Empire DVCT30 User manual

42035-0-0420 Page 1Empire Comfort Systems Inc. • Belleville, IL
INSTALLATION
1. Turn off gas and electric to unit. Take unit out of the
replace if applicable.
2. Remove 4 screws and remove outer top, repeat for other
side. Set parts aside, they will be re-used. See Figure 1.
Figure 1
3. Remove 6 screws to blower assembly and disconnect
wire harness to blower. Discard blower assembly, it will
not be needed. See Figure 2.
Figure 2
4. Remove 7 screws and remove outer rear assembly.
Discard this assembly, it will not be needed. See
Figure 3.
Figure 3
5. Remove 3 screws and remove outer left side. Discard
this part, it will not be needed. See Figure 4.
Figure 4
FOR USE ON: DVCT30 AND DVCT35 DASH-1 UNITS
INSTALLATION INSTRUCTIONS
BLOWER & LIGHT REPLACEMENT KIT

42035-0-0420Page 2 Empire Comfort Systems Inc. • Belleville, IL
6. Remove 2 bolts holding the slide plate into place if
you have not already done so. Set aside, it will be re-
used. Also remove wire shield with 1 screw, replace
screw and discard shield. Shield will not be needed.
See Figure 5.
Figure 5
7. If liner is installed, you will need to remove the top
bracket held in by 3 screws. Remove top liner and set
these items aside, they will be re-used. See Figure 6.
Figure 6
8. Remove 5 screws holding right shield and pull right
shield aside, be careful since it has several wire
harnesses still attached to unit. See Figure 7.
Figure 7
9. Remove 2 wires shown in Figure 8.
Figure 8
LIGHT WIRES
POWER WIRES NOT SHOWN
LIGHT WIRES
POWER WIRES NOT SHOWN
—
LIGHT
WIRES

42035-0-0420 Page 3Empire Comfort Systems Inc. • Belleville, IL
10. Remove 4 screws, bezel, gasket, and glass from
light assembly. Remove 4 screws holding the light
assembly to the rebox top and carefully remove it
from the unit. Discard all of these items, they will not
be needed. See Figure 9.
Figure 9
11. Re-install the new light assembly in reverse order of
step 10. Use Figure 9 as reference. Route wires to
control module and attach. See Figure 8.
12. Re-attach right side panel in step 8 with 5 screws.
13. Re-attach slide plate with 2 bolts, you may choose to do
this step at a later time. This will depend on your install.
See Figure 10.
Figure 10
14.
Install new left side assembly using 3 screws. See
Figure 11.
Figure 11
15. Line up the 2 screws coming out of the rear of the
rebox with heat shield assembly, using 2 self drilling
screws, secure heat shield as shown in Figure 12.
Figure 12

42035-0-0420Page 4
16. Install new rear assembly using 7 screws. See Figure 13.
Figure 13
17. Re-attach outer tops to unit, be careful with light
assembly wire harness, do not pinch wires under top,
wires should run between top and center combustion
box. See Figure 14.
Figure 14
18. Re-attach blower wire harness to blower. Attach new
blower assembly to unit using 6 screws, be careful not
to pinch wires between metal. See Figure 15.
Figure 15
19. If liner was installed before this process, you will need
to replace the liner top in reverse order of step 7.
20. Return unit into place and you may now turn gas and
electric back on. It is recommended to check for leaks at
this time. The rework has been completed at this time.
www.empirecomfort.com
Empire Comfort Systems Inc.
Belleville, IL
If you have a general question
about our products, please e-mail
us at [email protected].
If you have a service or repair
question, please contact your dealer.