Endress+Hauser Micropilot FMR10 Technical specifications

Products Solutions Services
Brief Operating Instructions
Micropilot FMR10
Free space radar
These Instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
For detailed information, refer to the Operating Instructions
and other documentation.
Available for all device versions via:
• Internet: www.endress.com/deviceviewer
• Smart phone/Tablet: Endress+Hauser Operations App
KA01247F/00/EN/02.16
71331349
2020-03-30

Micropilot FMR10
2 Endress+Hauser
1.
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
2.
3.
A0023555

Micropilot FMR10 Table of contents
Endress+Hauser 3
Table of contents
1 About this document .............................................................. 4
1.1 Symbols used ......................................................................... 4
1.2 Documentation ........................................................................ 5
1.3 Supplementary documentation ............................................................ 5
1.4 Registered trademarks .................................................................. 5
2 Basic safety instructions .......................................................... 5
2.1 Requirements for personnel .............................................................. 5
2.2 Designated use ........................................................................ 6
2.3 Workplace safety ...................................................................... 6
2.4 Operational safety ......................................................................7
2.5 Product safety ......................................................................... 7
3 Product description ............................................................... 8
3.1 Product design ........................................................................ 8
4 Incoming acceptance and product identification ................................... 8
4.1 Goods acceptance ...................................................................... 8
4.2 Product identification ................................................................... 8
4.3 Manufacturer address ................................................................... 9
4.4 Nameplate .......................................................................... 10
5 Installation ...................................................................... 12
5.1 Installation conditions .................................................................. 12
5.2 Post-installation check ................................................................. 20
6 Electrical connection ............................................................ 21
6.1 Cable assignment ..................................................................... 21
6.2 Supply voltage ....................................................................... 21
6.3 Connecting the device .................................................................. 22
6.4 Post-connection check ..................................................................22
7 Operability ...................................................................... 23
7.1 Operating concept ..................................................................... 23
7.2 Operation via Bluetooth® wireless technology ................................................ 23
8 Commissioning and operation ................................................... 23
8.1 Commissioning via SmartBlue (App) ....................................................... 23
9 Diagnostics and troubleshooting ................................................. 26
9.1 General errors ........................................................................ 26
9.2 Error - SmartBlue operation ............................................................. 26
9.3 Diagnostic event in the operating tool ...................................................... 27

About this document Micropilot FMR10
4 Endress+Hauser
1 About this document
1.1 Symbols used
1.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Symbols for certain types of information and graphics
Permitted
Procedures, processes or actions that are permitted
Forbidden
Procedures, processes or actions that are forbidden
Tip
Indicates additional information
Reference to documentation
Reference to graphic
Notice or individual step to be observed
1.
,
2.
,
3.
Series of steps
Result of a step
Operation via operating tool
Write-protected parameter
1, 2, 3, ...
Item numbers

Micropilot FMR10 Basic safety instructions
Endress+Hauser 5
A, B, C, ...
Views
1.2 Documentation
The following documentation types are available in the Downloads section of the Endress
+Hauser website (www.endress.com/downloads):
For an overview of the scope of the associated Technical Documentation, refer to the
following:
•W@M Device Viewer (www.endress.com/deviceviewer): Enter the serial number from
nameplate
•Endress+Hauser Operations App: Enter the serial number from the nameplate or scan
the 2D matrix code (QR code) on the nameplate
1.3 Supplementary documentation
BA01577F
Operating Instructions FMR10
1.4 Registered trademarks
Apple®
Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the
U.S. and other countries. App Store is a service mark of Apple Inc.
Android®
Android, Google Play and the Google Play logo are trademarks of Google Inc.
Bluetooth®
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG,
Inc. and any use of such marks by Endress+Hauser is under license. Other trademarks and
trade names are those of their respective owners.
2 Basic safety instructions
2.1 Requirements for personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill the
following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Personnel must be authorized by the plant owner/operator.
‣Be familiar with federal/national regulations.
‣Before starting work: personnel must read and understand the instructions in the manual
and supplementary documentation as well as the certificates (depending on the
application).
‣Personnel must follow instructions and comply with general policies.

Basic safety instructions Micropilot FMR10
6 Endress+Hauser
The operating personnel must fulfill the following requirements:
‣Personnel are instructed and authorized according to the requirements of the task by the
facility's owner-operator.
‣Personnel follow the instructions in this manual.
2.2 Designated use
Application and media
The measuring device described in these Operating Instructions is intended for continuous,
non-contact level measurement in liquids. Because of its operating frequency of approx.
26 GHz, a maximum radiated pulsed power of 5.7 mW and an average power output of
0.015 mW, use outside of closed, metallic vessels is also permitted. If operated outside of
closed vessels, the device must be mounted in accordance with the instructions in the
"Installation" section. Operation of the devices does not pose a risk to health or the
environment.
If the limit values specified in the "Technical data" and the conditions listed in the instructions
and additional documentation are observed, the measuring device may be used for the
following measurements only:
‣Measured process variables: distance
‣Calculated process variables: volume or mass in vessels of any shape; flow through
measuring weirs or channels (calculated from the level by the linearization functionality)
To ensure that the measuring device remains in proper condition for the operation time:
‣Use the measuring device only for media to which the process-wetted materials have an
adequate level of resistance.
‣Observe the limit values (see "Technical data").
Incorrect use
The manufacturer is not liable for damage caused by improper or non-designated use.
Verification for borderline cases:
‣With regard to special media and media used for cleaning, please contact the
manufacturer. Endress+Hauser will be happy to assist in clarifying the corrosion-resistant
properties of wetted materials but does not accept any warranty or liability.
Residual risks
Due to heat transfer from the process as well as power dissipation within the electronics, the
temperature of the electronics housing and the assemblies contained therein may rise to
80 °C (176 °F) during operation. When in operation, the sensor can reach a temperature close
to the medium temperature.
Danger of burns from contact with surfaces!
‣In the event of elevated fluid temperatures, ensure protection against contact to prevent
burns.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.

Micropilot FMR10 Basic safety instructions
Endress+Hauser 7
2.4 Operational safety
Risk of injury!
‣Operate the device only if it is in proper technical condition, free from errors and faults.
‣The operator is responsible for interference-free operation of the device.
Hazardous area
To eliminate the risk of danger to persons or the facility when the device is used in the
approval-related area (e.g. explosion protection, pressure equipment safety):
‣Check the nameplate to verify if the device ordered can be put to its intended use in the
approval-related area.
‣Observe the specifications in the separate supplementary documentation that is an integral
part of this manual.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate. It meets general safety standards and legal requirements.
2.5.1 CE mark
The measuring system meets the legal requirements of the applicable EU Directives. These are
listed in the corresponding EU Declaration of Conformity along with the standards applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
2.5.2 EAC conformity
The measuring system meets the legal requirements of the applicable EAC guidelines. These
are listed in the corresponding EAC Declaration of Conformity together with the standards
applied.
Endress+Hauser confirms successful testing of the device by affixing to it the EAC mark.

Product description Micropilot FMR10
8 Endress+Hauser
3 Product description
3.1 Product design
3.1.1 Micropilot FMR10
18
9
2
3
4 5
6
7
A0028415
 1 Design of the Micropilot FMR10 (26 GHz)
1 Sensor housing
2 Seal
3 Process connection rear side
4 Cable gland
5 Pipe adapter
6 O-ring
7 Counter nut
8 Design ring
9 Process connection front side
4 Incoming acceptance and product identification
4.1 Goods acceptance
Check the following during goods acceptance:
• Are the order codes on the delivery note and the product sticker identical?
• Are the goods undamaged?
• Do the nameplate data match the ordering information on the delivery note?
• If required (see nameplate): Are the safety instructions (XA) provided?
If one of these conditions is not met, please contact the manufacturer's sales office.
4.2 Product identification
The following options are available for the identification of the measuring device:
• Nameplate specifications
• Extended order code with breakdown of the device features on the delivery note

Micropilot FMR10 Incoming acceptance and product identification
Endress+Hauser 9
‣Enter the serial number from the nameplates into W@M Device Viewer
(www.endress.com/deviceviewer)
 All the information about the measuring device and the scope of the associated
Technical Documentation are displayed.
‣Enter the serial number from the nameplate into the Endress+Hauser Operations App or
use the Endress+Hauser Operations App to scan the 2-D matrix code (QR Code) provided on
the nameplate
 All the information about the measuring device and the scope of the associated
Technical Documentation are displayed.
4.3 Manufacturer address
Endress+Hauser SE+Co. KG
Hauptstraße 1
79689 Maulburg, Germany
Address of the manufacturing plant: See nameplate.

Incoming acceptance and product identification Micropilot FMR10
10 Endress+Hauser
4.4 Nameplate
12
11
8
7
6
2
1
3
4
5
19
20
18
15 16
13
17
14
24
Ext. ord. cd.:
Order code:
Ser. no.:
Tp max:
DeviceID:
Date:
ex works
Mat.:
FW: Dev.Rev.:
10
Ta:
if modification
see sep. label
X =
MWP:
23
21
22
9
A0029096
 2 Nameplate of Micropilot
1 Manufacturer address
2 Device name
3 Order code
4 Serial number (ser. no.)
5 Extended order code (ext. ord. cd.)
6 Supply voltage
7 Signal outputs
8 Process pressure
9 Allowable ambient temperature (Ta)
10 Maximum process temperature
11 Device ID
12 Firmware version (FW)
13 Device revision (Dev.Rev.)
14 CE mark
15 Additional information about the device version (certificates, approvals)
16 C-tick
17 Materials in contact with process
18 Degree of protection: e.g. IP, NEMA
19 Certificate symbol
20 Certificate and approval relevant data
21 Document number of the Safety Instructions: e.g. XA, ZD, ZE