Endress+Hauser Cerabar S PMP75 Technical specifications

KA01025P/00/EN/15.14
71254315
Brief Operating Instructions
Cerabar S
PMC71, PMP71, PMP75
Process pressure measurement
These Instructions are Brief Operating Instructions; they do not replace the
Operating Instructions included in the scope of supply.
For detailed information, refer to the Operating Instructions and other
documentation on the CD-ROM provided or visit
"www.endress.com/deviceviewer".

Table of contents Cerabar S FOUNDATION Fieldbus
2Endress+Hauser
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Installation, commissioning and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Operational safety and process safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.5 Safety icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Product identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 General installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Installation instructions for devices without diaphragm seals PMP71, PMC71 . . . . . . . . . . . . . . . . . . . . . . 5
3.3 Installation instructions for devices with diaphragm seals PMP75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Assembling and mounting the "separate housing" version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Connecting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 Onsite display (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3 Onsite operation via onsite display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.4 Locking/unlocking operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.1 Commissioning via an FF configuration program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6.2 Selecting the language and measuring mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.3 Position adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.4 Pressure measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.5 Level measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.6 Scaling the OUT parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Cerabar S FOUNDATION Fieldbus Safety instructions
Endress+Hauser 3
1 Safety instructions
1.1 Designated use
The Cerabar S is a pressure transmitter for measuring pressure and level.
The manufacturer accepts no liability for damages resulting from incorrect use or use other than
that designated.
1.2 Installation, commissioning and operation
• The device must only be installed, connected, commissioned and maintained by qualified and
authorized specialists (e.g. electrical technicians) in full compliance with the instructions in
this manual, the applicable norms, legal regulations and certificates (depending on the
application).
• The specialist must have read and understood this manual and must follow the instructions it
contains. If you are unclear on anything in these Brief Operating Instructions, you must read
the Operating Instructions (on the CD-ROM). The Operating Instructions provide detailed
information on the device/measuring system.
• The device may only be modified or repaired if such work is expressly permitted in the
Operating Instructions (see CD-ROM).
• If faults cannot be rectified, the device must be taken out of service and secured against
unintentional commissioning.
• Do not operate damaged devices. Mark them as defective.
1.3 Operational safety and process safety
• Alternative monitoring measures must be taken to ensure operational safety and process safety
during configuration, testing and maintenance work on the device.
• The device is safely built and tested according to state-of-the-art technology and has left the
factory in perfect condition as regards technical safety. The applicable regulations and
European standards have been taken into account.
• Pay particular attention to the technical data on the nameplate.
• Devices for use in hazardous areas are fitted with an additional nameplate. If the device is to
be installed in an explosion hazardous area, then the specifications in the certificate as well as
all national and local regulations must be observed. The device is accompanied by separate
"Ex documentation", which is an integral part of this Operating Instructions. The installation
regulations, connection values and Safety Instructions listed in this Ex document must be
observed. The documentation number of the related Safety Instructions is also indicated on
the additional nameplate.
1.4 Return
Follow the instructions on returning the device as outlined in the Operating Instructions on the
CD-ROM provided.

Product identification Cerabar S FOUNDATION Fieldbus
4Endress+Hauser
1.5 Safety icons
2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is displayed.
For an overview of the technical documentation provided, enter the serial number from the
nameplates in the W@M Device Viewer (www.endress.com/deviceviewer).
3 Installation
3.1 General installation instructions
#Warning!
The process seal is not allowed to press on the process isolating diaphragm as this could affect
the measurement result.
Symbol Meaning
#Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to personal injury,
a safety hazard or destruction of the instrument.
"Caution!
Caution highlights actions or procedures which, if not performed correctly, may lead to personal injury or
incorrect functioning of the instrument.
!Note!
A note highlights actions or procedures which, if not performed correctly, may indirectly affect operation
or may lead to an instrument response which is not planned.

Cerabar S FOUNDATION Fieldbus Installation
Endress+Hauser 5
!Note!
• If a heated Cerabar S is cooled during the cleaning (e.g. by cold water), a vacuum develops
for a short time, whereby water can penetrate the sensor through the pressure compensation
(1). If this is the case, mount the sensor with the pressure compensation (1) pointing
downwards.
• Keep the pressure compensation and GORE-TEX®filter (1) free from contaminations.
• Do not clean or touch process isolating diaphragm of the diaphragm seals with hard or pointed
objects.
• Due to the orientation of the Cerabar S, there may be a shift in the measured value, i.e. when
the container is empty, the measured value does not display zero. You can correct this zero
point shift either via the "zero" key on the electronic insert, or on the outside of the device or
via the onsite display. ä15, Section 5.2.1 "Position of operating elements", ä16,
Section 5.2.2 "Function of the operating elements – onsite display not connected" and
ä25, Section 6.3 "Position adjustment".
• For PMP75, please refer to Section 2.3 "Installation instructions for devices with diaphragm
seals", ä7.
• The PMC71 High temperature version and the PMP75 must only be insulated up to a certain
height.
• To ensure optimal readability of the onsite display, it is possible to rotate the housing up to
380°.
• The onsite display can be rotated in 90° stages.
• Endress+Hauser offers a mounting bracket for installing on pipes or walls.
3.2 Installation instructions for devices without diaphragm seals
PMP71, PMC71
Cerabar S without diaphragm seal are mounted as per the norms for a manometer
(DIN EN 837-2). We recommend the use of shutoff devices and siphons. The orientation
depends on the measuring application.
1
1
1
FIELD TERMINALSFIELD TERMINALS
FIELD TERMINALS

Installation Cerabar S FOUNDATION Fieldbus
6Endress+Hauser
3.2.1 Pressure measurement
Pressure measurement in gases
• Mount Cerabar S with shutoff device above the tapping point so that the condensate can flow
into the process.
Pressure measurement in steams
• Mount Cerabar S with siphon above the tapping point.
The siphon reduces the temperature to almost ambient temperature.
• Fill the siphon with fluid before commissioning.
Pressure measurement in liquids
• Mount Cerabar S with shutoff device below or at the same level as the tapping point.
3.2.2 Level measurement
• Mount Cerabar S below the lowest measuring point.
• Do not mount the device at the following positions:
In the fill flow, in the tank outlet or at a point in the container which could be affected by
pressure pulses from an agitator.
• The calibration and functional test can be carried out more easily if you mount the device after
a shutoff device.

Cerabar S FOUNDATION Fieldbus Installation
Endress+Hauser 7
3.3 Installation instructions for devices with diaphragm seals
PMP75
!Note!
• The diaphragm seal, together with the pressure transmitter, forms a closed, calibrated system,
which is filled through openings in the diaphragm seal and in the measurement system of the
pressure transmitter. The openings are sealed and must not be opened.
• Do not remove the protection of the process isolating diaphragm until shortly before
installation.
• When using a mounting bracket, sufficient strain relief must be ensured for the capillaries in
order to prevent the capillary bending down (bending radius 100 mm).
• Please note that the hydrostatic pressure of the liquid column in the capillary can cause zero
point shift. You can correct this zero point shift either via the "zero" key on the electronic
insert, or on the outside of the device or via the onsite display. ä15, Section 5.2.1
"Position of operating elements", ä16, Section 5.2.2 "Function of the operating elements
– onsite display not connected" and ä25, Section 6.3 "Position adjustment".
• Please note the application limits of the diaphragm seal filling oil as detailed in the Technical
Information for TI00383P, Section "Planning instructions for diaphragm seal systems" or at
"www.endress.com/applicator".
In order to obtain more precise measurement results and to avoid a defect in the device, mount
the capillaries as follows:
• vibration-free (in order to avoid additional pressure fluctuations)
• not in the vicinity of heating or cooling lines
• insulate if the ambient temperature is below ore above the reference temperature
• with a bending radius of 100 mm.

Installation Cerabar S FOUNDATION Fieldbus
8Endress+Hauser
3.3.1 Vacuum application
For applications under vacuum, Endress+Hauser recommends mounting the pressure
transmitter underneath the diaphragm seal. A vacuum load of the diaphragm seal caused by the
presence of filling oil in the capillary is hereby prevented.
When the pressure transmitter is mounted above the diaphragm seal, the maximum height
difference H1 in accordance with the illustration below on the left must not be exceeded. The
maximum height difference is dependent on the density of the filling oil and the smallest ever
pressure that is permitted to occur at the diaphragm seal (empty container), see illustration
below, on the right.
P01-PMx7xxxx-11-xx-xx-xx-008
Fig. 1: Installation above the diaphragm seal
P01-PMP75xxx-05-xx-xx-xx-010
Fig. 2: Diagram of maximum installation height above the
diaphragm seal for vacuum applications dependent on the
pressure at the diaphragm seal
H1
FIELDTERMINALSFIELDTERMINALS
0.0
2.0
4.0
6.0
8.0
10.0
12.0
50 100 300 400 500 600 700 800 900 1000
200
Inert oil
High temperature
oil
Vegetable oil
Silicone oil
Pressure, diaphragm seal positive side [mbarabs]
Height difference H1[m]
Low temperature oil

Cerabar S FOUNDATION Fieldbus Installation
Endress+Hauser 9
3.4 Assembling and mounting the "separate housing" version
P01-PMx7xxxx-11-xx-xx-xx-011
Fig. 3: "Separate housing" version
1 In the "separate housing" version, the sensor is supplied with process connection and cable fitted.
2 Cable with connection jack
3 Pressure compensation
4Plug
5Lockingscrew
6 Housing fitted with housing adapter, included
7 Mounting bracket suitable for wall and pipe mounting, included
Assembly and mounting
1. Connect plug (item 4) into the corresponding connection jack of the cable (item 2).
2. Plug the cable into the housing adapter (item 6).
3. Tighten the locking screw (item 5).
4. Mount the housing on a wall or pipe using the mounting bracket (item 7).
When mounting on a pipe, tighten the nuts on the bracket uniformly with a torque of at
least 5 Nm.
Mount the cable with a bending radius (r) 120 mm.
r³120 (4.72)
mm (in)
1
2
3
4
5
6
7

Wiring Cerabar S FOUNDATION Fieldbus
10 Endress+Hauser
4 Wiring
#Warning!
• If the operating voltage is > 35 VDC: Dangerous contact voltage at terminals.
Risk of electric shock!
In a wet environment, do not open the cover if voltage is present.
• Risk of electric shock and/or explosion! Switch off the supply voltage before connecting the
device.
• When using the measuring device in hazardous areas, installation must comply with the
corresponding national standards and regulations and the Safety Instructions or Installation or
Control Drawings.
4.1 Connecting the device
!Note!
• Devices with integrated overvoltage protection must be grounded.
• Protective circuits against reverse polarity, HF influences and overvoltage peaks are installed.
• The supply voltage must match the supply voltage on the nameplate.
• Switch off the supply voltage before connecting the device.
• Remove housing cover of the terminal compartment.
• Guide cable through the gland. Preferably use twisted, shielded two-wire cable.
• Connect device in accordance with the following diagram.
• Screw down housing cover.
• Switch on supply voltage.

Cerabar S FOUNDATION Fieldbus Wiring
Endress+Hauser 11
P01-xMx7xxxx-04-xx-xx-xx-009
Fig. 4: Electrical connection FOUNDATION Fieldbus, observe also the following section.
For devices with 7/8" plug see Operating Instructions.
1Housing
2 Internal ground terminal
3 External ground terminal
4 Supply voltage, for version in non-hazardous area = 9 to 32 V DC
5 Devices with integrated overvoltage protection are labeled OVP (overvoltage protection) here.
4.2 Connecting the measuring unit
!Note!
For further information on the network structure and grounding and for further bus system
components such as bus cables, see the relevant documentation, e.g. Operating Instructions
BA00013S "FOUNDATION Fieldbus Overview" and the FOUNDATION Fieldbus Guideline.
4.2.1 Supply voltage
• Version for non-hazardous area: 9 to 32 V DC
4.2.2 Current consumption
15.5 mA ±1 mA, switch-on current corresponds to IEC 61158-2, Clause 21.
4.2.3 Cable specification
• Use a twisted, shielded two-wire cable, preferably cable type A
• Terminals for wire cross-sections: 0.5 to 2.5 mm2
• Outer cable diameter: 5 to 9 mm
➀
➁
➂
➃
➄
FF FF
FF FF

Wiring Cerabar S FOUNDATION Fieldbus
12 Endress+Hauser
!Note!
For further information on the cable specifications, see Operating Instructions BA00013S
"FOUNDATION Fieldbus Overview", FOUNDATION Fieldbus Guideline and IEC 61158-2
(MBP).
4.2.4 Grounding and shielding
Cerabar S must be grounded, for example by means of the external ground terminal.
Different grounding and shielding installation methods are available for FOUNDATION Fieldbus
networks such as:
• Isolated installation (see also IEC 61158-2)
• Installation with multiple grounding
• Capacitive installation

Cerabar S FOUNDATION Fieldbus Operation
Endress+Hauser 13
5 Operation
5.1 Onsite display (optional)
A 4-line liquid crystal display (LCD) is used for display and operation. The onsite display shows
measured values, dialog texts, fault messages and notice messages.
The display of the device can be turned in 90° steps.
Depending on the installation position of the device, this makes it easy to operate the device and
read the measured values.
The onsite display is available in English. Needless to say, the device can also be operated in 6
languages (de, en, fr, es, jp, ch) via the DTM or EDD. The FieldCare program is an E+H DTM
operating tool and can be acquired from endress.com.
P01-xxxxxxxx-07-xx-xx-xx-011
E
+
–
Bargraph
Operating keys
Symbol
Bargraph
ValueFunction name
Unit
Header line
Information
line
Main line
Parameter
Identification
number
Editing modes
Selection
options
Value that
can be edited
Current measured value
Measured value display

Operation Cerabar S FOUNDATION Fieldbus
14 Endress+Hauser
The following table illustrates the symbols that can appear on the onsite display. Four symbols
can occur at one time.
Symbol Meaning
Alarm symbol
– Symbol flashing: warning, device continues measuring.
– Symbol permanently lit: error, device does not continue measuring.
Note: The alarm symbol may overlie the tendency symbol.
Lock symbol
The operation of the device is locked. Unlock device, ä21, Section 5.4.
Communication symbol
Data transfer via communication
Simulation symbol
Simulation mode is activated. DIP switch 2 for simulation is set to "On".
ä15, Section 5.2.1 "Position of operating elements".
Tendency symbol (increasing)
The primary value of the Transducer Block is increasing.
Tendency symbol (decreasing)
The primary value of the Transducer Block is decreasing.
Tendency symbol (constant)
The primary value of the Transducer Block has remained constant over the past few minutes.

Cerabar S FOUNDATION Fieldbus Operation
Endress+Hauser 15
5.2 Operating elements
5.2.1 Position of operating elements
With regard to aluminum housings and stainless steel housing (T14/T15), the operating key is
located either outside the device under the protection cap or inside on the electronic insert. In
hygienic stainless housings (T17), the operating key is always located inside on the electronic
insert. Additionally, three operating keys are located on the optional onsite display.
P01-PMx7xxxx-19-xx-xx-xx-075
Fig. 5: Operating key, external under the protective flap
1 Operating key or position adjustment (zero
point-correction) or total reset
P01-xxxxxxxx-19-xx-xx-xx-106
Fig. 6: Operating key and operating elements, internal
1 Green LED to indicate value is accepted
2 Operating key for position adjustment (zero
point-correction)
3 Slot for optional display
4 Slot for optional HistoROM®/M-DAT
5 DIP-switch for locking/unlocking
measured-value-relevant parameters
6 DIP switch for simulation mode
➀
0%
Zero
HW
21
PC
12
➀➁
➃
on
off
➂
➄➅
Sim.
Sensor
on
off
Simulation
0%
Zero
Display
HistoROM

Operation Cerabar S FOUNDATION Fieldbus
16 Endress+Hauser
5.2.2 Function of the operating elements – onsite display not connected
5.2.3 Function of the operating elements – onsite display connected
Operating key(s) Meaning
P02-xxxxxxxx-19-xx-xx-xx-107
– Position adjustment (zero point correction): Press key for at least 3 seconds. The
LED on the electronic insert lights up briefly if the pressure applied has been
accepted for position adjustment.
ä32 ("Level" measuring mode) or ä27 ("Pressure" measuring mode).
– Total reset: Press key for at least 12 seconds. If the LED on the electronic insert
lights up briefly, the reset is being carried out.
P01-xxxxxxxx-19-xx-xx-xx-134
– DIP-switch 1: for locking/unlocking measured-value-relevant parameters
Factory setting: off (unlocked)
– DIP switch 2: for simulation mode
Factory setting: off (simulation mode off)
To carry out a simulation the DIP switch has to be set in the "on" position. See
also Operating Instructions BA00302P, Section "Simulation".
Operating key(s) Meaning
O– Navigate upwards in the picklist
– Edit the numerical values and characters within a function
S– Navigate downwards in the picklist
– Edit the numerical values and characters within a function
F–Confirmentry
– Jump to the next item
Oand FContrast setting of onsite display: darker
Sand FContrast setting of onsite display: brighter
O and S
ESC functions:
– Exit edit mode without saving the changed value.
– You are in a menu within a function group. The first time you press the keys
simultaneously, you go back a parameter within the function group. Each time you
press the keys simultaneously after that, you go up a level in the menu.
– You are in a menu at a selection level. Each time you press the keys simultaneously,
you go up a level in the menu.
Note: The terms function group, level and selection level are explained in ä17,
Section 5.3.1.
0%
Zero
12
on
off
Sim.

Cerabar S FOUNDATION Fieldbus Operation
Endress+Hauser 17
5.3 Onsite operation via onsite display
5.3.1 Structure of the operating menu
The menu is split into four levels. The three upper levels are used to navigate while you use the
bottom level to enter numerical values, select options and save settings. For the entire menu
see CD-ROM, Operating Instructions BA00302P.
The structure of the OPERATING MENU depends on the measuring mode selected, e.g. if the
"Pressure" measuring mode is selected, only the functions necessary for this mode are displayed.
P01-xxxxxxxx-19-xx-xx-xx-145
Fig. 7: Structure of the operating menu
1 1. Selection level
2 2. Selection level
3Functiongroups
4 Parameter
➀
➂
➁
➃
Measured value
GROUP SELECTION
DISPLAYSETTINGS
EXTENDED SETUP
POS. ZERO ADJUST
POS. INPUT VALUE
CALIB. OFFSET
POSITION ADJUSTMENT BASIC SETUP
OPERATING MENU
QUICK SETUP
MEASURING MODELANGUAGE

Operation Cerabar S FOUNDATION Fieldbus
18 Endress+Hauser
5.3.2 Selecting an option
Example: Selecting the "Pressure" measuring mode.
5.3.3 Editing a value
Example: adjusting DAMPING VALUE function from 2.0 s to 30.0 s. ä16, Section 5.2.3
"Function of the operating elements – onsite display connected".
Onsite display Operation
P01-xxxxxxxx-19-xx-xx-en-017
"Level" has been selected as the measuring mode. A ✓in
front of the menu text indicates the active option.
P01-xxxxxxxx-19-xx-xx-en-033
Use "+" or "–" to select "Pressure" as the operating mode.
P01-xxxxxxxx-19-xx-xx-en-034
1. Confirm your choice with "E". A ✓in front of the
menu text indicates the active option. (The "Pressure"
measuring mode is selected.)
2. Jump to the next item with "E".
Onsite display Operation
P01-xxxxxxxx-19-xx-xx-xx-023
The onsite display shows the parameter to be changed. The
value highlighted in black can be changed. The "s" unit is
fixed and cannot be changed.
P01-xxxxxxxx-19-xx-xx-xx-027
1. Press "+" or "–" to get to the editing mode.
2. The first digit is highlighted in black.

Cerabar S FOUNDATION Fieldbus Operation
Endress+Hauser 19
P01-xxxxxxxx-19-xx-xx-xx-028
1. Use "+" to change "2" to "3".
2. Confirm "3" with "E". The cursor jumps to the next
position (highlighted in black).
P01-xxxxxxxx-19-xx-xx-xx-029
The decimal point is highlighted in black, i.e. you can now
edit it.
P01-xxxxxxxx-19-xx-xx-xx-030
1. Keep pressing "+" or "–" until "0" is displayed.
2. Confirm "0" with "E".
The cursor jumps to the next position.  is displayed
and is highlighted in black. See next graphic.
P01-xxxxxxxx-19-xx-xx-xx-031
Use "E" to save the new value and exit the editing mode.
See next graphic.
P01-xxxxxxxx-19-xx-xx-xx-032
The new value for the damping is now 30.0 s.
– Jump to the next parameter with "E".
– You can get back to the editing mode with "+" or "–".
Onsite display Operation

Operation Cerabar S FOUNDATION Fieldbus
20 Endress+Hauser
5.3.4 Taking pressure applied at device as value
Example: performing position adjustment.
Onsite display Operation
P01-xxxxxxxx-19-xx-xx-xx-158
The bottom line on the onsite display displays the pressure
present, here 3.9 mbar.
P01-xxxxxxxx-19-xx-xx-xx-159
Use "+" or "–" to switch to the "Confirm" option. The
active selection is highlighted in black.
P01-xxxxxxxx-19-xx-xx-xx-037
Use "E" to assign the value (3.9 mbar) to the POS. ZERO
ADJUST parameter. The device confirms the calibration
and jumps back to the parameter, here POS. ZERO
ADJUST (see next graphic).
P01-xxxxxxxx-19-xx-xx-xx-160
Switch to the next parameter with "E".