Endress+Hauser Proline Promass 83 Parts list manual

BA108D/06/en/11.08
71085231
Valid as of software version:
V 3.02.XX (device software)
Description of Device Functions
Proline Promass 83
MODBUS RS485
Coriolis Mass Flow Measuring System
0000 0001 0002 0003 0004 0005000
AAAA
1000 1001 1002 1003 1004 1005100
BAAB
2000 2001 2002 2003 2004 2005200
CAAC
3000 3001 3002 3003 3004 3005300
DAAD
4000 4001 4002 4003 4004 4005400
EAAE
5000 5001 5002 5003 5004500
FAAF
4200
5200
4201
5201
4202
5202
4203
5203
4204 4205420
520
2400 2401 2402 2403 2404 2405240
CCA
2200 2201 2202 2203 2204 2205220
CBA
0200 0201 0202 0203 0204 0205020
0000 0001 0002 0003 0004 0005000
AAAA
1000 1001 1002 1003 1004 1005100
BAAB
2000 2001 2002 2003 2004 2005200
CAAC
3000 3001 3002 3003 3004 3005300
DAAD
4000 4001 4002 4003 4004 4005400
EAAE
5000 5001 5002 5003 5004500
FAAF
4200
5200
4201
5201
4202
5202
4203
5203
4204 4205420
520
2400 2401 2402 2403 2404 2405240
CCA
2200 2201 2202 2203 2204 2205220
CBA
0200 0201 0202 0203 0204 0205020
1000 1001 10100
BAAB
2000 2001 20200
CAAC
3000 3001 30300
DAAD
4000 4001 40400
EAAE
5000 5001 50500
FAAF
4200
5200
4201
5201
4
5
420
520
2400 2401 24240
CCA
2200 2201 2220
CBA
0200 0201 0020

Device Functions Proline Promass 83 MODBUS
2Endress+Hauser

Device Functions Proline Promass 83 MODBUS
Endress+Hauser 3
Table of contents
1 Using this Manual . . . . . . . . . . . . . . . . . . . . 5
1.1 Finding a function description . . . . . . . . . . . . . . . . . 5
1.1.1 Using the table of contents . . . . . . . . . . . . . 5
1.1.2 Using the graphic of the function matrix . . . 5
1.1.3 Using the index of the function matrix . . . . . 5
2FunctionMatrix. . . . . . . . . . . . . . . . . . . . . . 6
2.1 General layout of the function matrix . . . . . . . . . . . 6
2.1.1 Blocks (A, B, C, etc.) . . . . . . . . . . . . . . . . . . 6
2.1.2 Groups (AAA, AEA, CAA, etc.) . . . . . . . . . . 6
2.1.3 Function groups (000, 020, 060, etc.) . . . . . 6
2.1.4 Functions (0000, 0001, 0002, etc.) . . . . . . . 6
2.1.5 Codes identifying cells . . . . . . . . . . . . . . . . . 7
2.2 Illustration of the function descriptions . . . . . . . . . . 8
2.3 Display lines on the local display . . . . . . . . . . . . . . . 8
2.4 Function matrix Proline Promass 83 . . . . . . . . . . . . 9
3 Block MEASURED VARIABLES . . . . . . . 10
3.1 Group MEASURING VALUES . . . . . . . . . . . . . . . . 11
3.1.1 Function group MAIN VALUES . . . . . . . . . 11
3.1.2 Function group ADDITIONAL VALUES . . . 12
3.2 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . . 15
3.2.1 Function group CONFIGURATION . . . . . . 15
3.2.2 Function group ADDITIONAL
CONFIGURATION . . . . . . . . . . . . . . . . . . 18
4 Block QUICK SETUP . . . . . . . . . . . . . . . . 20
4.1 “Commissioning” Quick Setup menu . . . . . . . . . . 22
4.2 “Batching” Quick Setup menu . . . . . . . . . . . . . . . . 24
4.3 “Pulsating flow” Quick Setup menu . . . . . . . . . . . . 27
4.4 “Gas measurement” Quick Setup menu . . . . . . . . . 29
4.5 “Communication” Quick Setup menu . . . . . . . . . . 30
4.6 Data back-up/transfer . . . . . . . . . . . . . . . . . . . . . . 31
5 Block USER INTERFACE . . . . . . . . . . . . . 32
5.1 Group CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.1.1 Function group
BASIC CONFIGURATION . . . . . . . . . . . . . 33
5.1.2 Function group
UNLOCKING/LOCKING. . . . . . . . . . . . . . 35
5.1.3 Function group OPERATION . . . . . . . . . . . 36
5.2 Group MAIN LINE . . . . . . . . . . . . . . . . . . . . . . . . 37
5.2.1 Function group CONFIGURATION . . . . . . 37
5.2.2 Function group MULTIPLEX . . . . . . . . . . . 39
5.3 Group ADDITIONAL LINE . . . . . . . . . . . . . . . . . . 41
5.3.1 Function group CONFIGURATION . . . . . . 41
5.3.2 Function group MULTIPLEX . . . . . . . . . . . 44
5.4 Group INFORMATION LINE . . . . . . . . . . . . . . . . 47
5.4.1 Function group CONFIGURATION . . . . . . 47
5.4.2 Function group MULTIPLEX . . . . . . . . . . . 50
6 Block TOTALIZER . . . . . . . . . . . . . . . . . 53
6.1 Group TOTALIZER (1 to 3) . . . . . . . . . . . . . . . . . . 54
6.1.1 Function group CONFIGURATION. . . . . . . 54
6.1.2 Function group OPERATION . . . . . . . . . . . 56
6.2 Group HANDLING TOTALIZER . . . . . . . . . . . . . . . 57
7 Block OUTPUTS . . . . . . . . . . . . . . . . . . . 58
7.1 Group CURRENT OUTPUT . . . . . . . . . . . . . . . . . . 59
7.1.1 Function group CONFIGURATION . . . . . . 59
7.1.2 Function group OPERATION . . . . . . . . . . . 67
7.1.3 Function group INFORMATION . . . . . . . . . 67
7.2 Group PULSE/FREQUENCY OUTPUT 1 . . . . . . . . 68
7.2.1 Function group CONFIGURATION. . . . . . . 68
7.2.2 Function group OPERATION . . . . . . . . . . . 89
7.2.3 Function group INFORMATION . . . . . . . . 92
7.3 Group RELAY OUTPUT (1 to 2) . . . . . . . . . . . . . . . 93
7.3.1 Function group CONFIGURATION . . . . . . 93
7.3.2 Function group OPERATION . . . . . . . . . . . 97
7.3.3 Function group INFORMATION . . . . . . . . 98
7.3.4 Information on the response of the
relay output . . . . . . . . . . . . . . . . . . . . . . . . 99
7.3.5 Switching response of the relay output . . . 100
8 Block INPUTS . . . . . . . . . . . . . . . . . . . . . 102
8.1 Group STATUS INPUT . . . . . . . . . . . . . . . . . . . . 103
8.1.1 Function group CONFIGURATION . . . . . 103
8.1.2 Function group OPERATION . . . . . . . . . . 104
8.1.3 Function group INFORMATION . . . . . . . 105
9 Block BASIC FUNCTION . . . . . . . . . . . 106
9.1 Group MODBUS RS485 . . . . . . . . . . . . . . . . . . . 107
9.1.1 Function group CONFIGURATION . . . . . 107
9.2 Group PROCESS PARAMETER . . . . . . . . . . . . . . 109
9.2.1 Function group CONFIGURATION . . . . . 109
9.2.2 Function group EPD PARAMETER . . . . . . 111
9.2.3 Function group
REFERENCE PARAMETER. . . . . . . . . . . . 113
9.2.4 Function group ADJUSTMENT . . . . . . . . 115
9.2.5 Function group
PRESSURE CORRECTION . . . . . . . . . . . . 117
9.3 Group SYSTEM PARAMETER . . . . . . . . . . . . . . . 118
9.3.1 Function group CONFIGURATION . . . . . 118
9.4 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . . 119
9.4.1 Function group CONFIGURATION . . . . . 119
9.4.2 Function group FLOW COEFFICIENT . . . 120
9.4.3 Function group DENSITY COEFFICIENT . 121
9.4.4 Function group
ADDITIONAL COEFFICIENT . . . . . . . . . 122

Device Functions Proline Promass 83 MODBUS
4Endress+Hauser
10 Block SPECIAL FUNCTION . . . . . . . . 123
10.1 Group DENSITY FUNCTIONS . . . . . . . . . . . . . . 125
10.1.1 Function group CONFIGURATION . . . . 125
10.2 Group BATCHING FUNCTION . . . . . . . . . . . . . 131
10.2.1 Function group CONFIGURATION . . . . 131
10.2.2 Function group VALVE PARAMETER . . 138
10.2.3 Examples of setting parameters for
batching processes . . . . . . . . . . . . . . . . . 140
10.2.4 Function group SUPERVISION . . . . . . . . 143
10.2.5 Function group OPERATION . . . . . . . . . 146
10.2.6 Function group INFORMATION . . . . . . 148
10.3 Group ADVANCED DIAGNOSTICS . . . . . . . . . . 149
10.3.1 Function group CONFIGURATION . . . . 149
10.3.2 Function group ACQUISITION . . . . . . . 150
10.3.3 Function group MASS FLOW . . . . . . . . . 151
10.3.4 Function group DENSITY . . . . . . . . . . . 153
10.3.5 Function group REFERENCE DENSITY . 155
10.3.6 Function group TEMPERATURE . . . . . . 157
10.3.7 Function group TUBE DAMPING . . . . . 159
10.3.8 Function group
ELECTRODYNAMIC SENSORS . . . . . . . 161
10.3.9 Function group OPERATING
FREQUENCY FLUCTUATION . . . . . . . . 163
10.3.10Function group TUBE DAMPING
FLUCTUATION . . . . . . . . . . . . . . . . . . 165
11 Block SUPERVISION. . . . . . . . . . . . . . . 167
11.1 Group SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . 168
11.1.1 Function group CONFIGURATION . . . . . 168
11.1.2 Function group OPERATION. . . . . . . . . . 169
11.2 Group VERSION INFO . . . . . . . . . . . . . . . . . . . . 171
11.2.1 Function group DEVICE . . . . . . . . . . . . 171
11.2.2 Function group SENSOR . . . . . . . . . . . . 172
11.2.3 Function group AMPLIFIER . . . . . . . . . . 173
11.2.4 Function group F-CHIP . . . . . . . . . . . . . 174
11.2.5 Function group I/O MODULE . . . . . . . . 175
11.2.6 Function groups
I/O SUBMODULE 2 to 4 . . . . . . . . . . . . 176
12 Factory settings . . . . . . . . . . . . . . . . . . . 178
12.1 SI units (not for USA and Canada) . . . . . . . . . . . . 178
12.1.1 Low flow cut off, full scale value,
pulse value – Liquid . . . . . . . . . . . . . . . . 178
12.1.2 Low flow cut off, full scale value,
pulse value – Gas . . . . . . . . . . . . . . . . . 178
12.1.3 Language . . . . . . . . . . . . . . . . . . . . . . . 179
12.1.4 Density, length, temperature . . . . . . . . . 179
12.2 US units (only for USA and Canada) . . . . . . . . . . 180
12.2.1 Low flow cut off, full scale value,
pulse value – Liquid . . . . . . . . . . . . . . . . 180
12.2.2 Low flow cut off, full scale value,
pulse value – Gas . . . . . . . . . . . . . . . . . 180
12.2.3 Language, density, length, temperature . . 180
Index function matrix . . . . . . . . . . . . . . . . . . 181
Index key words . . . . . . . . . . . . . . . . . . . . . . . 185

Device Functions Proline Promass 83 MODBUS RS485 1 Using this Manual
Endress+Hauser 5
1 Using this Manual
This manual must be used in conjunction with the Operating Instructions of the measuring device.
A description of all the functions of the measuring device is provided here.
1.1 Finding a function description
There are various ways of locating the description of a function of your choice in the manual:
1.1.1 Using the table of contents
The designations of all the cells in the function matrix are listed in the table of contents. You can
use these unambiguous designations (such as USER INTERFACE, INPUTS, OUTPUTS, etc.) to
choose whichever functions are applicable to a particular set of conditions. The page references
show you exactly where to find the detailed descriptions of the functions in question. The table of
contents is on page 3.
1.1.2 Using the graphic of the function matrix
This step-by-step, top-down approach starts with the blocks, the highest level, and factory down
through the matrix to the description of the function you need:
1. All blocks available, and their related groups, are illustrated on Page 9. Select the block (or the
group within the block) which you need for your application and use the page reference to
locate the information corresponding to the next level.
2. The page in question contains a graphic showing of the block with all its subordinate groups,
function groups and functions. Select the function which you need for your application and use
the page reference to locate the detailed function description.
1.1.3 Using the index of the function matrix
Each “cell” in the function matrix (blocks, groups, function groups, functions) has a unique
identifier in the form of a code consisting of one or three letters or a three- or four-digit number.
The code identifying a selected “cell” appears at the top right on the local display.
The function matrix index lists the codes for all the available “cells” in alphabetic and consecutive
order, complete with the page references for the corresponding functions.
A0004821-en
Fig. 1 : Local display
1 Name of the function, e.g. mass flow, user interface
2 Function code, e.g. 0000, CAA
The index to the function matrix is on Page 181.
1212

2 Function Matrix Device Functions Proline Promass 83 MODBUS RS485
6Endress+Hauser
2 Function Matrix
2.1 General layout of the function matrix
The function matrix consists of four levels:
Blocks -> Groups -> Function groups -> Functions
A0000961
Fig. 2 : Layout of the function matrix
2.1.1 Blocks (A, B, C, etc.)
The blocks are the highest-level grouping of the operation options for the device. The blocks
include, for example: MEASURED VARIABLES, QUICK SETUP, USER INTERFACE, TOTALIZER,
etc.
2.1.2 Groups (AAA, AEA, CAA, etc.)
A block consists of one or more groups. Each group represents a more detailed selection of the
operation options in the higher-order block. The groups in the “USER INTERFACE” block, for
example, include: CONTROL, MAIN LINE, ADDITIONAL LINE, etc.
2.1.3 Function groups (000, 020, 060, etc.)
A group consists of one or more function groups. Each function group represents a more detailed
selection of the operation options in the higher-order group. Function groups available of
“CONTROL” group are for example: BASIC CONFIGURATION, UNLOCKING/LOCKING,
OPERATION, etc.
2.1.4 Functions (0000, 0001, 0002, etc.)
Each function group consists of one or more functions. The functions are used to operate and
parameterize the device. Numerical values can be entered or parameters selected and saved.
The functions in the “BASIC CONFIGURATION” function group include LANGUAGE, DISPLAY
DAMPING, CONTRAST LCD, etc. The procedure for changing the language of the user interface,
for example, is as follows:
1. Select the block “USER INTERFACE”.
2. Select the group “CONTROL”.
3. Select the function group “BASIC CONFIGURATION”.
4. Select the function “LANGUAGE”
(here you can set the language required).
…
…
…
…
…
…
…
…
0001
2001
0401
2021
2201
0002
2002
0402
2022
2202
0003
2003
0403
2023
2203
0009
2009
0409
2029
2209
0429
2049
2069
0421
2041
0422
2042
0423
2043
20632061 2062
0000
2000
0400
2020
2200
0420
2040
2060
000
200
040
202
220
042
204
206
AAA
BAA
ACA
CAA
CBA
D, E, …
A
B
C

Device Functions Proline Promass 83 MODBUS RS485 2 Function Matrix
Endress+Hauser 7
2.1.5 Codes identifying cells
Each cell (block, group, function group and function)
in the function matrix has an individual, unique code.
Blocks:
The code is a letter (A, B, C, etc.)
Groups:
The code consists of three letters (AAA, ABA, BAA, etc.).
The first letter matches the block code (i.e. each group in block A
has a code starting with an A _ _; the codes of the
groups in block B start with a B _ _ etc.). The other two letters are for identifying the group
within the respective block.
Function groups:
The code consists of three digits (000, 001, 100, etc.).
Functions:
The code consists of four digits (0000, 0001, 0201, etc.).
The first three digits are the same as the code for the function group.
The last digit in the code is a counter for the functions in the function group, incrementing from 0
to 9 (e.g. function 0005 is the sixth function in group 000).
Block Groups Function groups Functions
A0001251
200020012002200
CAAC

2 Function Matrix Device Functions Proline Promass 83 MODBUS RS485
8Endress+Hauser
2.2 Illustration of the function descriptions
A0004827-en
Fig. 3 : Example for the description of a function
1 Name of the function
2 Number of the function (appears on the local display; is
not identical to the MODBUS RS485 register address)
3 Description of the function
4 Selection or entry options or display
5 Factory setting (the measuring device is delivered with this setting/selected option)
6 Information on communication via MODBUS RS485
– MODBUS RS485 register (information in decimal numerical format)
– Data type: float (length = 4 bytes), integer (length = 2 bytes), string (length = depends on function)
– Possible ways of accessing the function:
read = read access via function code 03, 04 or 23
write = write access via function code 06, 16 or 23
!Note!
If a nonvolatile device parameter is modified via the MODBUS RS485 function codes 06, 16 or 23,
this change is saved in the EEPROM of the measuring device. The number of writes to the EEPROM
is technically restricted to a maximum of 1 million. Attention must be paid to this limit since, if
exceeded, it results in data loss and measuring device failure. For this reason, avoid constantly
writing nonvolatile device parameters via the MODBUS RS485!
2.3 Display lines on the local display
The local display is split into various display lines.
A0001253
Fig. 4 : Local display
1 Main line
2 Additional line
3Informationline
The values are assigned to the individual lines in the USER INTERFACE block, see Page 33.
UNIT LENGTH
MODBUS register:
Data type:
Access:
0424
2125
Integer
read/write
For selecting the unit for displaying the length of the nominal diameter.
The unit zou select here is also valid for:
- Nominal diameter of sensor, see Function NOMINAL DIAMETER (6804).
Options:
Factory setting:
0 = MILLIMETER
1 = INCH
MILLIMETER
1 2
3
5
64
Esc
E
+
-
1
2
3

Device Functions Proline Promass 83 MODBUS RS485 2 Function Matrix
Endress+Hauser 9
2.4 Function matrix Proline Promass 83
Blocks Groups Function groups
MEASURED VARIABLES
(see P. 10)
A→MEASURING VALUES AAA →see Page 11
SYSTEM UNITS ACA →see Page 15
↓↑
QUICK SETUP
(see P. 20)
B→Commissioning and application setups →see Page 20
↓↑
USER INTERFACE
(see P. 32)
C→CONTROL CAA →see Page 33
MAIN LINE CCA →see Page 37
↓↑
ADDITIONAL LINE CEA →see Page 41
INFORMATION LINE CGA →see Page 47
TOTALIZER
(see P. 53)
D→TOTALIZER 1 DAA →see Page 54
TOTALIZER 2 DAB →see Page 54
↓↑
TOTALIZER 3 DAC →see Page 54
HANDLING TOTALIZER DJA →see Page 57
OUTPUTS
(see P. 58)
E→CURRENT OUTPUT 1 EAA →see Page 59
PULSE/FREQ. OUTPUT 1 ECA →see Page 68
↓↑
RELAY OUTPUT 1 EGA →see Page 93
RELAY OUTPUT 2 EGB →see Page 93
INPUTS
(see P. 102)
F→STATUS INPUT FAA →see Page 103
↓↑
BASIC FUNCTION
(see P. 106)
G→MODBUS RS485 GDA →see Page 107
PROCESS PARAMETER GIA →see Page 109
↓↑
SYSTEM PARAMETER GLA →see Page 118
SENSOR DATA GNA →see Page 119
SPECIAL FUNCTION
(see P. 123)
H→DENSITY FUNCTIONS HAA →see Page 125
BATCHING FUNCTION HCA →see Page 131
↓↑ ADVANCED DIAGNOSTICS HEA →see Page 149
SUPERVISION
(see P. 167)
J→SYSTEM JAA →see Page 168
VERSION INFO JCA →see Page 171

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485
10 Endress+Hauser
3BlockMEASUREDVARIABLES
Functions
CORR. CARR.
VOLUME FLOW
(0029) P. 13
% CARRIER
VOLUME FLOW
(0028) P. 13
CARRIER
VOLUME FLOW
(0027) P. 13
PRESSURE
(0009) P. 11
% CARRIER MASS
FLOW
(0026) P. 13
TEMPERATURE
(0008) P. 11
CARRIER MASS
FLOW
(0025) P. 13
°BRIX
(0036) P. 14
UNIT CORR.
VOLUME
(0405) P. 17
REFERENCE
DENSITY
CORR. TARGET
VOL. FLOW
(0024) P. 12
°BALLING
(0035) P. 14
UNIT CORR. VOL.
FLOW
(0404) P. 17
UNIT
PRESSURE
(0426) P. 19
DENSITY
(0005) P. 11
% TARGET
VOLUME FLOW
(0023) P. 12
°PLATO
(0034) P. 14
UNIT VOLUME
(0403) P. 16
UNIT
LENGTH
(0424) P. 19
CORRECTED
VOLUME FLOW
(0004) P. 11
TARGET VOLUME
FLOW
(0022) P. 12
°API
(0033) P. 14
UNIT VOLUME
FLOW
(0402) P. 16
UNIT
TEMPERATURE
(0422) P. 18
VOLUME FLOW
(0001) P. 11
% TARGET MASS
FLOW
(0021) P. 12
°BAUME
(0031) P. 14
UNIT MASS
(0401) P. 15
UNIT REF.
DENSITY
(0421) P. 18
⇒ ⇒ ⇒ ⇒ ⇒
MASS FLOW
(0000) P. 11
TARGET MASS
FLOW
(0020) P. 12
% BLACK-LIQUOR
(0030) P. 14
UNIT MASS FLOW
(0400) P. 15
UNIT
DENSITY
(0420) P. 18
⇒ ⇒ ⇒ ⇒
Function
groups
MAIN VALUES
(000) P. 11
⇐
⇒
ADDITIONAL
VALUES
CONFIGURATION
(040) P. 15
⇐
⇒
ADDITIONAL
CONFIGURATION
(042) P. 18
⇒ ⇒
Groups
MEASURING
VALUES
⇐
⇒
⇐
⇒
SYSTEM UNITS
(ACA) P. 15
⇒
Block
MEASURED
VARIABLES
(A)

Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES
Endress+Hauser 11
3.1 Group MEASURING VALUES
3.1.1 Function group MAIN VALUES
MEASURED
VARIABLES
A→MEASURING VALUES AAA →MAIN VALUES 000
Function description
MEASURED VARIABLES →MEASURING VALUES →MAIN VALUES
!Note!
• The engineering units of all the measured variables shown here can be set in the “SYSTEM UNITS” group.
• If the fluid in the pipe flows backwards, a negative sign prefixes the flow reading on the display.
MASS FLOW
MODBUS register:
Data type:
Access:
0000
2007
247
Float
read
The currently measured mass flow appears on the display.
Display: 5-digit floating-point number, including unit and sign
(e.g. 462.87 kg/h; -731.63 lb/min; etc.)
VOLUME FLOW
MODBUS register:
Data type:
Access:
0001
2009
253
Float
read
The calculated volume flow appears on the display. The volume flow is derived
from the measured mass flow and the measured density of the fluid.
Display: 5-digit floating-point number, including unit and sign
(e.g. 5.5445 dm3/min; 1.4359 m3/h; -731.63 gal/d; etc.)
CORRECTED
VOLUME FLOW
MODBUS register:
Data type:
Access:
0004
2011
Float
read
The calculated corrected volume flow appears on the display. The calculated
corrected volume flow is derived from the measured mass flow and the reference
density of the fluid (density at reference temperature, measured or fixed entry).
Display: 5-digit floating-point number, including unit and sign
(e.g. 1.3549 Nm3/h; 7.9846 scm/day; etc.)
DENSITY
MODBUS register:
Data type:
Access:
0005
2013
249
Float
read
The currently measured density or its specific gravity appears on the display.
Display: 5-digit floating point number, incl. unit,
corresponding to 0.1000 to 6.0000 kg/dm3
(e.g. 1.2345 kg/dm3; 993.5 kg/m3; 1.0015 SG_20 °C; etc.)
REFERENCE
DENSITY
MODBUS register:
Data type:
Access:
0006
2015
Float
read
The density of the fluid, at reference temperature, appears on the display. The
reference density can be measured or also specified via the function FIXED
REFERENCE DENSITY (6461), (see Page 113).
Display: 5-digit floating point number, incl. unit,
corresponding to 0.1000 to 6.0000 kg/dm3
(e.g. 1.2345 kg/dm3; 993.5 kg/m3; 1.0015 SG_20 °C; etc.)
TEMPERATURE
MODBUS register:
Data type:
Access:
0008
2017
251
Float
read
The currently measured temperature appears on the display.
Display: max. 4-digit fixed-point number, including unit and sign
(e.g. -23.4 °C; 160.0 °F; 295.4 K; etc.)
PRESSURE
MODBUS register:
Data type:
Access:
0009
2089
257
Float
read
The specified pressure appears on the display.
Display: max. 4-digit fixed-point number, including unit and sign
(e.g. 50 barg, etc.)

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485
12 Endress+Hauser
3.1.2 Function group ADDITIONAL VALUES
MEASURED
VARIABLES A→MEASURING VALUES AAA →MAIN VALUES 000
→
ADDITIONAL VALUES 002
Function description
MEASURED VARIABLES →MEASURING VALUES →ADDITIONAL VALUES
TARGET MASS
FLOW
MODBUS register:
Data type:
Access:
0020
2023
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
MASS 2D or % MASS 3D
The currently measured mass flow of the target fluid appears on the display.
Target fluid = carried material (e.g. lime powder).
Display: 5-digit floating-point number, including unit and sign
% TARGET MASS
FLOW
MODBUS register:
Data type:
Access:
0021
2025
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
MASS 2D or % MASS 3D
The currently measured mass flow of the target fluid is displayed as a % (of the
overall mass flow). Target fluid = carried material (e.g. lime powder).
Display: 5-digit floating-point number, including unit and sign
TARGET VOLUME
FLOW
MODBUS register:
Data type:
Access:
0022
2029
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
VOLUME 2D or % VOLUME 3D
The currently measured volume flow of the target fluid appears on the display.
Target fluid = carried material (e.g. lime powder).
Display: 5-digit floating-point number, including unit and sign
% TARGET
VOLUME FLOW
MODBUS register:
Data type:
Access:
0023
2031
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
VOLUME 2D or % VOLUME 3D
The currently measured volume flow of the target fluid is displayed as a % (of the
overall volume flow). Target fluid = carried material (e.g. lime powder).
Display: 5-digit floating-point number, including unit and sign
CORRECTED
TARGET VOLUME
FLOW
MODBUS register:
Data type:
Access:
0024
2033
Float
read
!Note!
Function is not available unless % MASS / % VOLUME was selected in the
DENSITY FUNCTION function (7000), (see Page 125).
The currently measured corrected volume flow of the target fluid appears on the
display.
Target fluid = carried material (e.g. lime powder).
Display: 5-digit floating-point number, including unit and sign

Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES
Endress+Hauser 13
CARRIER MASS
FLOW
MODBUS register:
Data type:
Access:
0025
2035
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
MASS 2D or % MASS 3D
The currently measured mass flow of the carrier fluid appears on the display.
Carrier fluid = transporting liquid (e.g. water).
Display: 5-digit floating-point number, including unit and sign
% CARRIER MASS
FLOW
MODBUS register:
Data type:
Access:
0026
2037
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
MASS 2D or % MASS 3D
The currently measured mass flow of the carrier fluid is displayed as a % (of the
overall mass flow). Carrier fluid = transporting liquid (e.g. water).
Display: 5-digit floating-point number, including unit and sign
CARRIER VOLUME
FLOW
MODBUS register:
Data type:
Access:
0027
2039
Float
read
!Note!
Function is not available unless one of the following was selected:
• in the function DENSITY FUNCTION (7000), see Page 125:
– % MASS / % VOLUME
– FLEXIBLE and in the function MODE (7021), see Page 127, the selection %
VOLUME 2D or % VOLUME 3D
The currently measured volume flow of the carrier fluid appears on the display.
Carrier fluid = transporting liquid (e.g. water).
Display: 5-digit floating-point number, including unit and sign
% CARRIER
VOLUME FLOW
MODBUS register:
Data type:
Access:
0028
2041
Float
read
!Note!
Function is not available unless % MASS / % VOLUME was selected in the
DENSITY FUNCTION function (7000), (see Page 125).
Use this function to display the currently measured corrected volume flow of the
carrier fluid. Carrier fluid = transporting liquid (e.g. water).
Display: 5-digit floating-point number, including unit and sign
CORRECTED
CARRIER VOLUME
FLOW
MODBUS register:
Data type:
Access:
0029
2043
Float
read
!Note!
Function is not available unless % MASS / % VOLUME was selected in the
DENSITY FUNCTION function (7000), (see Page 125).
The currently measured corrected volume flow of the carrier fluid appears on the
display.
Carrier fluid = transporting liquid (e.g. water).
Display: 5-digit floating-point number, including unit and sign
Function description
MEASURED VARIABLES →MEASURING VALUES →ADDITIONAL VALUES

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485
14 Endress+Hauser
% BLACK-LIQUOR
MODBUS register:
Data type:
Access:
0030
2027
Float
read
!Note!
Function is not available unless %-BLACK LIQUOR was selected in the DENSITY
FUNCTION function (7000), (see Page 125).
The concentration in %-BLACK LIQUOR is displayed.
Display: 5-digit floating-point number, including units
°BAUME
MODBUS register:
Data type:
Access:
0031
2045
Float
read
!Note!
Function is not available unless °BAUME was selected in the DENSITY
FUNCTION function (7000), (see Page 125).
The concentration in °BAUME is displayed.
Display: 5-digit floating-point number, including units
°API
MODBUS register:
Data type:
Access:
0033
2049
Float
read
!Note!
Function is not available unless °API was selected in the DENSITY FUNCTION
function (7000), (see Page 125).
The concentration in °API is displayed.
Display: 5-digit floating-point number, including units
°PLATO
MODBUS register:
Data type:
Access:
0034
2051
Float
read
!Note!
Function is not available unless °PLATO was selected in the DENSITY
FUNCTION function (7000), (see Page 125).
The concentration in °PLATO is displayed.
Display: 5-digit floating-point number, including units
°BALLING
MODBUS register:
Data type:
Access:
0035
2053
Float
read
!Note!
Function is not available unless °BALLING was selected in the DENSITY
FUNCTION function (7000), (see Page 125).
The concentration in °BALLING is displayed.
Display: 5-digit floating-point number, including units
°BRIX
MODBUS register:
Data type:
Access:
0036
2055
Float
read
!Note!
Function is not available unless °BRIX was selected in the DENSITY FUNCTION
function (7000), (see Page 125).
The concentration in °BRIX is displayed.
Display: 5-digit floating-point number, including units
Function description
MEASURED VARIABLES →MEASURING VALUES →ADDITIONAL VALUES

Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES
Endress+Hauser 15
3.2 Group SYSTEM UNITS
3.2.1 Function group CONFIGURATION
MEASURED
VARIABLES A→MEASURING VALUES AAA
→
SYSTEM UNITS ACA →CONFIGURATION 040
Function description
MEASURED VARIABLES →SYSTEM UNITS →CONFIGURATION
You can select the units for measured variables in this function group.
UNIT MASS FLOW
MODBUS register:
Data type:
Access:
0400
2101
Integer
read/write
For selecting the unit for displaying the mass flow (mass/time).
The unit you select here is also valid for:
• Current output
• Frequency output
• Relay switch points (limit value for mass flow, flow direction)
• Low flow cut off
Options:
Metric:
0 to 3 = gram →g/s; g/min; g/h; g/day
4 to 7 = kilogram →kg/s; kg/min; kg/h; kg/day
8 to 11 = ton →t/s; t/min; t/h; t/day
US:
12 to 15 = ounce →oz/s; oz/min; oz/h; oz/day
16 to 19 = pound →lb/s; lb/min; lb/h; lb/day
20 to 23 = ton →ton/s; ton/min; ton/h; ton/day
Factory setting: Country-dependent (kg/h or US-lb/min)
UNIT MASS
MODBUS register:
Data type:
Access:
0401
2102
Integer
read/write
For selecting the unit for displaying the mass.
The unit you select here is also valid for:
• Pulse value (e.g. kg/p)
Options:
Metric:
0 = g
1 = kg
2 = t
US:
3 = oz
4 = lb
5 = ton
Factory setting: Country-dependent (kg or US-lb)
!Note!
The unit of the totalizers is independent of your choice here. The unit for each
totalizer is selected separately for the totalizer in question.

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485
16 Endress+Hauser
UNIT VOLUME
FLOW
MODBUS register:
Data type:
Access:
0402
2103
Integer
read/write
For selecting the unit for displaying the volume flow (volume/time).
The unit you select here is also valid for:
• Current output
• Frequency output
• Relay switch points (limit value for volume flow, flow direction)
• Low flow cut off
Options:
Metric:
0 to 3 = cubic centimeter →cm3/s; cm3/min; cm3/h; cm3/day
4 to 7 = cubic decimeter →dm3/s; dm3/min; dm3/h; dm3/day
8 to 11 = cubic meter →m3/s; m3/min; m3/h; m3/day
12 to 15 = milliliter →ml/s; ml/min; ml/h; ml/day
16 to 19 = liter →l/s; l/min; l/h; l/day
20 to 23 = hectoliter →hl/s; hl/min; hl/h; hl/day
24 to 27 = megaliter →Ml/s; Ml/min; Ml/h; Ml/day
US:
28 to 31 = cubic centimeter →cc/s; cc/min; cc/h; cc/day
32 to 35 = acre foot →af/s; af/min; af/h; af/day
36 to 39 = cubic foot →ft3/s; ft3/min; ft3/h; ft3/day
40 to 43 = fluid ounce →oz f/s; oz f/min; oz f/h; oz f/day
44 to 47 = gallon →gal/s; gal/min; gal/h; gal/day
88 to 92 = kilo gallon →Kgal/s; Kgal/min; Kgal/h; Kgal/day
48 to 51 = million gallon →Mgal/s; Mgal/min; Mgal/h; Mgal/day
52 to 55 = barrel (normal fluids: 31.5 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
56 to 59 = barrel (beer: 31.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
60 to 63 = barrel (petrochemicals: 42.0 gal/bbl) →bbl/s; bbl/min; bbl/h;
bbl/day
64 to 67 = barrel (filling tanks: 55.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Imperial:
68 to 71 = gallon →gal/s; gal/min; gal/h; gal/day
72 to 75 = mega gallon →Mgal/s; Mgal/min; Mgal/h; Mgal/day
76 to 79 = barrel (beer: 36.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
80 to 83 = barrel (petrochemicals: 34.97 gal/bbl) →bbl/s; bbl/min; bbl/h;
bbl/day
Factory setting: Country-dependent (m3/h or US-Mgal/day)
UNIT VOLUME
MODBUS register:
Data type:
Access:
0403
2104
Integer
read/write
For selecting the unit for displaying the volume.
The unit you select here is also valid for: Pulse weighting (e.g. m3/p)
Options:
0 to 6 = metric →cm3; dm3; m3; ml; l; hl; Ml Mega
7 to 16 = US →cc; af; ft3; oz f; gal; Mgal; bbl (normal fluids); bbl (beer);
bbl (petrochemicals); bbl (filling tanks);
22 = Kgal
17 to 20 = Imperial →gal; Mgal; bbl (beer); bbl (petrochemicals)
Factory setting: m3
!Note!
The unit of the totalizers is independent of your choice here. The unit for each
totalizer is selected separately for the totalizer in question.
Function description
MEASURED VARIABLES →SYSTEM UNITS →CONFIGURATION

Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES
Endress+Hauser 17
UNIT CORRECTED
VOLUME FLOW
MODBUS register:
Data type:
Access:
0404
2105
Integer
read/write
For selecting the unit for displaying the corrected volume flow (corrected
volume/time).
The unit you select here is also valid for:
• Current output
• Frequency output
• Relay switch points (limit value for corrected volume flow, flow direction)
• Low flow cut off
Options:
Metric:
0 = Nl/s
1 = Nl/min
2 = Nl/h
3 = Nl/day
4 = Nm3/s
5 = Nm3/min
6 = Nm3/h
7 = Nm3/day
US:
8 = Sm3/s
9 = Sm3/min
10 = Sm3/h
11 = Sm3/day
12 = Scf/s
13 = Scf/min
14 = Scf/h
15 = Scf/day
Factory setting: Nm3/h
UNIT CORRECTED
VOLUME
MODBUS register:
Data type:
Access:
0405
2106
Integer
read/write
For selecting the unit for displaying the corrected volume.
The unit you select here is also valid for:
• Pulse value (e.g. Nm3/p)
Options:
Metric:
0 = Nm3
1 = Nl
US:
2 = Sm3
3 = Scf
Factory setting: Nm3
!Note!
The unit of the totalizers is independent of your choice here. The unit for each
totalizer is selected separately for the totalizer in question.
Function description
MEASURED VARIABLES →SYSTEM UNITS →CONFIGURATION

3 Block MEASURED VARIABLES Device Functions Proline Promass 83 MODBUS RS485
18 Endress+Hauser
3.2.2 Function group ADDITIONAL CONFIGURATION
MEASURED
VARIABLES A→MEASURING VALUES AAA
→
SYSTEM UNITS ACA →CONFIGURATION 040
→
ADDITIONAL
CONFIGURATION
042
Function description
MEASURED VARIABLES →SYSTEM UNITS →ADDITIONAL CONFIGURATION
UNIT DENSITY
MODBUS register:
Data type:
Access:
0420
2107
Integer
read/write
For selecting the unit for displaying the fluid density.
The unit you select here is also valid for:
• Current output
• Frequency output
• Relay switch points (limit value for density)
• Density response value for EPD
•Densityadjustmentvalue
Options:
0 to 10 = metric →g/cm3; g/cc; kg/dm3; kg/l; kg/m3; SD 4 °C, SD 15 °C, SD
20 °C; SG 4 °C, SG 15 °C, SG 20 °C
11 to 16 = US →lb/ft3; lb/gal; lb/bbl (normal fluids); lb/bbl (beer);
lb/bbl (petrochemicals); lb/bbl (filling tanks)
17 to 19 = Imperial →lb/gal; lb/bbl (beer); lb/bbl (petrochemicals)
Factory setting: kg/l
SD = Specific Density, SG = Specific Gravity
The specific density is the ratio of fluid density to water density (at water
temperature = 4, 15, 20 °C).
UNIT REFERENCE
DENSITY
MODBUS register:
Data type:
Access:
0421
2108
Integer
read/write
For selecting the unit for displaying the reference density.
The unit you select here is also valid for:
• Current output
• Frequency output
• Relay switch points (limit value for density)
• Fixed reference density (for calculation of corrected volume flow)
Options:
Metric:
1 = kg/Nl
2 = kg/Nm3
US:
0 = g/Scc
3 = kg/Sm3
4 = lb/Scf
Factory setting: kg/Nl
UNIT
TEMPERATURE
MODBUS register:
Data type:
Access:
0422
2109
Integer
read/write
For selecting the unit for displaying the temperature.
The unit you select here is also valid for:
• Current output
• Frequency output
• Relay switch points (limit value for temperature)
• Reference temperature (for corrected vol. measurement with measured
reference density)
Options:
0 = °C (Celsius)
1 = K (Kelvin)
2 = °F (Fahrenheit)
3 = °R (Rankine)
Factory setting: °C

Device Functions Proline Promass 83 MODBUS RS485 3 Block MEASURED VARIABLES
Endress+Hauser 19
UNIT LENGTH
MODBUS register:
Data type:
Access:
0424
2125
Integer
read/write
For selecting the unit for displaying the length of the nominal diameter.
The unit you select here is also valid for:
• Nominal diameter of sensor (function NOMINAL DIAMETER (6804) on
Page 119)
Options:
0 = MILLIMETER
1 = INCH
Factory setting: MILLIMETER
UNIT PRESSURE
MODBUS register:
Data type:
Access:
0426
2130
Integer
read/write
For selecting the unit for displaying the pressure.
The unit you select here is also valid for:
• Specified pressure (function PRESSURE (6501) on Page 117)
Options:
0 = bara
1 = barg
2 = psia
3 = psig
Factory setting: barg
Function description
MEASURED VARIABLES →SYSTEM UNITS →ADDITIONAL CONFIGURATION

4 Block QUICK SETUP Device Functions Proline Promass 83 MODBUS RS485
20 Endress+Hauser
4BlockQUICKSETUP
Block Group /
Function groups Functions
QUICK SETUP
(B) ⇒
QS
COMMISSION
(1002) P. 20
⇒
QS - PULS.
FLOW
(1003) P. 20
QS -
BATCHING
(1005) P. 20
SETUP
GAS MEAS.
(1004) P. 20
QS - COM-
MUNICATION
(1006) P. 20
T-DAT
SAVE/LOAD
(1009) P. 21
Function description
QUICK SETUP
!Note!
• The Quick Setups are only available by means of the local display.
• The flowcharts of the various Quick Setups are provided on the pages to follow.
• For more information on the Setup menus, please refer to the Operating Instructions BA107D.
QUICK SETUP
COMMISSION
1002 For starting the Setup menu.
Options:
NO
YES
Factory setting: NO
QUICK SETUP
PULSATING FLOW
1003 !Note!
Function only available for measuring devices with a current or frequency output.
For starting the Setup menu.
Options:
NO
YES
Factory setting: NO
QUICK SETUP
BATCHING/
DOSING
1005 !Note!
Function is only available with the optional software package BATCHING.
For starting the Setup menu.
Options:
NO
YES
Factory setting: NO
SETUP GAS
MEASUREMENT
1004 For starting the Setup menu.
Options:
NO
YES
Factory setting: NO
QUICK SETUP
COMMUNICATION
1006 For starting the Setup menu.
Options:
NO
YES
Factory setting: NO