General Description
Trademarks:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy, and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense
*Shielded interface cables must be used in order to comply with emission limits
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance could affect the user's authority to operate the equipment.
Copyright _ 1999 All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written
consent from the company.
The device is a powerful, high-performance Fast Ethernet switch, with all 16 ports
capable of 10 or 100Mbps auto-negotiation operation (Nway) which means the switch
could automatically negotiate with the connected partners on the network speed and
duplex mode. It is ideal for micro-segmenting large networks into smaller, connected
subnets for improved performance, enabling the bandwidth demanding multimedia and
imaging applications. Moreover, the 10/100Mbps auto-sensing ability provides an easy
way to migrate 10Mbps to 100Mbps network with no pain. Compared to the shared
10Mbps or 100Mbps networks, the Ethernet Switch delivers a dedicated 10/100Mbps
connection to every attached client with no bandwidth congestion issue.
Product Features
Rear panel ports
Complies with 10BASE-T specifications of the IEEE802.3 standard
Complies with 100BASE-TX specifications of the IEEE802.3u standard
RJ-45 ports for 100Base-TX and 10Base-T connectivity
Supports Nway protocol for speed (10/100Mbps) and duplex mode
(Half/Full) auto-detection
Supports full and half duplex operation on all ports
Supports back-pressure (half duplex) and flow control (IEEE802.3x)
Wire speed packet filtering and forwarding rate
Store-and-forward architecture filters fragment & CRC error packets
Supports extensive LED indicators for network diagnostics
External power adapter
Supports MDI/MDI-X auto crossover
Power Connecting
Plug the circle end of the power adapter firmly into the power port on the switch rear
panel, and the other end into an electric service outlet, then the system is ready.
Connecting computers to the switch
The switch features auto-MDI/MDIX crossover detection function and provides plug-and-
play capability. Users can immediately use any of the features of this product simply by
plugging the network cables (RJ-45) into the computers and the switch.
Uplink
All Ports can be used as an uplink port for connecting to another unit without using
crossover cable. When using the uplink port, you can extend the distance to 100m for
linking another switch or hub.
*Use only the AC power adapter that came with the switch to prevent damage to the unit
To prolong the operational life of your units
Never stack units more than eight high if freestanding
Do not place objects on top of any unit or stack
Do not obstruct any vents at the sides of the case
Ports 1x - 16x :The switch has sixteen 10/100Mbps RJ-45 ports where you can connect
computers or network devices to the switch.
AC IN : This port connects the AC power adapter.
All trade names and trademarks are the properties of their respective companies.
FCC Warning
01 02
03
Package contents
16 port 10/100Mbps Ethernet Switch
AC power adapter
Quick installation guide
*If any of the items is damaged or missing, please contact your retailer immediately.
Front panel LED indicators
After installing the switch, you can check its status from the LED indicators on the front
panel shown below.
LED Color Status Indication
POWER (PWR) GREEN ON The switch is power on
OFF The switch is power off
LINK / ACT GREEN ON A link is established
BLINKING A link is established and data is being
transmitted or received
PN 2042070000011
[][]
5x 4x 3x 2x 1x15x 14x 13x 12x 11x 10x 9x 8x 7x 6x
ACIN
16x
16 Port 10/100Mbps Ethernet Switch
ENH916P-NWY
