Enclume LR1A Instruction manual

Enclume Rectangular Firewood Rack
L
R1AandLR1B
Enclume racks are the ultimate in
Storage racks made.
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished with an industrial wax designed to
LR1A give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry
thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"
like wax product.
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – 3/8” x 5/8” Button head screws
2 – 3/8” x ½” Button head screws
1 – 7/32” Allen wrench
4 – Hard Glides
Components included:
2 – Uprights
2 – Legs
2–KindlingHolders LR1B
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
It is important that your rack is assembled correctly. If the unit is
assembled or used incorrectly, it could become unstable and
collapse, possibly causing injury.
WARNING
Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com
NorthlineExpress.com www.NorthlineExpress.com Toll-FreeToll-Free 1-877-734-2458 NorthlineExpress.com www.NorthlineExpress.com

ASSEMBLY AND INSTALLATION INSTRUCTIONS for the LR1A and LR1B
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – 3/8” x 5/8” Button head screws
2 – 3/8” x ½” Button head screws
1 – 7/32” Allen wrench
4 – Hard Glides
Components included:
2 – Uprights
2 – Legs
2 – Kindling Holders
HardGlides
Rack Assembly:
1) Slip the floor glides over the end of the legs.
2) Align the two upright body pieces so the two kindling holders are at the same end.
3) Place the uprights on top and perpendicular to the legs. Using the Allen wrench and the four 3/8” x
5/8” button head screws, attach the legs and the uprights together. The screws should be inserted from
the top down toward the floor. Tighten the screws only finger tight.
4) Attach the two kindling holders to the uprights using the 3/8” x ½” button head screws
5) Square up your rack and tighten all the screws firmly.
6) All of our hammered steel racks are finished with an industrial wax designed to give years of protection
to the rack. Cleaning is easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is
ever needed we recommend a “Pledge” like wax product.
It is important that your rack is assembled correctly. If the unit is assembled or
used incorrectly, it could become unstable and collapse, possibly causing injury
WARNING
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com
Toll-Free 1-866-667-8454
NorthlineExpress.com www.NorthlineExpress.com Toll-Free 1-866-667-8454 NorthlineExpress.com www.NorthlineExpress.com