Emulex LP8000 Installation and operating manual

LP8000 Installation and Reference Manual
Table of Contents
Installation
Compatability
Prerequisites
Set Jumpers
Install HBA
Change GBIC
Attach Media
Apply Power
View LEDs
Reference
Specifications
DB9 Pinout
FCC and Regulatory Notices
Declaration of
Conformity
Laser Safety
Emulex Drivers, Software and Manuals
1

Chapter 1 − Installation
Table of Contents
Compatability
Prerequisites
Set Jumpers
Install HBA
Change GBIC
Attach Media
Apply Power
View LEDs
Emulex Drivers, Software and Manuals
2

Installation
Caution Emulex LightPulse Host Bus Adapters (HBAs) contain
electronic components that can be damaged by static
electricity through an electrostatic discharge (ESD) event. To
prevent ESD damage, maintain frequent contact with any
grounded metal surface. A grounding wrist strap is useful for
this purpose. Handle the card carefully at all times and
preferably by the edges. Avoid touching electronic
components and keep the card in the original packaging until
you are ready for installation.
Compatibility
Software
Environments Windows Server 2003, Windows 2000, Windows NT, NetWare, HP-UX, Linux, Solaris, AIX
Hardware
Environments PCI hardware platforms: x86, SPARC and PowerPC
Prerequisites
One open 32−bit or 64−bit (recommended) PCI bus slot with a 3.3 VDC
or 5.0 VDC signaling interface
•
Maximum PCI bus clock rate of 33 MHz• Media and connectors (user supplied)• Multimode fiber optic cable (50/125 µ m or 62.5/125 µ m) with
dual SC connectors, used with short wave lasers
♦
Single mode fiber optic cable (9/125 µ m) with dual SC
connectors, used with long wave lasers
♦
Copper duplex cabling with DB9 connectors (also called DE9)♦
Emulex Drivers, Software and Manuals
3

Set Jumpers
The host adapter has two jumper blocks (JX1, JX2) that control the host adapter's
device ID. The default Device ID is F800.
Device ID Jumper Setting
F800 JX1:1−2, JX2:2−3
F801 JX1:2−3, JX2:1−2
1AE5 JX1:2−3, JX2:2−3
Emulex Drivers, Software and Manuals
4

Install Host Bus Adapter Board
Record IEEE address and serial number.
Each host adapter is shipped with a unique address identifier called the
IEEE address. The Fibre Channel industry uses a World Wide Name
(WWN) derived from the IEEE address, and this number is need for
arbitrated loop connectivity. The serial number is used when
communicating with Emulex. Both numbers are clearly marked on the
board. We recommend that you record these numbers before installation.
1.
Turn off and unplug the computer.2. Remove the computer case.3. Remove the blank panel from an empty 32− or 64−bit PCI bus slot.4. Insert host adapter board into the empty 32− or 64−bit PCI bus slot.
Press firmly until the board is seated.
5.
Secure the host adapter's mounting bracket to the case with the panel
screw.
6.
Replace the computer case and tighten case screws.7.
The host adapter is now installed in the PC and is ready for media attachment.
Emulex Drivers, Software and Manuals
5

Change the GBIC Connector
A GBIC, or Gigabit Interface Converter, is a connector that offers a flexible
choice of copper or fiber optic media. A GBIC supports either short wave or long
wave optical transmission. These types are available:
Short−wave fiber optic GBIC with dual SC connectors• Long−wave fiber optic GBIC with dual SC connectors• Copper GBIC with DB9 connector•
Caution An Emulex supplied GBIC is required to maintain regulatory
compliance with worldwide certifications (for example, FCC,
C−Tick, CE, and so on).
A GBIC should be matched with its cabling to obtain optimum performance and
distance. For example, a short wave fiber optic GBIC best supports either
62.5/125 or 50/125 multimode cable, while a long wave fiber optic GBIC
functions best with 9/125 single mode cable.
To change a GBIC:
Exert slight pressure on the tabs.1. Gently pull out the GBIC as shown.2. Slide in a new GBIC, pressing firmly to seat the GBIC into the board.3.
Emulex Drivers, Software and Manuals
6

Attach Media
Attach fibre optic or copper cable to the host bus adapter.
Attach Fiber Optic Cable (Multi/Single Mode)
Note The host adapter will not allow normal data transmission on
an optical link unless it is connected to another similar or
compatible laser product (that is, multimode to multimode.)
Use fiber optic cable supporting a data rate of 1.0625 Gb/s for short−wave and
long−wave lasers, that adheres to the following specifications:
Fiber Optic Cable Maximum
Length Minimum Length Connector
62.5/125 µm
(multimode) 175 meters 2 meters Dual SC
50/125 µm (multimode) 500 meters 2 meters Dual SC
9/125 µm (single mode) 10,000 meters 2 meters Dual SC
Connect the fiber optic cable to the dual SC connector on the host
adapter board as shown.
1.
Connect the other end of the cable to the Fibre Channel device.2.
After the media is connected to the host adapter, you are ready to apply power to
the computer.
Emulex Drivers, Software and Manuals
7

Attach Copper Duuplex Cable
Use copper Twinax or Quad Axial cable that adheres to the following
secifications:
Cable Type Maximum Length Data Rate Connector
Twinax or Quad Axial 30 meters 1.0625 Gb/s DB9
Connect the copper duplex cable to the DB9 connector on the host
adapter board as shown.
1.
Connect the other end of the cable to the Fibre Channel device.2.
After the media is connected to the host adapter, you are ready to apply power to
the computer.
Emulex Drivers, Software and Manuals
8

Apply Power
Verify that the host adapter is securely installed in the computer.1. Verify that correct media is attached.2. Plug in and turn on the computer.3. Observe LEDs for Power On Self Test (POST) results.4.
View LEDs
Green and yellow display lights (LEDs) can be seen through openings in the host
adapter's mounting bracket. Green indicates power and yellow signifies port
activity. A third LED is present on LP8000 models with embedded optical
interfaces, and indicates that light is being received by the port.
POST conditions and results are summarized in this table.
Green
LED Yellow LED State
OFF OFF Wake−up failure (dead board)
OFF ON POST failure (dead board)
OFF Slow blink (1 Hz) Wake−up failure (dead board)
OFF Fast blink (4 Hz) Failure in POST (dead board)
OFF Flashing (irregular) POST processing in progress
ON OFF Failure while functioning
ON ON Failure while functioning
ON Slow blink (1 Hz) Normal − link up
ON Fast blink (4 Hz) Normal − Updating firmware or driver initializing
Blink OFF Normal − link down or not yet started
Emulex Drivers, Software and Manuals
9

Chapter 2 − Reference
Table of Contents
Specifications
DB9 Pinout
FCC and Regulatory Notices
Declaration of Conformity
Laser Safety
Emulex Drivers, Software and Manuals
11

Hardware Reference
Specifications
Parameter Range
Hardware Interface 20 pin connector for GBIC models
Physical Dimensions Short PCI form factor 6.88" x 4.20"
Power Requirements 11 watts @ + 5.0 VDC (typical)
Airflow 100 lfm minimum
Temperature Operating:K2° to 113° F (0° to 45° C)
Storage:I4° to 131° F (−10° to 55° C)
Humidity 5% to 95% non−condensing
Agency Approvals for
LP8000−D1 UL recognized to UL1950
CUR recognized to CSA22.2, No. 950
TUV certified to EN60950
FCC Rules, Part 15, Class A
Industry Canada, ICES−003, Class A
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class A
EN50082−1
Australian EMC Framework (C−Tick Mark)
AS/NZS 3548: Class A
VCCI, Class A.
Agency Approvals for
LP8000−N1/T1/L1
and LP8000−F1
Class 1 Laser Product per DHHS 21CFR (J) & EN60825
UL recognized to UL1950
CUR recognized to CSA22.2, No.950
TUV certified to EN60950
FCC Rules, Part 15, Class B
Industry Canada, ICES−003, Class B
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class B
EN50082−1
Australian EMC Framework (C−Tick Mark)
AS/NZS 3548: Class B
VCCI, Class B
Emulex Drivers, Software and Manuals
12

Hardware Reference
Copper Port (DB9) Pinout
This pinout applies to embedded copper ports.
Pin Signal Direction
1 TX+ Output
2 VCC VCC
3 Fault - Input
4 Key NC
5 RX+ Input
6 TX- Output
7 ODIS + Output
8 GND GND
9 RX- Input

Hardware Reference
FCC and Regulatory Notices
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A` LASER DE CLASSE 1
TO IEC 825−1 (1993) + CENELEC HD 482 S1
The above statement applies to products marketed in the European Union.
Model LP8000−D1 (Embedded Copper)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense. Shielded cables must be used between this
equipment and attached peripheral devices. The reader is cautioned that changes
or modifications made to the equipment not expressly approved by Emulex could
void the user's authority to operate this equipment.
The above statement applies to products marketed in the USA
This class A digital apparatus meets all requirements of the Canadian
Interference − Causing Equipment Regulations.
Cet appareil numerique de la Classe A respecte toutes les exigences du reglement
sur le materiel brouilleur du Canada.
This statement applies to products marketed in Canada.
FCC Compliance Information Statement; Models LP8000−N1/L1/T1 (GBIC
Models):
Emulex Drivers, Software and Manuals
13

FCC Compliance Information Statement; Model LP8000−F1 (1 X 9):
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party: Paul Folino, President & CEO, Emulex Corporation, 3535
Harbor Blvd., Costa Mesa, CA 92626, USA, (714) 662−5600
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.•
Emulex Drivers, Software and Manuals
14

The reader is cautioned that any changes or modifications to the equipment not
expressly approved by Emulex could void the user’s authority to operate this
equipment.
This class B digital apparatus meets all requirements of the Canadian
Interference − Causing Equipment Regulations. Cet Appareil numerique de la
classe B respecte toutes les exigences du reglement sur le material brouilleur du
Canada.
The above statement applies to products marketed in Canada.
VCCI Notices and Translations (Japan Only)
Note VCCI regulations provide that changes or
modifications not expressly approved by Emulex
Corporation could void your authority to operate this
equipment.
LP8000−N1/ L1/T1/F1 (GBIC and 1x9 Models):
Translation:
This is a Class B product based on the standard of the Voluntary Control Council
for Interference by Information Technology Equipment (VCCI). If this
equipment is used near a radio or television receiver in a domestic environment,
it may cause radio interference. Install and use the equipment according to the
instruction manual.
LP8000−D1 (Embedded Copper Model):
Translation:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures. VCCI—A
Emulex Drivers, Software and Manuals
15

Manual Notice
Translation:
This is a Class A product based on the standard of the Voluntary Control Council
for Interference by Information Technology Equipment (VCCI). If this
equipment is used in a domestic environment, radio disturbance may arise. When
such trouble occurs, the user may be required to take corrective actions.
Emulex Drivers, Software and Manuals
16

Hardware Reference
Declaration of Conformity
Note Changes or modifications not expressly approved by Emulex
Corporation could void the user's authority to operate this
equipment.
DECLARATION OF CONFORMITY
Manufacturer: Emulex Corporation
3535 Harbor Blvd.
Costa Mesa, CA 92626
USA
declares under sole responsibility that the product:
Product
Name: LightPulse™ LP8000 Fibre Channel PCI Host Adapter
Assembly
Number: FC1020017−XX (GBIC model) FC1020016−XX (embedded optical, 1x9 model)
Accessories: Emulex PN 2300029 (Active Copper DB9 GBIC Module)
Emulex PN 2300028 (Shortwave Optical GBIC Module)
Emulex PN 2300030 (Longwave Optical GBIC Module)
to which this declaration relates is in conformity with the following
standards or other documents:
Safety: IEC950:1991+A1,A2/EN60950 (1992)+ A1,A2
including EN60825−1 (1994)
TUV Rheinland, Certificate No. R9677151.1
EMC: EN55022 (1994)/CISPR−22 (1993), Class A
EN50082−1 (1997)
following the provisions of the Low
Voltage Directive 73/23/EEC and EMC
Directive 89/336/EEC (as amended by 92/31/EEC) and is Marked in
accordance with the CE Marking Directive 93/68/EEC
February 18, 1999
Costa Mesa, CA
European Contact: Emulex Corporation
7 & 8 Forrest Court
Oaklands Park
Fishponds Road
Wokingham, Berkshire
RG41 2FD, England
Telephone:
44−118−977−2929
Fax: 44−118−977−3237
Emulex Drivers, Software and Manuals
17

This equipment complies with CISPR22/EN55022 Class A.
Warning This is a class A product. In a domestic environment, this
product may cause radio interference requiring the user to
take adequate measures.
This Declaration identifies the product, manufacturer's name and address, and
applicable specifications recognized in the European Union.
DECLARATION OF CONFORMITY
Manufacturer: Emulex Corporation
3535 Harbor Blvd.
Costa Mesa, CA 92626
USA
declares under sole responsibility that the product:
Product
Name: LightPulse™ LP8000 Fibre Channel PCI Host Adapter
Assembly
Number: FC1020019−XX (Embedded DB9 model)
to which this declaration relates is in conformity with the following
standards or other documents:
Safety: IEC950:1991+A1,A2/EN60950 (1992)+ A1,A2
TUV Rheinland, Certificate No. R9677151.1
EMC: EN55022 (1994)/CISPR−22 (1993), Class A
EN50082−1 (1997)
following the provisions of the Low
Voltage Directive 73/23/EEC and EMC
Directive 89/336/EEC (as amended by 92/31/EEC) and is Marked in
accordance with the CE Marking Directive 93/68/EEC
November 25, 1998
Costa Mesa, CA
European Contact: Emulex Corporation
7 & 8 Forrest Court
Oaklands Park
Fishponds Road
Wokingham, Berkshire
RG41 2FD, England
Telephone:
44−118−977−2929
Fax: 44−118−977−3237
FC1055001−07B
February 2000
Emulex Drivers, Software and Manuals
18

Laser Safety Notice
This laser safety information contains certification and product information
covering laser products known as optical Gigabaud Link Modules (GLMs),
Gigabit Interface Converters (GBICs), 1x9 and small form factor transceivers
sold as accessories to or incorporated in Emulex LightPulse host adapters. The
GLM, GBIC, 1x9 and small form factor transceiver are the primary cable
connection mechanisms for any optical port on the host adapter and hub. This
data is not intended to be a replacement for any safety regulations and standards;
relevant safety documents should always be consulted if necessary. Contact
Emulex Corporation with any questions or concerns about laser safety.
Certification and Classification
Labeling Requirements
Product Information
Usage Restrictions
System Level Certification
Certification and Classification
LP6000 and LP7000E PCI host adapters may contain a laser product known as
an optical Gigabaud Link Module (GLM). The optical GLM is attached to the
host adapter using an 80−pin connector and extends through the mounting
bracket. In turn, the host adapter can be inserted into any host system's PCI slot.
The LH5000 hub may contain a laser product known as a Gigabit Interface
Connector (GBIC). The GBIC provides the physical connector to the optical
cable. The GBIC can be inserted into any pluggable hub port.
The LP8000, LP850 and LP9000 PCI host adapter may contain a laser product
known as a Gigabit Interface Converter (GBIC) or an embedded 1x9 transceiver.
The GBIC and or 1x9 transceiver provide the physical connection to the optical
cable, and its SC−style connector extends through the mounting bracket. In turn,
the host adapter can be inserted into any host system’s PCI slot.
The LP9002, LP9002L, LP952L, LP9002S, LP9002DC, LP9002C, and
LP9402DC PCI host adapters may contain a laser product known as a small form
factor transceiver. This transceiver provides the physical connection to the
optical cable, and its LC−style connector extends through the mounting bracket.
In turn, the host adapter can be inserted into any host system's PCI/cPCI slot.
In the United States, all optical GLMs, GBICs, 1x9 and small form factor
transceivers sold by Emulex are certified as Class 1 laser products that conform
to the requirements contained in the Department of Health and Human Services
(DHHS) regulation 21 CFR subchapter J. The certification is indicated by a label
located on the optical GLM, GBIC, 1x9 or small form factor transceiver.
Emulex Drivers, Software and Manuals
20

In Europe, all optical GLMs, GBICs, 1x9 and small form factor transceivers sold
by Emulex are certified as Class 1 laser component assemblies that conform to
the requirements contained in the CENELEC (European Committee for
Electrotechnical Standardization) standard EN60825−1:1994 (including
amendment 11) and EN60825−2:1994. GLMs, GBICs, 1x9 and small form factor
transceivers are certified by a recognized European testing agency and have
appropriate markings on the assembly. The DHHS conformity label and
European conformity mark will not be visible externally once the optical GLM,
GBIC, 1x9 or small form factor transceiver is connected to or inserted in the host
adapter and the adapter is installed into a system.
Labeling Requirements
No caution or danger labels are required for use of the GLM, GBIC, 1x9 or small
form factor transceiver since they are Class 1 laser component assembly. In the
U.S., the only laser safety label required is the DHHS certification label that
already appears on the GLM, GBIC, 1x9 and small form factor transceiver. In
Europe, the EN60825−1/EN60825−2 standards require that the system−level
product has a Class 1 information label permanently attached and clearly visible
whenever access to the GLM, GBIC, 1x9 and small form factor transceiver
optical port is possible. Each Class 1 product shall have affixed an explanatory
label bearing the words:
Alternatively, at the discretion of the manufacturer, the same statement may be
included in user information. If a label is used, an example of the IEC Class 1
information label that is suitable for most European countries is shown below.
The label consists of black printing on a white background. Languages
represented on this label are English, German, Finnish and French, and they
represent the minimum set for acceptance of a Class 1 product in most European
countries.
Emulex Drivers, Software and Manuals
21