Endress+Hauser Deltabar S PMD75 Manual

TI00382P/00/EN/19.14
No. 71254471
Technical Information
Deltabar S PMD70/75, FMD76/77/78
Differential pressure measurement
Differential pressure transmitter with ceramic and silicon sensors
Overload-resistant and function-monitored; Communication via
HART, PROFIBUS PA or FOUNDATION Fieldbus
Application
The Deltabar S differential pressure transmitter is used
for the following measuring tasks:
• Flow measurement (volume or mass flow) in
conjunction with primary devices in gases, vapors and
liquids
• Level, volume or mass measurement in liquids
• Differential pressure monitoring, e.g. of filters and
pumps
• International usage thanks to a wide range of approvals
Your benefits
• Very good reproducibility and long-term stability
• High reference accuracy: up to r0.075 %,
as PLATINUM version: r0.05 %
• Turn down up to 100:1, higher on request
• Used for flow and differential pressure monitoring
up to SIL 3, certified to IEC 61508 by TÜV SÜD
• HistoROM®/M-DAT memory module
• Function-monitored from the measuring cell to the
electronics
• Continuous modularity for differential pressure,
hydrostatics and pressure (Deltabar S, Deltapilot S,
Cerabar S), e.g.
– replaceable display
– universal electronics
• Quick commissioning with Quick Setup menu
• Menu-guided operation
• Extensive diagnostic functions
• New TempC diaphragm for diaphragm seals:
Minimum temperature effects and short recovery
times

Deltabar S
2Endress+Hauser
Table of contents
Function and system design. . . . . . . . . . . . . . . . . . . . . 4
Device selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Flow measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Level measurement (level, volume and mass) . . . . . . . . . . . . . . . . 7
Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Explanation of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal range – 4 to 20 mA HART . . . . . . . . . . . . . . . . . . . . . . . . 10
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Load – 4 to 20 mA HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dead time, time constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dynamic behavior: current output . . . . . . . . . . . . . . . . . . . . . . . 11
Dynamic behavior: digital output (HART electronics) . . . . . . . . . 11
Dynamic behavior: PROFIBUS PA . . . . . . . . . . . . . . . . . . . . . . . . 12
Dynamic behavior: FOUNDATION Fieldbus . . . . . . . . . . . . . . . . 13
Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Protocol-specific data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Residual ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Influence of power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Performance characteristics – general . . . . . . . . . . . . 22
Reference operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Influence of the installation position . . . . . . . . . . . . . . . . . . . . . . 22
Vibration effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Performance characteristics – metal process isolating
diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Reference accuracy – PMD75, FMD77, FMD78 . . . . . . . . . . . . . 23
Thermal change of the zero output and the output span –
PMD75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Influence of the operating pressure on zero point and span – PMD75,
FMD77, FMD78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Total performance – PMD75 . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Long-term stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Total error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Warm-up period – PMD75, FMD77, FMD78 . . . . . . . . . . . . . . . 25
Performance characteristics – ceramic process isolating
diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Reference accuracy – PMD70, FMD76 . . . . . . . . . . . . . . . . . . . 26
Thermal change of the zero output and the output span – PMD70,
FMD76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Influence of the operating pressure on zero point and span –
PMD70, FMD76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Total performance – PMD70, FMD76 . . . . . . . . . . . . . . . . . . . . 26
Long-term stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Total error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Warm-up period – PMD70, FMD76 . . . . . . . . . . . . . . . . . . . . . 27
Operating conditions (Installation) . . . . . . . . . . . . . . 28
General installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . 28
Measuring arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Wall and pipe-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
"Separate housing" version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Turning the housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Oxygen applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ultrapure gas applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Applications with hydrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Operating conditions (Environment) . . . . . . . . . . . . . 33
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Overvoltage protection (optional) . . . . . . . . . . . . . . . . . . . . . . . . 33
Operating conditions (Process) . . . . . . . . . . . . . . . . . 34
Process temperature limits (temperature at transmitter) . . . . . . . 34
Process temperature range, seals . . . . . . . . . . . . . . . . . . . . . . . . 34
Pressure specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Mechanical construction . . . . . . . . . . . . . . . . . . . . . . 36
Dimensions of T14 housing, optional display on the side . . . . . . . 36
Dimensions of T15 housing, optional display on the top . . . . . . . 36
Dimensions of T17 housing (hygienic), optional display on
the side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Process connections PMD70 with ceramic process isolating
diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Process connections PMD70 with ceramic process isolating
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Process connections PMD75 with metal process isolating
diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Process connections PMD75 with metal process isolating
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Process connections PMD75 with metal process isolating
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Process connection FMD76 with ceramic process isolating
diaphragms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Process connection FMD76 with ceramic process isolating
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Process connection FMD76 with ceramic process isolating
diaphragms (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Process connections FMD77 with diaphragm seal,
low-pressure side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Process connections FMD77 with diaphragm seal,
high-pressure side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Process connections FMD77 with diaphragm seal,
high-pressure side (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . 47

3Endress+Hauser
Deltabar S
Process connections FMD77 with diaphragm seal,
high-pressure side (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Process connections FMD77 with diaphragm seal,
high-pressure side (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . 49
FMD78 basic device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Process connections FMD78 with diaphragm seal . . . . . . . . . . . . 51
Process connections FMD78 with diaphragm seal (continued) . . 52
Process connections FMD78 with diaphragm seal (continued) . . 53
Process connections FMD78 with diaphragm seal (continued) . . 55
Process connections FMD78 with diaphragm seal (continued) . . 57
Process connections FMD78 with diaphragm seal (continued) . . 58
Process connections FMD78 with diaphragm seal (continued) . . 59
Wall and pipe mounting with mounting bracket or separate
housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Material (not wetted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Material (wetted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Filling oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Hardware and software for onsite and remote operation . . . . . . . 69
Planning instructions, diaphragm seal systems . . . . . 71
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Design and operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Diaphragm seal filling oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Operating temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Response time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Cleaning instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Certificates and approvals . . . . . . . . . . . . . . . . . . . . . 77
CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Ex approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Suitability for hygienic processes . . . . . . . . . . . . . . . . . . . . . . . . 77
Marine certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Functional Safety SIL / IEC 61508 Declaration of Conformity
(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Overfill prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
CRN approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Pressure Equipment Directive (PED) . . . . . . . . . . . . . . . . . . . . . 77
Standards and guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Classification of process sealing between electrical systems and
(flammable or combustible) process fluids in accordance with ANSI/
ISA 12.27.01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . 79
PMD70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
PMD70 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
PMD70 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
PMD75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
PMD75 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
PMD75 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
FMD76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
FMD76 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
FMD76 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
FMD77 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
FMD77 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
FMD77 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
FMD78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
FMD78 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
FMD78 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
FMD78 (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Additional documentation . . . . . . . . . . . . . . . . . . . . . 95
Field of Activities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Brief Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Functional safety manual (SIL) . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Installation/Control Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Overfill prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Configuration data sheet . . . . . . . . . . . . . . . . . . . . . . 97
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Registered trademarks. . . . . . . . . . . . . . . . . . . . . . . 100
HART® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
PROFIBUS® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
FOUNDATION™ Fieldbus . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Deltabar S
4Endress+Hauser
Function and system design
Device selection
Deltabar S –
product family
PMD70 PMD75 FMD76 FMD77 FMD78
P01-PMD70xxx-16-xx-xx-xx-000
With ceramic process
isolating diaphragms
P01-PMD75xxx-16-xx-xx-xx-000
With metal process
isolating diaphragms
P01-FMD76xxx-16-xx-xx-xx-000
With ceramic process
isolating diaphragms
P01-FMD77xxx-16-xx-xx-xx-000
With metal process
isolating diaphragms
and diaphragm seal
mounted on one side
P01-FMD78xxx-16-xx-xx-xx-003
With metal process
isolating diaphragms
and capillary
diaphragm seals
Field of application – Flow
– Level
– Differential pressure
–Flow
– Level
– Differential pressure
– Level – Level – Level
– Differential pressure
Process connections – 1/4 – 18 NPT
–RC1/4
–1/4–18NPT
–RC1/4
Low-pressure side (–):
–1/4–18NPT
–RC1/4
High-pressure side (+):
– DN 80 – DN 100
–ANSI3"–4"
– JIS 80A – 100A
Low-pressure side (–):
–1/4–18NPT
–RC1/4
High-pressure side (+):
– DN 50 – DN 100
–ANSI2"–4"
– JIS 80A – 100A
– Wide range of
diaphragm seals
Measuring ranges From –25 to +25 mbar
(-0.375 to +0.375 psi)
to –3 to +3 bar
(-45 to +45 psi)
From –10 to +10 mbar
(-0.15 to +0.15 psi)
to –40 to +40 bar
(-600 to +600 psi)
From –100 to +100
mbar (-1.5 to +1.5 psi)
to –3 to +3 bar
(-45 to +45 psi)
From –100 to +100 mbar
(-1.5 to +1.5 psi)
to –16 bar to +16 bar
(-240 to +240 psi)
From –100 to +100 mbar
(-1.5 to +1.5 psi)
to –40 to +40 bar
(-600 to +600 psi)
OPL 1) On one side: up to
100 bar (1500 psi)
On both sides: up to
150 bar (2250 psi)
On one side: up to
420 bar (6300 psi)
On both sides: up to
630 bar (9450 psi)
On one side: up to
100 bar (1500 psi)
On one side: up to
160 bar (2400 psi)
On both sides: up to
240 bar (3600 psi)
On one side: up to
160 bar (2400 psi)
On both sides: up to
240 bar (3600 psi)
Process temperature
range (temperature at
process connection)
–20 to +85°C
(–4 to +185°F)
–40 to +85°C
(–40 to +185°F)
–20 to +85°C
(–4 to +185°F)
Up to +400 °C (752 °F)
(depending on the filling
oil)
Up to +400 °C (752 °F)
(depending on the filling
oil)
Ambient temperature
range
–20 to +85 °C
(-4 to +185 °F)
–40 to +85°C
(–40 to +185°F) 2)
–20 to +85°C
(-4 to +185 °F)
–40 to +85 °C
(-40 to +185 °F) 2)
–40 to +85 °C
(-40 to +185 °F)2)
Ambient temperature
range, separate housing
-20 to +60°C
(-4 to +122 °F)
Reference accuracy – Up to r0.075 % of the set span
– PLATINUM version: up to r0.05 % of the set span
–Uptor0.075 % of the set span
Supply voltage – Version for non-hazardous areas:
– 4...20 mA HART: 10.5 to 45 V DC
– PROFIBUS PA and FOUNDATION Fieldbus: 9 to 32 V DC
– Ex ia: 10.5 to 30 V DC
Output 4 to 20 mA with superimposed HART protocol, PROFIBUS PA or FOUNDATION Fieldbus
Options – High-pressure version up to pstat 700 bar (10500 psi)
– PMD75, FMD77, FMD78: gold-rhodium-coated process isolating diaphragm, NACE-compliant material
– Separate housing
+ –
+ –

Deltabar S
Endress+Hauser 5
Measuring principle
Ceramic process isolating diaphragm used for PMD70 and FMD76
The ceramic measuring cell is based on the principle of a plate capacitor with an electrode on a meter body (1)
and a movable electrode on the interior of the diaphragm (3). Silicone oil or mineral oil are used as the standard
filling oils for this measuring cell.
A differential pressure (p1 zp2) causes a corresponding deflection of both diaphragms. Both capacitance values
are converted and are fed to the microprocessor of the transmitter as a digital signal.
Advantages:
• Self-monitoring for process isolating diaphragm break or oil loss (constant comparison of the measured
temperature with a temperature calculated from the capacitance values)
• Extremely high resistance to aggressive media
• Suitable for vacuums up to 1 mbarabs (0.015 psi)
• Metal-free versions available
• Secondary containment for enhanced integrity
Metal process isolating diaphragm used for PMD75, FMD77 and FMD78
The process isolating diaphragms (3/9) are deflected on both sides by the acting pressures. A filling oil (4/8)
transfers the pressure to a resistance bridge (semi-conductor technology). The change in the bridge output
voltage, which depends on the differential pressure, is measured and processed further.
Advantages:
• Standard system pressures: 160 bar (2400 psi) and 420 bar (6300 psi)
• High long-term stability
• Very high single-sided overload resistance
Specialties
(options)
– Metal-free
measurement with
PVDF flange
– Available with
Deltatop as flow
compact device
–p
stat to 420 bar
(6300 psi)
– Process isolating
diaphragm: tantalum
– Available with
Deltatop as flow
compact device
– Abrasion-resistant and
corrosion-resistant
– No diaphragm-seal
temperature effects
– Metal-free
measurement possible
with ECTFE-coated
process connection
–Forhighmedia
temperatures
– Wide range of
diaphragm seals
–HistoROM
®/M-DAT memory module
1) OPL: over pressure limit; dependent on the lowest-rated element, with regard to pressure, of the selected components
2) Lower temperatures on request
Deltabar S –
product family
PMD70 PMD75 FMD76 FMD77 FMD78
Ceramic process isolating diaphragm used for
PMD70 and FMD76
Metal process isolating diaphragm used for PMD75,
FMD77 and FMD78
P01-xMD7xxxx-03-xx-xx-xx-000
1 Meter body
2 Process isolating diaphragm
3Electrodes
4 Glass frit fixes the process isolating diaphragm
onto the meter body
5Temperaturesensor
P01-xMD7xxxx-03-xx-xx-xx-003
6 Sensing element
7 Middle diaphragm
8 Filling oil
9 Process isolating diaphragm
➀
➁
➃
➂
➄
1
p2
p
1
p2 p
➆
➇
➈
➅

Deltabar S
6Endress+Hauser
Flow measurement Design and operation mode
P01-PMD7xxxx-15-xx-xx-xx-000
Flow measurement with Deltabar S and primary device, left: orifice plate and right: Pitot tube
QFlow
'p Differential pressure, 'p = p1– p2
Your benefits
• Choice of four flow modes of operation: volume flow, corrected volume flow (European norm conditions),
standard volume flow (American standard conditions) and mass flow.
• Choice of diverse flow units with automatic unit conversion.
• A customized unit can be specified.
• Low flow cut off: when activated, this function suppresses small flows which can lead to large fluctuations
in the measured value.
• Contains two totalizers as standard. One totalizer can be reset to zero.
• The totalizing mode and unit can be individually set for each totalizer. This allows independent daily and
annual quantity totalizing.
• With the Deltatop product family, Endress+Hauser is offering universal and reliable solutions for flow
measurement:
– Deltatop, the compact, ready-to-use flow measuring unit including the Deltabar S differential pressure
transmitter
Note!
For more information about flow measurement with the Deltabar S differential pressure transmitter
• Deltabar S with orifice plate (TI00422P, Deltatop DO6x)
• Deltabar S with Pitot tube (TI00425P, Deltatop DP6x)
QQ
p
1
p
1
p
2
p
2
Q~ ΔpQ~ Δp
++ ––

Deltabar S
Endress+Hauser 7
Level measurement (level,
volume and mass)
Design and operation mode
P01xMD7xxxx-15-xx-xx-xx-000
Level measurement with Deltabar S
1 Level measurement via pressure piping and PMD70
2 Level measurement with FMD76
3 Level measurement with FMD78
h Height (level)
'p Differential pressure
UDensity of the media
g Gravitation constant
Your benefits
• Choice of three level operating modes.
• Volume and mass measurements in any tank shapes by means of a freely programmable characteristic curve.
• Choice of diverse level units with automatic unit conversion.
• A customized unit can be specified.
• Has a wide range of uses, e.g.
– for level measurement in tanks with pressure overlay
– in the event of foam formation
– in tanks with agitators of screen fittings
– in the event of liquid gases
– for standard level measurement
Communication protocol • 4 to 20 mA with HART communication protocol
• PROFIBUS PA
– The Endress+Hauser devices meet the requirements of the FISCO model.
– Due to the low current consumption of 13 mA ± 1 mA, the following number of devices can be operated
on one bus segment if installing as per FISCO:
– up to 7 Deltabar S for Ex ia, CSA IS and FM IS applications
– up to 27 Deltabar S for all other applications, e.g. in non-hazardous areas, Ex nA, etc.
Further information on PROFIBUS PA can be found in Operating Instructions BA00034S "PROFIBUS DP/
PA: Guidelines for planning and commissioning" and in the PNO Guideline.
• FOUNDATION Fieldbus
– The Endress+Hauser devices meet the requirements of the FISCO model.
– Due to the low current consumption of 15,5 mA ± 1 mA, the following number of devices can be operated
on one bus segment if installing as per FISCO:
– up to 6 Deltabar S for Ex ia, CSA IS and FM IS applications
– up to 24 Deltabar S for all other applications, e.g. in non-hazardous areas, Ex nA, etc.
Further information on FOUNDATION Fieldbus, such as requirements for bus system components can be
found in Operating Instructions BA00013S "FOUNDATION Fieldbus Overview".
h= Δp
ρg
+
+
––
h
➀
➂
➁

Deltabar S
8Endress+Hauser
Input
Measured variable Differential pressure, from which flow (volume flow or mass flow) and level (level, volume or mass) are derived
Measuring range PMD75, FMD77, FMD78 (with metal process isolating diaphragms)
PMD70, FMD76 (with ceramic process isolating diaphragms)
Nominal
value
Range limit Smallest
calibratable
span 5)
MWP 1 OPL
2) Min. operating
pressure 3)
Versions in the order
code 4)
lower (LRL) upper (URL) on one side on both
sides
PN 160 6) PN 420 6)
[mbar (psi)] [mbar (psi)] [mbar (psi)] [mbar (psi)] [bar (psi)] [bar (psi)] [bar (psi)] [mbarabs (psiabs)]
10 (0.15) 7) –10 (-0.15) +10 (+0.15) 0.25 (0.00375) 160 (2400) 160 (2400) 240 (3600)
0.1 (0.0015)
7B –
30 (0.45) 7) –30 (-0.45) +30 (+0.45) 0.3 (0.0045) 7C –
100 (1.5) –100 (-1.5) +100 (+1.5) 1/5
(0.015/0.075) 8)
160 (2400) /
420 (6300) 9)
160 (2400) /
420 (6300)
240/630
(3600/9450)
7D 8D
500 (7.5) –500 (-7.5) +500 (+7.5) 5 (0.075) 7F 8F
3000 (45) –3000 (-45) +3000 (+45) 30 (0.45) 7H 8H
16000 (240) –16000 (-240) +16000 (+240) 160 (2.4) 7L 8L
40000 (600) –40000 (-600) +40000 (+600) 400 (6) "+" side 10):
160 (2400) /
420 (6300) 11)
7M 8M
Nominal
value
Range limit Smallest
calibratable
span 5)
MWP 1) OPL 2) Min. operating
pressure 3)
Versions in the
order code 4)
lower (LRL) upper (URL) on one side on both
sides
[mbar (psi)] [mbar (psi)] [mbar (psi)] [mbar (psi)] [bar (psi)] [bar (psi)] [bar (psi)] [mbarabs (psiabs)]
25 (0.375) –25 (-0.375) +25 (+0.375) 0.25 (0.00375) 10 (150) 10 (150) 15 (225)
1 (0.015)
7B
100 (1.5) –100 (-1.5) +100 (+1.5) 1 (0.015) 16 (240) 16 (240) 24 (360) 7D
500 (7.5) –500 (-7.5) +500 (+7.5) 5 (0.075) 100 (1500) 100 (1500) 150 (2250) 7F
3000 (45) –3000 (-45) +3000 (+45) 30 (0.45) 100 (1500) 100 (1500) 150 (2250) 7H
1) The MWP (maximum working pressure; MWP = PN) for the measuring device depends on the lowest-rated element, with regard to pressure, of the selected
components, i.e. the process connection (oä36 ff) has to be taken into consideration in addition to the measuring cell (osee Table above). Also observe
pressure-temperature dependency. For the appropriate standards and further information, see oä35, "Pressure specifications" section.
2) OPL: over pressure limit depends on the lowest-rated element, with regard to pressure, of the selected components oä35, "Pressure specifications" section.
3) The minimum operating pressure indicated in the table applies to silicone oil under reference operating conditions. Min. operating pressure at 85 °C (185 °F)
for silicone oil: up to 10 mbarabs (0.15 psiabs ).
FMD77 and FMD78: Min. operating pressure: 50 mbarabs (0.75 psiabs); observe also the pressure and temperature application limits of the selected filling oil
on oä73. For vacuum applications, please observe the installation instructions on oä75 ff.
4) Version in the order code oä79 ff, feature 40 "Nominal range; PN"
5) Turn down > 100:1 on request
6) Screws oä61 ff.
7) PMD75 only
8) Minimum span that can be calibrated for PMD75: 1 mbar (0,015 psi); minimum span that can be calibrated for FMD77 and FMD78: 5 mbar (0.075 psi)
9) For PMD75 devices with CRN-approved process connections, the MWP is
• with the use of O rings: 315 bar (4725 psi)
• with the use of PTFE and CU seals: 120 bar (1800 psi)
10) "–" side: 100 bar (1500 psi)
11) 420 bar (6300 psi) only PMD75

Deltabar S
Endress+Hauser 9
Explanation of terms Explanation of the terms "turn down (TD)",
"set span" and "zero-based span"
Case 1:
•~Lower range value (LRV)~d~Upper range value
(URV)~
Example:
• Lower range value (LRV) = 0 mbar
• Upper range value (URV) = 100 mbar (1.5 psi)
• Nominal value (URL) = 500 mbar (7.5 psi)
Turn down:
•TD=URL/~URV~ 5:1
Set span:
• URV – LRV = 100 mbar (1.5 psi)
This span is based on the zero point. P01-xxxxxxxx-05-xx-xx-xx-001
Example: 500 mbar (7.5 psi) measuring cell
Case 2:
•~Lower range value (LRV)~t~Upper range value
(URV)~
Example:
• Lower range value (LRV) = –300 mbar (4.5 psi)
• Upper range value (URV) = 0 bar
• Nominal value (URL) = 500 mbar (7.5 psi)
Turn down:
•TD=URL/~(LRV)~= 1.67:1
Set span:
• URV – LRV = 300 mbar (4.5 psi)
This span is based on the zero point. P01-xMD7xxxx-05-xx-xx-xx-007
Example: 500 mbar (7.5 psi) measuring cell
1 Set span
2 Zero-based span
3 Nominal value i upper range limit (URL)
4 Nominal measuring range
5 Sensor measuring range
LRL Lower range limit
URL Upper range limit
LRV Lower range value
URV Upper range value
–500 mbar 0+500 mbar
100
LRL LRV URL
URV
➁➀
=
➂
➃
➄
–500 mbar +500 mbar
LRV URLURV
➂
0
LRL
–300 mbar
➁➀
=
➃
➄

Deltabar S
10 Endress+Hauser
Output
Output signal • 4 to 20 mA with superimposed digital communication protocol HART 5.0, 2-wire
• Digital communication signal PROFIBUS PA (Profile 3.0)
– signal coding: Manchester Bus Powered (MBP): Manchester II
– data transmission rate: 31.25 KBit/s voltage mode
• Digital communication signal FOUNDATION Fieldbus
– signal coding: Manchester Bus Powered (MBP): Manchester II
– data transmission rate: 31.25 KBit/s voltage mode
Signal range –
4to20mAHART
3.8 mA to 20.5 mA
Signal on alarm As per NAMUR NE 43
• 4 to 20 mA HART
Options:
– Max. alarm: can be set from 21 to 23 mA (Factory setting: 22 mA)
– Hold measured value: last measured value is held
– Min. alarm: 3.6 mA
• PROFIBUS PA: can be set in the Analog Input block,
Options: Last Valid Out Value (factory setting), Fail Safe Value, Status Bad
• FOUNDATION Fieldbus: can be set in the Analog Input block,
Options: Last Good Value, Fail Safe Value (factory setting), Wrong Value
Load – 4 to 20 mA HART
P01-xMD7xxxx-05-xx-xx-xx-005
Load diagram, observe the position of the jumper and the explosion protection (oä20, "Measuring a 4 to 20 mA test
signal" section.)
1 Jumper for 4 to 20 mA test signal set to "Non-test" position
2 Jumper for 4 to 20 mA test signal set to "Test" position
3 Power supply 10.5 (11.5) to 30 V DC for 1/2 G Ex ia, 1 GD Ex ia, 1/2 GD Ex ia, FM IS, CSA IS, IECEx ia, NEPSI Ex ia
4 Power supply 10.5 (11.5) to 45 V DC for device for non-hazardous areas, 1/2 D, 1/3 D, 2 G Ex d, 3 G Ex nA, FM XP,
FM DIP, FM NI, CSA XP, CSA dust ignition proof, NEPSI Ex d
RLmax Maximum load resistance
U Supply voltage
Note!
When operating via a handheld terminal or via a PC with an operating program, a minimum communication
resistance of 250 :must exist within the loop.
Resolution • Current output: 1 PA
• Display: can be set (factory setting: presentation of the maximum accuracy of the transmitter)
U – 10.5 V
R
Lmax
23 mA
≤
30
20
10.5 U
[V]
40 45
1282
1500
847
413
[]Ω
R
Lmax
30
20
11.5 U
[V]
40 45
1239
1456
804
369
[]Ω
R
Lmax
TestTest
➀➁
U – 11.5 V
R
Lmax
23 mA
≤
➂
➃
➂
➃

Deltabar S
Endress+Hauser 11
Dead time, time constant
P01-xxxxxxxx-05-xx-xx-xx-036
Presentation of the dead time and the time constant
Dynamic behavior:
current output
Dynamic behavior: digital
output (HART electronics)
A typical burst rate of 300 ms results in the following behavior:
Reading cycle
• Acyclic: max. 3/s, typical 1/s (depends on command # and number of preambles)
I
63%
100 %
t
t1t2
90%
t3
Type Measuring cell Dead time (t1)
[ms]
Time constant T63 (t2) [ms] Time constant T90 (t3) [ms]
PMD75 max. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
• 16 bar (240 psi)
45 • 450
•60
•45
•40
•60
• 1040
• 138
• 104
• 92
• 138
PMD70,
FMD76
max. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
90 • 4700
• 280
• 210
• 110
• 10810
• 644
• 483
• 253
FMD77,
FMD78
max. Dependent on the diaphragm seal
Type Measuring cell Dead time (t1) [ms] Dead time (t1) +
Time constant T63 (=t2) [ms]
Dead time (t1) +
Time constant T90 (=t3) [ms]
PMD75 min. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
• 16 bar (240 psi)
205 • 655
• 265
• 250
• 245
• 265
• 1200
• 298
• 264
• 252
• 298
max. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
• 16 bar (240 psi)
1005 • 1455
• 1065
• 1050
• 1045
• 1065
• 2000
• 1098
• 1064
• 1052
• 1098
PMD70,
FMD76
min. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
250 • 4950
• 530
• 460
• 360
• 10970
• 804
• 643
• 413
PMD70,
FMD76
max. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
1050 • 5750
• 1330
• 1260
• 1160
• 11770
• 1604
• 1443
• 1213
FMD77,
FMD78
max. Dependent on the diaphragm seal

Deltabar S
12 Endress+Hauser
• Cyclic (Burst): max. 3/s, typical 2/s
The Device commands the BURST MODE function for cyclic value transmission via the HART communication
protocol.
Cycle time (Update time)
Cyclic (Burst): min. 300 ms
Response time
• Acyclic: min. 330 ms, typical 590 ms (depends on command # and number of preambles)
• Cyclic (Burst): min. 160 ms, typical 350 ms (depends on command # and number of preambles)
Dynamic behavior:
PROFIBUS PA
A typical PLC cycle time of 1 s results in the following behavior:
Reading cycle (PLC)
• Cyclic: max. 30/s (dependent on the number and type of function blocks used in a closed-control loop)
• Acyclic: typical 25/s
Cycle time (update time)
min. 200 ms
The cycle time in a bus segment in cyclic data communication depends on the number of devices, on the
segment coupler used and on the internal PLC cycle time. A new value can be determined up to 5 times per
second.
Response time
• Cyclic: approx. 10 to 13 ms (depends on Min. Slave Interval)
• Acyclic: approx. 60 to 70 ms (depends on Min. Slave Interval)
Type Measuring cell Dead time (t1) [ms] Dead time (t1) +
Time constant T63 (=t2) [ms]
Dead time (t1) +
Time constant T90 (=t3) [ms]
PMD75 min. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
•16bar(240psi)
80 • 530
• 140
• 125
• 120
• 140
• 1075
• 173
• 139
• 127
• 173
max. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
•16bar(240psi)
1280 • 1730
• 1340
• 1325
• 1320
• 1340
• 2275
• 1373
• 1339
• 1327
• 1373
PMD70,
FMD76
min. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
125 • 4825
• 405
• 335
• 235
• 10845
• 679
• 518
• 288
PMD70,
FMD76
max. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
1325 • 6025
• 1605
• 1535
• 1435
• 12045
• 1879
• 1718
• 1488
FMD77,
FMD78
max. Dependent on the diaphragm seal

Deltabar S
Endress+Hauser 13
Dynamic behavior:
FOUNDATION Fieldbus
A typical configuration for the macro cycle time (host system) of 1 s results in the following behavior:
Reading cycle
• Cyclic: max. 10/s (dependent on the number and type of function blocks used in a closed-control loop)
• Acyclic: typical 10/s
Cycle time (update time)
Cyclic: min. 100 ms
Response time
• Cyclic: max. 20 ms (for standard bus parameter settings)
• Acyclic: typical 100 ms (for standard bus parameter settings)
Damping A damping affects all outputs (output signal, display).
• Via onsite display, handheld terminal or PC with operating program, continuous from 0 to 999 s
• Additionally for HART and PROFIBUS PA: via DIP switch on the electronic insert, switch position
"on" = set value and "off"
• Factory setting: 2 s
Type Measuring cell Dead time (t1)
[ms]
Dead time (t1) +
Time constant T63 (=t2) [ms]
Dead time (t1) +
Time constant T90 (=t3) [ms]
PMD75 min. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
• 16 bar (240 psi)
90 • 540
• 150
• 135
• 130
• 150
• 1085
• 183
• 149
• 137
• 183
max. • 10 mbar (0.15 psi) and 30 mbar (0.45 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
• 16 bar (240 psi)
1090 • 1540
• 1150
• 1135
• 1130
• 1150
• 2085
• 1183
• 1149
• 1137
• 1183
PMD70,
FMD76
min. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
135 • 4835
• 415
• 345
• 245
• 10855
• 689
• 528
• 298
PMD70,
FMD76
max. • 25 mbar (0.375 psi)
• 100 mbar (1.5 psi)
• 500 mbar (7.5 psi)
• 3 bar (45 psi)
1135 • 5835
• 1415
• 1345
• 1245
• 11855
• 1689
• 1528
• 1298
FMD77,
FMD78
max. Dependent on the diaphragm seal

Deltabar S
14 Endress+Hauser
Protocol-specific data HART
PROFIBUS PA
Manufacturer ID 17 (11 hex)
Device Type Code 23 (17 hex)
Device Revision 21 (15 hex) - SW version 02.1y.zz
HART spezification 5
DD Revision • 4 (russian in language selection)
• 3 (netherlands in language selection)
Device description files
(DTM, DD)
Information and files can be found:
• www.endress.com
• www.hartcomm.org
HART load Min. 250 :
HART device variables The measured values can be freely assigned to the device variables:
Measured values for PV (primary variable)
• Pressure
•Flow
• Level
• Tank content
Measured values for SV, TV (second and third variable)
• Pressure
• Totalizer
Measured values for QV (fourth variable)
• Temperature
Supported functions • Burst mode
• Additional Transmitter Status
• Device Locking
• Alternative operating modes
Manufacturer ID 17 (11 hex)
Ident number 1542 hex
Profile Version 3.0
• SW Version 03.00.zz
• SW Version 04.00.zz
3.02
• SW Version 04.01.zz (Device Revision 3)
Compartibility SW version 03.00.zz and higher.
GSD Revision • 4 (SW Version 3.00.zz and 4.00.zz)
•5(DeviceRevision3)
DD Revision • 1 (SW Version 3.00.zz and 4.00.zz)
•1(DeviceRevision3)
GSD File Information and files can be found:
• www.endress.com
• www.profibus.org
DD Files
Output values Measured values for PV (über Analog Input Function Block)
• Pressure
•Flow
• Level
• Tank content
Measured values for SV
• Pressure
• Temperature
Measured values for QV
• Totalizer
Input values Input value sent from PLC, can be shown on display

Deltabar S
Endress+Hauser 15
FOUNDATION Fieldbus
Supported features • Identification & Maintenance
Simple device identification via control system and nameplate
•Condensedstatus
1)
• Automatic ident number adaptation and switchable to following ident
numbers):
– 9700: Profile-specific transmitter identification number with the "Classic" or
"Condensed" status".
– 1504: Compatibility mode for the old Deltabar S generation (FMD230,
FMD630, FMD633, PMD230, PMD235).
– 1542: Identification number for the new Deltabar S generation (FMD76,
FMD77, FMD78, PMD70, PMD75).
• Device locking: The device can be locked by hardware or software.
1) Only with Profile Version 3.02
Manufacturer ID 452B48 hex
Device type 1009 hex
Device Revision • 6 - SW Version 03.00.zz
• 7 - SW Version 04.00.zz (FF-912)
DD Revision • 3 (Device Revision 6)
•2(DeviceRevision7)
CFF Revision • 4 (Device Revision 6)
•1(DeviceRevision7)
DD Files Information and files can be found:
• www.endress.com
• www.fieldbus.org
CFF Files
Device Tester Version (ITK
Version)
• 5.0 (Device Revision 6)
• 6.01 (Device Revision 7)
ITK Test Campaign Number • IT054700 (Device Revision 6)
• IT085400 (Device Revision 7)
Link Master (LAS) capable yes
Link Master / Basic Device
selectable
Yes, default is Basic Device
Node Address Default: 247 (F7 hex)
Supported features Field Diagnostics Profile 1)
Following methods are supported:
•Restart
• Configure error as warning or alarm
•HistoROM
• Peakhold
•AlarmInfo
•SensorTrimm
1) Only with FF912
Number of VCRs • 44 (Device Revision 6)
• 24 (Device Revision 7)
Number of Link Objects in VFD 50

Deltabar S
16 Endress+Hauser
Virtual communication references (VCRs)
Link settings
Transducer Blocks
Device Revision 6 Device Revision 7
Permanent Entries 44 1
Client VCRs 0 0
Server VCRs 5 10
Source VCRs 8 43
Sink VCRs 0 0
Subscriber VCRs 12 43
Publisher VCRs 19 43
Device Revision 6 Device Revision 7
Slot time 4 4
Min. inter PDU delay 12 10
Max. response delay 10 10
Block Content Output values
TRD1 Block Contains all parameters related to the measurement • Pressure, flow or level (channel 1)
• Process temperature (channel 2)
Service Block Contains service information • Pressure after damping (channel 3)
• Pressure peakhold indicator (channel 4)
• Counter for max. pressure transgressions
(channel 5)
Dp Flow Block Contains flow and totalizer parameter Totalizer 1 (channel 6)
Diagnostic Block Contains diagnostic information Error code via DI channels (channel 0 to 16)
Display Block Contains parameters to configure the onsite display No output values

Deltabar S
Endress+Hauser 17
Function blocks
Block Content Number
of blocks
Execution time Functionality
Device
Revision 6
Device
Revision 7
Device
Revision 6
Device
Revision 7
Resource Block The Resource Block contains all the data that
uniquely identify the device. It is an electronic
version of a nameplate of the device.
1 enhanced enhanced
Analog Input Block 1
Analog Input Block 2
Analog Input Block 3
The AI Block receives the measuring data from the
Sensor Block, (selectable via a channel number) and
makes the data available to other function blocks at
its output. Enhancement: digital outputs for process
alarms, fail safe mode.
3 45 ms 45 ms 1) enhanced enhanced
Digital Input Block This block contains the discrete data of the Diagnose
Block (selectable via a channel number 0 to 16) and
provides them for other blocks at the output.
1 40 ms 30 ms standard enhanced
Digital Output Block This block converts the discrete input and thus
initiates an action (selectable via a channel number)
in the DP Flow Block or in the Service Block.
Channel 1 resets the counter for max. pressure
transgressions..
1 60 ms 40 ms standard enhanced
PID Block The PID Block serves as a proportional-integral-
derivative controller and is used almost universally
for closed-loop-control in the field including cascade
and feedforward. Input IN can be indicated on the
display. The selection is performed in the Display
Block (DISPLAY_MAIN_LINE_CONTENT).
1 120 ms 70 ms standard enhanced
Arithmetic Block This block is designed to permit simple use of popular
measurement math functions. The user does not have
to know how to write equations. The math algorithm
is selected by name, chosen by the user for the
function to be performed.
1 50 ms 40 ms standard enhanced
Input Selector Block The Input Selector Block facilitates the selection of up
to four inputs and generates an output based on the
configured action. This block normally receives its
inputs from AI Blocks. The block performs maximum,
minimum, average and ‘first good’ signal selection.
Inputs IN1 to IN4 can be indicated on the display.
The selection is performed in the Display Block
(DISPLAY_MAIN_LINE_CONTENT).
1 35 ms 35 ms standard enhanced
Signal Characterizer Block The Signal Characterizer Block has two sections,
each with an output that is a non-linear function of
the respective input. The non-linear function is
generated by a single look-up table with 21 arbitrary
x-y pairs.
1 30 ms 40 ms standard enhanced
Integrator Block The Integrator Block integrates a variable as a
function of the time or accumulates the counts from a
Pulse Input Block. The block may be used as a
totalizer that counts up until reset or as a batch
totalizer that has a setpoint, where the integrated or
accumulated value is compared to pre-trip and trip
settings, generating a binary signal when the setpoint
is reached.
1 35 ms 40 ms standard enhanced
Analog Alarm Block This block contains all process alarm conditions
(working like a comparator) and represents them at
the output.
1 35 ms 35 ms standard enhanced
Additional function block information:
Instantiate Function Block YES YES
Number of additional instantiate blocks 94
1) Without trend and alarm reports

Deltabar S
18 Endress+Hauser
Power supply
Electrical connection Note!
• When using the measuring device in hazardous areas, installation must comply with the corresponding
national standards and regulations and the Safety Instructions or Installation or Control Drawings. oä95,
"Safety Instructions" and "Installation/Control Drawings" sections.
• Devices with integrated overvoltage protection must be grounded. oä33.
• Protective circuits against reverse polarity, HF influences and overvoltage peaks are installed.
4 to 20 mA HART
P01-xMx7xxxx-04-xx-xx-xx-001
Electrical connection 4 to 20 mA HART
1 Housing
2 Jumper for 4 to 20 mA test signal. See oä20, "Measuring a 4 to 20 mA test signal" section.
3 Internal ground terminal
4 External ground terminal
5 4 to 20 mA test signal between positive and test terminal
6 Minimum supply voltage = 10.5 V DC, jumper is set as illustrated in the diagram.
7 Minimum supply voltage = 11.5 V DC, jumper is inserted in "Test" position.
8 Devices with integrated overvoltage protection are labeled OVP (overvoltage protection) here (oä33).
PROFIBUS PA
The digital communication signal is transmitted to the bus via a 2-wire connection. The bus also provides the
power supply. For further information on the network structure and grounding, and for further bus system
components such as bus cables, see the relevant documentation, e.g. Operating Instructions BA00034S
"PROFIBUS DP/PA: Guidelines for planning and commissioning" and the PNO Guideline.
Cable specifications:
• Use a twisted, shielded two-wire cable, preferably cable type A
Note!
For further information on the cable specifications, see Operating Instructions BA00034S
"PROFIBUS DP/PA: Guidelines for planning and commissioning", the PNO Guideline 2.092
PROFIBUS PA User and Installation Guideline" and IEC 61158-2 (MBP).
4…20mA
➅
10.5V DC
➆
11.5V DC
4... 20mATest
Te s t
➀
➁
➂
➃
➄
Test
➇
4... 20mA Test

Deltabar S
Endress+Hauser 19
FOUNDATION Fieldbus
The digital communication signal is transmitted to the bus via a 2-wire connection. The bus also provides the
power supply. For further information on the network structure and grounding and for further bus system
components such as bus cables, see the relevant documentation, e.g. Operating Instructions BA00013S
"FOUNDATION Fieldbus Overview" and the FOUNDATION Fieldbus Guideline.
Cable specifications:
• Use a twisted, shielded two-wire cable, preferably cable type A
Note!
For further information on the cable specifications, see Operating Instructions BA00013S "FOUNDATION
Fieldbus Overview", FOUNDATION Fieldbus Guideline and IEC 61158-2 (MBP).
Devices with Harting plug Han7D
P01-xMD7xxxx-04-xx-xx-xx-000
Left: electrical connection for devices with Harting plug Han7D
Right: view of the plug connector at the device
Material: CuZn, gold-plated plug-in jack and plug
Devices with M12 plug
PIN assignment for M12 connector
Endress+Hauser offers the following accessories for devices with an M12 plug:
Plug-in jack M 12x1, straight
• Material: body PA; coupling nut CuZn, nickel-plated
• Degree of protection (fully locked): IP67
• Order number: 52006263
Plug-in jack M 12x1, elbowed
• Material: body PBT/PA; coupling nut GD-Zn, nickel-plated
• Degree of protection (fully locked): IP67
• Order number: 71114212
Cable 4x0.34 mm² (20 AWG) with M12 socket, elbowed, screw plug, length 5 m (16 ft)
• Material: body PUR; coupling nut CuSn/Ni; cable PVC
• Degree of protection (fully locked): IP67
• Order number: 52010285
Han7D
–
+
+–
–
+
1
5
4
6
7
8
2
3
A0011175
PIN Meaning
1 Signal +
2 Not assigned
3 Signal –
4Earth
21
3
4
+
–
nc

Deltabar S
20 Endress+Hauser
Devices with 7/8" plug
PIN assignment for 7/8" connector
External thread: 7/8 - 16 UNC
• Material: 316L (1.4401)
• Degree of protection: IP68
Cable gland
Terminals
For wire cross-sections of 0.5 to 2.5 mm² (20 to 14 AWG)
Measuring a 4 to 20 mA test signal
A 4 to 20 mA test signal may be measured via the positive and test terminal without interrupting the
measurement. The minimum supply voltage of the device can be reduced by simply changing the position of
the jumper. As a result, operation is also possible with lower voltage sources. Observe the position of the jumper
in accordance with the following table.
A0011176
PIN Meaning
1 Signal –
2 Signal +
3Notassigned
4Shield
Approval Type Clamping area
Standard, II1/2G Exia, IS Plastic M20x1.5 5 to 10 mm (0.2 to 0.39 in)
ATEX II1/2D, II1/3D,
II1/2GD Exia, II1GD Exia
II3G Ex nA
Metal M20x1.5 (Ex e) 7 to 10.5 mm (0.28 to 0.41 in)
Jumper position for test signal Description
– Measuring 4 to 20 mA test signal via the plus and test terminal:
possible. (Thus, the output current can be measured without
interruption via the diode.)
– Delivery status
– Minimum supply voltage: 11.5 V DC
– Measuring 4 to 20 mA test signal via the plus and test terminal:
not possible.
– Minimum supply voltage: 10.5 V DC
2
1
4
3
Test
Test
Test