Enclume FPTS6 Instruction manual

Enclume FIREPLACE TOOL RACK
FPTS6
Enclume fireplace tool sets are the ultimate in
quality, design, strength and function.
Congratulations for owning one of the finest
fireplace tool sets made.
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR TOOL SET.
Enclosed you will find everything needed for the assembly
and use of your fireplace tool set.
Hardware included:
6- 3/8 x 16 x 5/8 Buttonhead Screws
3- Hard Glides
1-7/32 Hex Key
Components included:
3- Upright Legs
3- Bottom Angled Brackets
3- Top Angled Bracket
1- Broom
1- Shovel
1 - Poker
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
It is important that your rack is assembled correctly. If the unit is assembled or
used incorrectly, it could become unstable and collapse, possibly causing injury.
.
WARNING
Natural broom straw is flammable. Keep the broom well away from open flame.
It should not be used to sweep hot coals or ash
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com
NorthlineExpress.com www.NorthlineExpress.com Toll-FreeToll-Free 1-877-734-2458 NorthlineExpress.com www.NorthlineExpress.com

Instructions for Assembling
the FPTS6 Fireplace Tool Rack
Rack Assembly
1) Using a 5/8" buttonhead screw, secure two of the top angle brackets to the upright legs by positioning the brackets so that the
notch is on top. Place one bracket on each side of the upright leg. Then insert the buttonhead through the large hole on the top
angle bracket, the hole in the upright leg and screw into the threaded hole in the other top angle bracket. Do not tighten fully at
this point.
2) Repeat this step for all of the upright legs and top angle brackets.
3) Turn the rack over so that the top angle brackets are now resting on the floor. Secure the bottom angle brackets in the same
fashion as the top angle brackets. Do not fully tighten at this point.
4) Install the hard glides onto the upright legs by sliding them onto the upright leg bottom.
5) Turn the rack back to its upright position.
6) Square up your rack and tighten all buttonhead screws using the hex key supplied.
7) Hang all tools. Your rack is now complete.
8) All of our hammered steel racks are finished with an industrial acrylic finish to give years of protection to the rack. Cleaning is
easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax
product.
It is important that your rack is assembled correctly. If the unit is assembled or
used incorrectly, it could become unstable and collapse, possibly causing injury.
.
WARNING
Natural broom straw is flammable. Keep the broom well away from open flame.
It should not be used to sweep hot coals or ash
Limited Warranty:This product is warranted to be free of material defects for a period of five year from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PORPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com
Toll-Free 1-866-667-8454
NorthlineExpress.com www.NorthlineExpress.com Toll-Free 1-866-667-8454 NorthlineExpress.com www.NorthlineExpress.com