched on (marked yellow here). After that, a connection to a transmitter unit that sends the
heart rate via can be established. A dark blue flashing heart symbol confirms the heart rate transmission via .

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 11 from 17
Fig. 11: Activation of ANT+ for heart rate transmission
Inductive charging (optional)
An optional inductive charging module can be activated on all motion cardio line 900 and motion cardio line 900 med
units via the "connect package". This allows mobile devices that comply with the Qi standard ( ) to be charged
without contact. Wearers of pacemakers or implanted defibrillators (ICDs) are recommended to keep a minimum
distance of 10 cm from the charging coil.
Safety instruction according to DIN EN ISO 20957
Warning. Heart rate monitoring systems can be inaccurate. Excessive
exercise can cause serious damage to health or death. Stop exercising
immediately if you feel dizzy or weak.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 12 from 17
5. Care, maintenance and servicing
All cardio equipment from emotion fitness is durable and requires little maintenance to function as training equipment
for a long time. However, it is imperative that the necessary care is carried out conscientiously.
Warning: The unit may only be opened by an authorised specialist
Symbols and meaning
Safety sign
Reference
Title
ISO 7010-P017
Pushing prohibited
ISO 7010-W012
Warning, electricity
ISO 7000-1641
Instructions for use
DIN EN ISO 20957
Safety Notice Heart Rate
Monitoring
ISO 7000-3082
Manufacturer
ISO 7000-2497
Date of manufacture
ISO 7000-0632
Temperature limit
ISO 7000-2620
Air humidity, limitation
ISO 7010-W001
General warning sign

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 13 from 17
ISO 7010-M002
Follow the operating
instructions
IEC 60417-5840
Type B applied part
(concerns saddle, pedals
and handlebars)
ISO 15233
Medical device
The safety level of the units can only be maintained if the units are regularly checked for damage and wear. Defective
parts must be replaced immediately and the unit must be shut down until it is repaired.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 14 from 17
Fault diagnosis
The following error messages may occur. If the error is displayed repeatedly, the measures listed below can help. If
these do not lead to success, themanufacturer/dealer and, if necessary, the software manufacturer should be contacted.
Error message
Measure/s
Affected
unit types
"RFID Error"
RFID number, i.e. number on transponder is too
short or too long.
An error occurred while reading the RFID number.
use a different transponder
All
ergometers
"Heart Sensor?"
The monitor wants to start a programme that
requires a heart rate sensor to be worn. If no sensor
is found, this message is displayed.
All
ergometers
"USB Problem"
The radio message was successfully sent from the
radio module of the monitor to the radio module of the
PC (i.e. the receiver module acknowledged receipt of
the message), but there was no response from the
PC after the specified time period:
Restart the PC and plug the USB dongle into the
PC again. If necessary, restart the software service.
All
ergometers
"Radio Problem"
The unit does not receive a response from the USB
dongle.
Attention! This error message can also be displayed
if the message sent from the dongle to the monitor is
faulty (e.g. wrong format or message incomplete).
Restart the PC and plug the USB dongle into the
PC again. If necessary, restart the software service.
All
ergometers
"NDEF err: length"
The message found on the NFC tag (i.e. the
message transmitted from the smartphone) is too
long.
Contact the software manufacturer or device
manufacturer
All
ergometers
"NDEF err: verify"
The NFC tag could not be accessed. This is an
authorisation problem when accessing the NFC tag
through the monitor using the super password.
Contact the manufacturer or software producer
All
ergometers
Missing value: XX
(XX=number)
A necessary setting parameter was not sent to the
ergometer by the PC softwareContact the
manufacturer or software producer.
All
ergometers
Value XX out of Range
(XX=number)
A necessary setting parameter was sent outside the
permissible range from the PC software to the unit
contact the manufacturer or software producer
All
ergometers

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 15 from 17
Fault detection (malfunction) guide
If any faults occur on the equipment that you cannot classify, please contact emotion fitness GmbH & Co.KG. For each
error message, you should have the serial number and model type of the defective device ready, as this could be
important in order to be able to make the correct diagnosis and, above all, to provide the appropriate replacement parts
for you!
Maintenance instructions for the operator
Ideally, visually inspect the unit before each use, but at least daily, and pay particular attention to defective parts, loose
connections and atypical noises.
The following checks must be carried out at least every 6 months:
Visually inspect all visible joints, as well as welds.
Clean the unit thoroughly.
Check all screw connections for tightness.
Check the integrity of the saddle and seat post and ensure that the saddle is replaced after 2 years to
prevent material fatigue.
Check the integrity and strength of the pedals and cranks.
Generally speaking:
Clean the plastic casing and frame parts regularly as required with a damp cloth and mild soap, then wipe
dry again.
The use of spray bottles with cleaning agents is not permitted; it has been shown that the units never
become dry in inaccessible places. Rust infestation cannot be ruled out by this procedure.
Make sure that no liquid gets into the monitor housing,
For any necessary disinfection of the devices, please use only mikrozid® sensitive wipes disinfectant
wipes (http://www.schuelke.com/).
The monitor display may show a capacitor voltage that is too low, at which a function without braking
current cannot be safely guaranteed. You can recharge the capacitor by pedalling with a higher load or a
power supply unit approved by the device manufacturer.
Check the housing fixings for tightness.
Check the detent pins regularly for function.
We recommend a regular visual inspection of all parts of the unit, especially screws, bolts, welds and other
fixings.
Check that the feet of the appliance are firmly seated.
Check whether the cranks are still firmly connected to the axle. You will need a 14 mm socket spanner for
this.
Important: Retighten after the first 10 hours of use! Damaged cranks and axles due to loosening of the
cranks are not covered by the warranty!
Check the seat post for damage due to overloading.
Clean the seat post and seat slide extension parts, then spray with silicone spray and rub dry again.
Check the pedal loops for damage.
Only use original spare parts - contact us for this.
Attention: Retighten the cranks
After the first 10 hours of operation, the cranks must be tightened.
If the cranks are not tightened, irreparable damage to the axle or cranks may occur, in which case there is no longer any
warranty.
Maintenance by authorised specialist
In the event of problems with the device that you cannot solve yourself in a simple manner, always contact the emotion
fitness service department. The authorised service will help you quickly and competently or provide you with instructions.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 16 from 17
Calibration/Maintenance
All medical pedal ergometers are subject to a MTK obligation (MPBetreibV, §14) and must be checked every 24
months.
In addition, we recommend maintenance with inspection of the safety-relevant components (STÜ) by authorised
employees/partners every 12 months.
This section refers to the legal situation in Germany. Please check the applicable laws for operating medical devices in
your country.
Devices with the suffix "med" are in accordance with the Medical Devices Directive 93/42/EEC. They thus bear the CE
mark and the number of the notified body.
The distributor/operator is responsible for carrying out maintenance, servicing and calibration, as well as possible
inspections in accordance with applicable regional laws and regulations at the location of the units!
Your local authorised dealer can also provide further information.
6. Technical data*
Device type
Dimensions (L/W/H)
Weight
Max. user weight
Safe workload
motion cycle 900
motion cycle 900 med
119 cm x 65 cm x
145 cm
58 kg
150 kg; boosted:
200 kg
208 kg; boosted:258 kg
motion relax 900
motion relax 900 med
motion relax 900 boosted 250kg
motion relax 900 med boosted
250kg
173 cm x 65 cm x
133 cm
173 cm x 78 cm x
133 cm
80 kg
104 kg
150 kg; boosted:
200 kg;
boosted:250 kg
230 kg; boosted: 280 kg;
boosted: 354 kg
motion body 900
motion body 900 med
motion body 900 WM
motion body 900 med WM
116 cm x 78 cm x
155 cm
63 cm x 56 cm x
155 cm
98 kg
48 kg
150 kg; boosted:
200 kg
150 kg; boosted:
200 kg
248 kg; boosted: 298 kg
198 kg; boosted: 248 kg
Resistance system: Mains-independent braking system
Performance area:
cycle/relax: speed-independent: 15-500 watts (optionally 7-950 watts); speed-dependent: 15-1,000 watts
body: speed-independent: 15-500 watts (optionally 7-550 watts); speed-dependent: 15- 750 watts
Freewheel: available for cycle and relax
The following EU directives are fulfilled:
2001/95/EC General Product Safety Directive
93/42/EEC Medical Devices Directive Class IIa (only fulfilled for devices with the suffix med)
2014/30EU EMC Directive
The following standards were used:
DIN EN ISO 20957-1 Accuracy class A, use class SH; DIN EN ISO 20957-5;
DIN EN 60601-1:2013; DIN EN 60601-1-2
* Values may vary due to unit changes and options.
We reserve the right to make technical and optical changes as well as printing errors.
7. Disposal
With the conclusion of the purchase contract, it shall be deemed agreed that business customers will dispose of the
EU Directive 2002/96/EU on waste electrical and electronic equipment themselves.

Instruction manual Pedal ergometer 900 / 900 med Version 1.3 25.01.2023
Page 17 from 17
8. Warranty
This is based on the statutory warranty.
emotion fitness GmbH & Co KG as the manufacturer of this product will provide free replacement for defective parts
for 24 months from the date of invoice by emotion fitness for professional users if the proper use and care listed in this
user manual can be proven.
As a rule, the cost of labour for a warranty service during the first 12 months is paid by the respective dealer in your
country. Please contact your respective dealer if you have any questions about this.
The warranty will be void if the product has been serviced or repaired by unauthorised persons. As soon as a warranty
claim occurs, you should immediately inform emotion fitness GmbH & Co KG or your dealer in writing or by e-mail.
Information about the serial number of the equipment, the date of purchase, a detailed description of the fault and the
source of supply must be provided by the owner of the equipment.
emotion fitness GmbH & Co. KG or your distributor will arrange for service, but reserves the right to determine the type
of service.
The following procedures are possible:
1. the service will be carried out on site by an authorised service technician.
2. we send the requested spare part.
3. we send a replacement unit.
The defective parts are returned to us immediately by the customer at no charge. Otherwise the customer will be
charged
of the delivered spare parts.
If the causes lie outside the warranty area, emotion fitness GmbH & Co KG reserves the right to charge all repair
costs.
Some wearing parts are not covered by the warranty. These are in particular the saddle, cranks and crank attachment,
pedals, pedal loops, upholstery fabrics and the rubber grip on the handlebars. The pulse systems come with
the legal warranty.
These warranty provisions shall in no way affect the general statutory claims.
Our General Terms and Conditions of Export, as amended from time to time, can be viewed and downloaded from our
website at
www.emotion-fitness.de and can be downloaded.
Thank you for your trust!
Manufacturer
emotion fitness GmbH & Co. KG
Trippstadter Str. 68
67691 Hochspeyer, Germany
Tel [phone]
Fax [phone]
Internet: www.emotion-fitness.de
E-mail: [email protected]
Manufacturer EUDAMED SRN: DE-MF-000016584