Enclume Square Pot Rack User manual

SquarePot Rack
THANK YOU VERY MUCH!
We sincerely appreciate your purchase of this kitchen/cookware storage product from Enclume
Design Products, Inc. Enclume is America’s foremost producer of premium-grade cookware racks.
This pot rack is strong and easy to assemble. It is also the easiest ever to install with new-
technology DRYWALL anchors! We want you to enjoy it for many years to come. Please don’t
hesitate to contact us if you have questions or need assistance.
IMPORTANT!
Enclume is committed to the highest quality in the manufacture of this RACK IT UP pot rack. Each
product has been carefully inspected before shipment.
However, in case there is a problem, PLEASE LET US HELP YOU FIRST. Do not return the item to
the location where you purchased it. Call us and explain what is missing or wrong. We will do our
best to help with any question or problem you have—and as fast as possible.

TIP! SAVE TIME AND HASSLE. PLEASE READ ENTIRE INSTRUCTIONS BEFORE BEGINNING ASSEMBLY.
PAINTABLE - Want a different color? The finish on this pot rack can be spray painted any color. We
recommend Rustoleum “Hammered” colors for their metal-like finishes, however any quality spray-can paint may be
used. See a paint retailer for guidance.
TOOLS NEEDED - Hex wrench, fastener hardware (nuts, bolts) are provided.
STEP 1: LAYOUT PARTS
On a table lay out all parts as shown in the exploded view above.
STEP 2: CONNECT MAIN BODY PARTS
Temporarily connect two rectangle ends (2) by inserting a barrel nut (28B) and barrel bolt (28A) through the top hole on
each side. This will cause body of pot rack to stand on edge.
TIP! It is easiest to attach the pot rack parts when you insert the barrel nut from the INSIDE of the pot rack body, then
turn the barrel bolt(28A) into the nut from the OUTSIDE.
How To Assemble Your Pot Rack
TIP! FIRST, REMOVE PAINT FROM BOLT HOLES. Because the powder coat finish applied at the
factory also adheres to the inside of bolt holes, pushing a bolt through it during assembly may be difficult.
Therefore, before connecting parts, we recommend that you check to see that bolts slip easily through all
holes. If they do not, carefully clear paint from holes in side bars, ends and arms using a small knife.
SECOND, be certain that barrel nuts and bolts screw together easily BEFORE beginning assembly. Resi-
due from the black finish may cause some bolts to stick a bit, therefore use the two hex wrenches enclosed
(one for each end of the barrel) and screw them together to clear away extra paint.
MISSING A PART?
Please call our TOLL FREE
SERVICE CENTER
1 [phone]
Item No. Description Qty. Item No Description Qty.
1 Angle arm 2 19A 1/4” bolt hook - 4” 1
2 Rectangle end 2 20 Wood screw hook - 4” 1
5 Hanging bracket 1 25A Pot hook straight 4
28A Barrel bolt 5 25B Pot hook angled 4
28B Barrel Nut 5 26A hex wrench 2
Installation hardware 27A Toggle 1
15 S-Hook 1

STEP 3: ATTACH FIRST ARM
TIP! It is easiest to attach arms when the side of the pot rack to which you are connecting the arm hangs slightly over the edge
of the table. That provides clearance for the flared end that extends below the body of the rack.
Now remove the barrel bolt (28A) from one side and place an angle arm (1) [2-hole end] on the OUTSIDE of the body. Align
the three layers (rectangle ends [2], arm [1] on outside) and reinsert the barrel Bolt (28A) through the upper hole from the OUT-
SIDE.
STEP 4: ATTACH OTHER ARM
Repeat STEP THREE for remaining arm.
STEP 5: HANG TAB
Position hang tab (5) at top of each arm, insert barrel nut/bolt and loosely tighten.
STEP 6: LEVEL POT RACK ON TABLE
Place assembled rack squarely on table and adjust all parts to be certain they are level and straight. Then tighten all bolts
firmly.
You’re now finished and ready to attach to the ceiling!
How to Attach Your Pot Rack to the Ceiling
TOOLS NEEDED:
Provided: Installation hardware (anchors, bolt hook, screw hook, S-hook)
You will need: tape measure, pencil, drill and ½” drill bit, hammer and nail
STEP 1: LOCATION
Decide where you want to place your pot rack. We suggest a location over an island or near your stove and food preparation
area. Also consider the height of the ceiling where the pot rack will hang. (See STEP 2 below.)
On the ceiling, mark a point where the top of rack arms will attach to ceiling bolt hook. Then tap a small nail through the mark
to be certain a joist is not in the way. (NOTE: because your pot rack includes super-strong new-technology anchors, you DO
NOT need to locate and bolt to a ceiling joist. See more info under STEP 3.)
STEP 2: HEIGHT
What is the ideal height for your pot rack? Decide who will be the primary cook using the pot rack. The bottom of your longest
pan (usually a 10” or 12” skillet) should be easily reachable, about 6 inches above the cook’s head. Make sure the cook can
also reach the shortest pots.
This pot rack is designed for a 9-foot ceiling, a common height in many kitchens. If your ceiling is HIGHER than 9 feet, you
may want to consider adding chain to lower the rack to the ideal height.
STEP 3: INSTALL DRYWALL ANCHORS
First, here’s important information about our anchors. RACK IT UP’s new-technology DRYWALL anchor eliminates the need
to bolt your pot rack to a ceiling joist. The steel anchor is very strong and when installed in drywall an anchor holds about 200
lbs., many times the weight you will likely hang from your pot rack.
Plus, since you no longer have to consider the location of a joist which usually determines where your rack has to be installed,
you can position it in drywall anywhere you want!
See YELLOW insert page for Toggle installation.

HANGING ITEMS & CLEANING
Distribute pots and utensils evenly to minimize tipping. If you have purchased an optional grid, heavier items should be
hung on the rack body.
Your pot rack has a durable powder coat finish designed to provide years of protection. Cleaning is done easily using soap
and a damp cloth. Dry thoroughly after cleaning.
______________________________________
ACCESSORIES
These handy add-ons enhance your pot rack.
.
RACK IT UP! 5-Year Limited Warranty
This product is warranted to be free of material defects for a period of five years from the date of purchase.
Customer's exclusive remedy shall be the repair or replacement of the defective product and shall be subject
to the following conditions: (1) notice of any defect is received by Enclume within the warranty period and
(2) customer returns the defective product to Enclume Design Products, Inc., 24 Colwell Street, Port
Hadlock, WA 98339, postage prepaid within 20 days following a return authorization number. (A return au-
thorization number may be obtained from Enclume by calling the number at the bottom of this booklet.) There
are no other warranties expressed or implied.
THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE, INSTALLATION OR USE OF ENCLUME PRODUCTS.
RACK IT UP by Enclume ™ is a trademark of Enclume Design Products, Inc. All rights reserved. Made in China. Packed in the U.S.A.
. ©2008 Enclume Design Products, Inc.
Trim Ceiling Covers (pair)
Place above ceiling hooks to add
“finishing touch” to your pot rack.
Steel, ‘hammered steel” powder coat
finish. Paintable to complement
any décor.
8 Pot Hooks
There’s always a need for extra
hooks. Set of eight hooks
(4 straight, 4 angle). Steel
with powder coat finish for
extra durability.