Vivo MOUNT-REC01 User manual

Recessed TV Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-rec01
SKU: MOUNT-REC01
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
110lbs
(50kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x1)
Mount
B (x1)
Arm
C (x2)
Bracket Rail
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D (x2)
VESA Bracket
E (x4)
Cable Management
Clip
F (x2)
Cable Grommet
T-B (x1)
Bubble Level
G (x4)
Spacer Block
T-A (x1)
4mm Allen Wrench
S-A (x4)
M4x6mm Screw
S-B (x2)
M6x12mm Screw
M-A (x4)
M4x12mm Screw
M-B (x4)
M4x30mm Screw
M-C (x4)
M5x12mm Screw
M-D (x4)
M5x30mm Screw
M-E (x4)
M6x12mm Screw
M-F (x4)
M6x30mm Screw
W-A (x12)
M8x30mm Screw
W-B (x12)
Concrete Anchor
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected]om, or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
H (x4)
Adhesive Pad
M-G (x4)
M8x16mm Screw
M-H (x4)
M8x30mm Screw
M-I (x4)
M6 Washer
M-J (x4)
M8 Spacer
W-C (x12)
M8 Washer

3
ASSEMBLY STEPS
STEP 1 (Option A)
Wood Stud Installation
Find stud locations using a stud finder and mark the edge of each stud. Hold the mount up between two
studs at the desired height with the back side touching the wall and trace the perimeter using a pencil.
Cut and remove the drywall section. Place Mount (A) in the wall and mark all six of the mounting
holes on the le stud using a pencil. The mount can be removed prior to drilling the marked holes.
Using a 3mm (1/8”) drill bit, drill marked holes approximately 30mm (1.2”) deep. Install Mount (A) to
the le stud in the two center mounting holes using M8x30mm Screws (W-A), M8 Washers (W-C), and a
13mm socket wrench. Install Cable Grommets (F) to top and bottom of Mount (A).
TOOLS NEEDED
Stud Finder
Tape Measure Drill
Phillips
Screwdriver
Pencil
3mm Drill
Bit
10mm Drill
Bit 13mm Socket
Drywall Saw
3mm
30mm(1.2)
(0.12)
A
W-A
W-CW-C F
T-B

4
STEP 1 (Option B)
Concrete/Brick Installation
Find the edges the concrete/brick pillar. If covered in drywall, hold Mount (A) with Bubble Level (T-B) up
to the desired mounting location with the back side touching the wall and trace the perimeter using a
pencil. Cut and remove the drywall section. Mark all six of the mounting holes on the le pillar using
a marker then remove mount from from the wall. Using a 10 mm (3/8”) drill bit, drill mounting holes
approximately 60mm (2.4”) deep. Insert Concrete Anchors (W-B) into all of the drilled holes. Place
Mount (A) back into the wall and install to the le pillar using the two center mounting holes, M8x30mm
Screws (W-A), M8 Washers (W-C), and a 13mm socket wrench. Install Cable Grommets (F) to top and
bottom of Mount (A).
10mm
60mm(2.4)
(0.39)
STEP 2 (Option A)
A
W-B
W-A
W-CW-C F
W-CW-C
W-A
T-A
B
A
T-B
Wood Stud Installation
Slide the tabs on the le side of Arm (B) into the slots on Mount (A). Loosen the screws on Arm (B) using
4mm Allen Wrench (T-A). Extend the arms until it reaches the right stud. Make sure the arm is level then
tighten screws. Mark all 4 of the mounting holes on the right stud using a pencil. The mount can be
removed prior to drilling the marked holes. Using a 3mm (1/8”) drill bit, drill mounting holes
approximately 30mm (1.2”) deep. Secure Arm (B) to both pillars
using M8x30mm Screws (W-A), M8 Washers
(W-C), and a 13mm socket wrench.

5
STEP 3 (Optional)
Power Receptacle Installation
If installing a power receptacle, remove the square plate by bending the metal back and forth. Attach
Adhesive Pads (H) to Spacer Blocks (G) and then onto Mount (A) oset from the cutout. We recommend
using a recessed outlet receptacle to provide more space for device plugs.
H
G
A
STEP 2 (Option B)
W-CW-C
W-A
T-A
B
A
Concrete/Brick Installation
Slide the tabs on the le side of Arm (B) into the slots on Mount (A). Loosen the screws on Arm (B) using
4mm Allen Wrench (T-A). Extend the arms until it reaches the right pillar. Make sure the arm is level then
tighten screws. Mark all 4 mounting holes on right pillar using a marker. Loosen the screws on Arm (B)
and remove Arm (B) from Mount (A). Using a 10 mm (3/8”) drill bit, drill mounting holes approximately
60mm (2.4”) deep. Insert Concrete Anchors (W-B) into all of the drilled holes. Reinstall Arm (B) to Mount
(A) and tighten screws on Arm (B) using 4mm Allen Wrench (T-A).
Secure Arm (B) to both pillars using M8x30mm
Screws (W-A), M8 Washers (W-C), and a
13mm socket wrench.

6
STEP 5 (Option A)
Flat Back Monitor
Attach VESA Brackets (D) to the back of the TV using combination of Screws (M-A through M-H) and M6
Washers (M-I). Spacers (M-J) may be required. Tighten with a Phillips screwdriver.
X
TVTV TV
D
M-A
Through
M-H
M-I
M-A
Through
M-H
M-I
M-J
STEP 4
Secure Bracket Rails (C) to Arm (B) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A). Insert
M4x6mm Screws (S-A) into the back of Bracket Rails (C) using a Phillips screwdriver.
C
B
S-B
S-A
T-A
OROR

7
STEP 6
Hang the TV with VESA Brackets (D) onto Bracket Rails (C).
STEP 7
Flip the latch on the underside of VESA Brackets (D) and tighten the security screws using a Phillips
screwdriver to secure them in place. Install Cable Managment Clips (E) onto Arm (B) and route cables
through the clips and Cable Grommets (F).
D
C
D
E
B
F

LAST UPDATED: 01/31/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303