Endress+Hauser Proline Prowirl F 200 User manual

Products Solutions Services
Operating Instructions
Proline Prowirl F 200
PROFIBUS PA
Vortex flowmeter
BA01222D/06/EN/03.15
71299421
Valid as of version
01.01.zz (Device firmware)

Proline Prowirl F 200 PROFIBUS PA
2 Endress+Hauser
• Make sure the document is stored in a safe place such that it is always available when
working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser Sales Center will supply you with current information and updates to
these instructions.

Proline Prowirl F 200 PROFIBUS PA Table of contents
Endress+Hauser 3
Table of contents
1 Document information .............. 6
1.1 Document function ..................... 6
1.2 Symbols used .......................... 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Tool symbols .................... 6
1.2.4 Symbols for certain types of
information .................... 7
1.2.5 Symbols in graphics ............... 7
1.3 Documentation ........................ 7
1.3.1 Standard documentation ........... 8
1.3.2 Supplementary device-dependent
documentation .................. 8
1.4 Registered trademarks ................... 8
2 Basic safety instructions ............ 9
2.1 Requirements for the personnel ............ 9
2.2 Designated use ........................ 9
2.3 Workplace safety ...................... 10
2.4 Operational safety ..................... 10
2.5 Product safety ........................ 10
2.6 IT security ........................... 10
3 Product description ................ 11
3.1 Product design ........................ 11
4 Incoming acceptance and product
identification ..................... 12
4.1 Incoming acceptance ................... 12
4.2 Product identification ................... 12
4.2.1 Transmitter nameplate ........... 13
4.2.2 Sensor nameplate ............... 14
4.2.3 Symbols on measuring device ...... 16
5 Storage and transport ............. 17
5.1 Storage conditions ..................... 17
5.2 Transporting the product ................ 17
5.2.1 Measuring devices without lifting
lugs ......................... 17
5.2.2 Measuring devices with lifting lugs .. 18
5.2.3 Transporting with a fork lift ........ 18
5.3 Packaging disposal ..................... 18
6 Installation ....................... 19
6.1 Installation conditions .................. 19
6.1.1 Mounting position ............... 19
6.1.2 Requirements from environment and
process ....................... 23
6.1.3 Special mounting instructions ...... 24
6.2 Mounting the measuring device ........... 25
6.2.1 Required tools .................. 25
6.2.2 Preparing the measuring device ..... 25
6.2.3 Mounting the sensor ............. 25
6.2.4 Mounting the transmitter of the
remote version ................. 26
6.2.5 Turning the transmitter housing .... 27
6.2.6 Turning the display module ........ 27
6.3 Post-installation check .................. 28
7 Electrical connection .............. 29
7.1 Connection conditions .................. 29
7.1.1 Required tools .................. 29
7.1.2 Connecting cable requirements ..... 29
7.1.3 Terminal assignment ............. 32
7.1.4 Pin assignment, device plug ........ 33
7.1.5 Shielding and grounding .......... 33
7.1.6 Requirements for the supply unit .... 34
7.1.7 Preparing the measuring device ..... 35
7.2 Connecting the measuring device .......... 35
7.2.1 Connecting the remote version ..... 35
7.2.2 Connecting the transmitter ........ 39
7.2.3 Ensuring potential equalization ..... 41
7.3 Special connection instructions ............ 41
7.3.1 Connection examples ............. 41
7.4 Hardware settings ..................... 42
7.4.1 Setting the device address ......... 42
7.5 Ensuring the degree of protection .......... 43
7.6 Post-connection check .................. 44
8 Operation options ................. 45
8.1 Overview of operating options ............ 45
8.2 Structure and function of the operating
menu .............................. 46
8.2.1 Structure of the operating menu .... 46
8.2.2 Operating philosophy ............ 47
8.3 Access to the operating menu via the local
display ............................. 48
8.3.1 Operational display .............. 48
8.3.2 Navigation view ................ 49
8.3.3 Editing view ................... 51
8.3.4 Operating elements .............. 52
8.3.5 Opening the context menu ......... 53
8.3.6 Navigating and selecting from list ... 55
8.3.7 Calling the parameter directly ...... 55
8.3.8 Calling up help text .............. 56
8.3.9 Changing the parameters ......... 57
8.3.10 User roles and related access
authorization .................. 58
8.3.11 Disabling write protection via access
code ......................... 58
8.3.12 Enabling and disabling the keypad
lock ......................... 58
8.4 Access to the operating menu via the
operating tool ........................ 59
8.4.1 Connecting the operating tool ...... 59

Table of contents Proline Prowirl F 200 PROFIBUS PA
4 Endress+Hauser
8.4.2 FieldCare ..................... 61
8.4.3 SIMATIC PDM .................. 62
9 System integration ................ 63
9.1 Overview of device description files ......... 63
9.1.1 Current version data for the device ... 63
9.1.2 Operating tools ................. 63
9.2 Device master file (GSD) ................. 63
9.2.1 Manufacturer-specific GSD ........ 64
9.2.2 Profile GSD .................... 64
9.2.3 Compatibility with other Endress
+Hauser measuring devices ........ 64
9.3 Cyclic data transmission ................ 65
9.3.1 Block model ................... 65
9.3.2 Description of the modules ........ 66
10 Commissioning .................... 72
10.1 Function check ....................... 72
10.2 Switching on the measuring device ......... 72
10.3 Configuring the device address via software .. 72
10.3.1 PROFIBUS network .............. 72
10.4 Setting the operating language ............ 72
10.5 Configuring the measuring device .......... 74
10.5.1 Defining the tag name ............ 74
10.5.2 Selecting and setting the medium ... 76
10.5.3 Setting the system units .......... 78
10.5.4 Configuring the analog inputs ...... 81
10.5.5 Configuring the local display ....... 82
10.5.6 Configuring communication
interface ...................... 83
10.5.7 Configuring the low flow cut off ..... 84
10.6 Advanced settings ..................... 86
10.6.1 Setting the medium properties ...... 87
10.6.2 Performing external compensation .101
10.6.3 Carrying out a sensor adjustment ... 103
10.6.4 Configuring the pulse/frequency/
switch output ................. 104
10.6.5 Configuring the totalizer ......... 116
10.6.6 Carrying out additional display
configurations ................. 118
10.7 Configuration management ............. 120
10.7.1 Function scope of the "Configuration
management" parameter ......... 121
10.8 Simulation .......................... 122
10.9 Protecting settings from unauthorized
access ............................. 124
10.9.1 Write protection via access code ... 124
10.9.2 Write protection via write protection
switch ....................... 125
11 Operation ....................... 127
11.1 Reading the device locking status ......... 127
11.2 Adjusting the operating language ......... 127
11.3 Configuring the display ................ 127
11.4 Reading measured values ............... 127
11.4.1 Process variables ............... 127
11.4.2 Totalizer ..................... 130
11.4.3 Output values ................. 131
11.5 Adapting the measuring device to the process
conditions .......................... 131
11.6 Performing a totalizer reset ............. 131
11.7 Showing data logging ................. 132
12 Diagnostics and troubleshooting .. 135
12.1 General troubleshooting ................ 135
12.2 Diagnostic information on local display ..... 137
12.2.1 Diagnostic message ............. 137
12.2.2 Calling up remedial measures ..... 139
12.3 Diagnostic information in FieldCare ....... 139
12.3.1 Diagnostic options .............. 139
12.3.2 Calling up remedy information .... 140
12.4 Adapting the diagnostic information ...... 141
12.4.1 Adapting the measured value and
device status .................. 141
12.4.2 Adapting the diagnostic behavior ... 142
12.5 Overview of diagnostic information ....... 145
12.5.1 Diagnostic of sensor ............ 145
12.5.2 Diagnostic of electronic .......... 148
12.5.3 Diagnostic of configuration ....... 155
12.5.4 Diagnostic of process ............ 162
12.6 Pending diagnostic events .............. 170
12.7 Diagnostic list ....................... 171
12.8 Event logbook ....................... 171
12.8.1 Event history .................. 171
12.8.2 Filtering the event logbook ....... 171
12.8.3 Overview of information events .... 172
12.9 Resetting the measuring device .......... 173
12.9.1 Function scope of the "Device reset"
parameter .................... 173
12.10 Device information ................... 173
12.11 Firmware history ..................... 176
13 Maintenance .................... 177
13.1 Maintenance tasks .................... 177
13.1.1 Exterior cleaning ............... 177
13.1.2 Interior cleaning ............... 177
13.1.3 Replacing seals ................ 177
13.2 Measuring and test equipment ........... 177
13.3 Endress+Hauser services ............... 177
14 Repair ........................... 178
14.1 General notes ....................... 178
14.2 Spare parts ......................... 178
14.3 Endress+Hauser services ............... 179
14.4 Return ............................. 179
14.5 Disposal ........................... 179
14.5.1 Removing the measuring device .... 179
14.5.2 Disposing of the measuring device .. 180
15 Accessories ...................... 181
15.1 Device-specific accessories .............. 181
15.1.1 For the transmitter ............. 181
15.1.2 For the sensor ................. 182

Proline Prowirl F 200 PROFIBUS PA Table of contents
Endress+Hauser 5
15.2 Service-specific accessories .............. 182
15.3 System components ................... 183
16 Technical data ................... 184
16.1 Application ......................... 184
16.2 Function and system design ............. 184
16.3 Input .............................. 184
16.4 Output ............................ 190
16.5 Power supply ........................ 193
16.6 Performance characteristics ............. 195
16.7 Installation ......................... 198
16.8 Environment ........................ 198
16.9 Process ............................ 199
16.10 Mechanical construction ............... 200
16.11 Operability ......................... 207
16.12 Certificates and approvals .............. 209
16.13 Application packages .................. 210
16.14 Accessories ......................... 211
16.15 Supplementary documentation ........... 211
Index ................................. 213

Document information Proline Prowirl F 200 PROFIBUS PA
6 Endress+Hauser
1 Document information
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols used
1.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is
grounded via a grounding system.
Protective ground connection
A terminal which must be connected
to ground prior to establishing any
other connections.
Equipotential connection
A connection that has to be connected
to the plant grounding system: This
may be a potential equalization line
or a star grounding system depending
on national or company codes of
practice.
1.2.3 Tool symbols
Symbol Meaning
Flat blade screwdriver
Allen key
Open-ended wrench

Proline Prowirl F 200 PROFIBUS PA Document information
Endress+Hauser 7
1.2.4 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation
Reference to page
Reference to graphic
,… ,
Series of steps
Result of a step
Help in the event of a problem
Visual inspection
1.2.5 Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
1.3 Documentation
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.
For a detailed list of the individual documents along with the documentation code

Document information Proline Prowirl F 200 PROFIBUS PA
8 Endress+Hauser
1.3.1 Standard documentation
Document type Purpose and content of the document
Technical Information Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Brief Operating Instructions Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information
from incoming acceptance to initial commissioning.
1.3.2 Supplementary device-dependent documentation
Additional documents are supplied depending on the device version ordered: Always
comply strictly with the instructions in the supplementary documentation. The
supplementary documentation is an integral part of the device documentation.
1.4 Registered trademarks
PROFIBUS®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
KALREZ ®, VITON ®
Registered trademarks of DuPont Performance Elastomers L.L.C., Wilmington, DE USA
GYLON®
Registered trademark of Garlock Sealing Technologies, Palmyar, NY, USA
Applicator®, FieldCare®, DeviceCare ®, Field XpertTM, HistoROM®, Heartbeat
TechnologyTM
Registered or registration-pending trademarks of the Endress+Hauser Group

Proline Prowirl F 200 PROFIBUS PA Basic safety instructions
Endress+Hauser 9
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the
instructions in the Operating Instructions and supplementary documentation as well as
in the certificates (depending on the application)
‣Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
‣Being instructed and authorized according to the requirements of the task by the
facility's owner-operator
‣Following the instructions in these Operating Instructions
2.2 Designated use
Application and media
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or in applications
where there is an increased risk due to process pressure, are labeled accordingly on the
nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Only use the measuring device in full compliance with the data on the nameplate and
the general conditions listed in the Operating Instructions and supplementary
documentation.
‣Check the nameplate to verify if the device ordered can be put to its intended use in the
approval-related area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media against which the process-wetted materials
are adequately resistant.
‣If the measuring device is not operated at atmospheric temperature, compliance with
the relevant basic conditions specified in the associated device documentation is
absolutely essential: "Documentation" section →  7.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.
LWARNING
Danger of breakage of the sensor due to corrosive or abrasive fluids or from
environmental conditions!
‣Verify the compatibility of the process fluid with the sensor material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance
in verifying the corrosion resistance of fluid-wetted materials, but does not accept any

Basic safety instructions Proline Prowirl F 200 PROFIBUS PA
10 Endress+Hauser
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
Possible burn hazard due to fluid temperatures!
‣For elevated fluid temperature, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣It is recommended to wear gloves on account of the higher risk of electric shock.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from Endress+Hauser only.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which it is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.
2.6 IT security
We only provide a warranty if the device is installed and used as described in the
Operating Instructions. The device is equipped with security mechanisms to protect it
against any inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.

Proline Prowirl F 200 PROFIBUS PA Product description
Endress+Hauser 11
3 Product description
The device consists of a transmitter and a sensor.
Two device versions are available:
• Compact version – transmitter and sensor form a mechanical unit.
• Remote version - transmitter and sensor are mounted in separate locations.
3.1 Product design
1 2 345 6 78
9
+E
–
A0020649
 1 Important components of a measuring device
1 Electronics compartment cover
2 Display module
3 Main electronics module
4 Cable glands
5 Transmitter housing (incl. HistoROM)
6 I/O electronics module
7 Terminals (pluggable spring terminals)
8 Connection compartment cover
9 Sensor

Incoming acceptance and product identification Proline Prowirl F 200 PROFIBUS PA
12 Endress+Hauser
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
1
+
2
1
+
2
Are the order codes on the
delivery note (1) and the
product sticker (2)
identical?
Are the goods undamaged?
Do the nameplate data
match the ordering
information on the delivery
note?
Is the CD-ROM with the
Technical Documentation
(depends on device
version) and documents
present?
• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.
• Depending on the device version, the CD-ROM might not be part of the delivery!
The Technical Documentation is available via the Internet or via the Endress+Hauser
Operations App, see the "Product identification" section →  13.
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is
displayed.
• Enter the serial number from the nameplates into the Endress+Hauser Operations App
or scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser
Operations App: all the information for the measuring device is displayed.

Proline Prowirl F 200 PROFIBUS PA Incoming acceptance and product identification
Endress+Hauser 13
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The chapters "Additional standard documentation on the device" →  8 and
"Supplementary device-dependent documentation" →  8
• The W@M Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or
scan the 2-D matrix code (QR code) on the nameplate.
4.2.1 Transmitter nameplate
Order code:
Ext. ord. cd.:
Ser. no.:
Date:
i
i
Patents
322540-0001
1
2
345
6
7
8
9
10 11 12
14
15
16
17
13
A0013906
 2 Example of a transmitter nameplate
1 Manufacturing location
2 Name of the transmitter
3 Order code
4 Serial number (Ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Electrical connection data, e.g. available inputs and outputs, supply voltage
7 Type of cable glands
8 Permitted ambient temperature (Ta)
9 Firmware version (FW) from the factory
10 CE mark, C-Tick
11 Additional information on version: certificates, approvals
12 Permitted temperature range for cable
13 Manufacturing date: year-month
14 Degree of protection
15 Approval information for explosion protection
16 Document number of safety-related supplementary documentation
17 2-D matrix code

Incoming acceptance and product identification Proline Prowirl F 200 PROFIBUS PA
14 Endress+Hauser
4.2.2 Sensor nameplate
Order code for "Housing" option B "GT18 two-chamber, 316L" and option K "GT18
two-chamber, remote, 316L"
Ser. no.:
Ptest:
Size:
Materials:
Gasket:
Tm:
Qmax(G):
Ta:
1
2 6
7
8
3
9
10
13 12
4 5
14 11
A0020760
 3 Example of a sensor nameplate
1 Name of the sensor
2 Nominal diameter of the sensor
3 Flange nominal diameter/nominal pressure
4 Serial number (Ser. no.)
5 Measuring tube material
6 Measuring tube material
7 Maximal permitted volume flow (gas/steam)
8 Test pressure of the sensor
9 Seal material
10 Document number of safety-related supplementary documentation →  211
11 Ambient temperature range
12 CE mark
13 Medium temperature range
14 Degree of protection

Proline Prowirl F 200 PROFIBUS PA Incoming acceptance and product identification
Endress+Hauser 15
Order code for "Housing" option C "GT20 two-chamber, aluminum coated"
Ser. no.:
Ptest:
Size:
Materials:
Tm:
Qmax(G):
Gasket:
Ta:
1
2
56 8
7
9
34
10
111213
A0020758
 4 Example of a sensor nameplate
1 Nominal diameter of the sensor
2 Flange nominal diameter/nominal pressure
3 Measuring tube material
4 Measuring tube material
5 Serial number (Ser. no.)
6 Maximal permitted volume flow (gas/steam)
7 Test pressure of the sensor
8 Degree of protection
9 Approval information for explosion protection and Pressure Equipment Directive
10 CE mark
11 Seal material
12 Medium temperature range
13 Ambient temperature range

Incoming acceptance and product identification Proline Prowirl F 200 PROFIBUS PA
16 Endress+Hauser
Order code for "Housing" option J "GT20 two-chamber, remote, aluminum coated"
Order code:
Ext. ord. cd.:
Ser. no.:
Ptest:
Size:
Ta:
Materials:
Gasket:
Tm:
Qmax(G):
4
1
5
8
12
27
9
10
11
13141516
36
A0020759
 5 Example of a sensor nameplate
1 Name of the sensor
2 Nominal diameter of the sensor
3 Flange nominal diameter/nominal pressure
4 Order code
5 Serial number (Ser. no.)
6 Extended order code (Ext. ord. cd.)
7 Maximal permitted volume flow (gas/steam)
8 Degree of protection
9 Approval information for explosion protection and Pressure Equipment Directive
10 Ambient temperature range
11 Document number of safety-related supplementary documentation →  211
12 Test pressure of the sensor
13 Measuring tube material
14 Measuring tube material
15 Seal material
16 Medium temperature range
Order code
The measuring device is reordered using the order code.
Extended order code
• The device type (product root) and basic specifications (mandatory features) are
always listed.
• Of the optional specifications (optional features), only the safety and approval-
related specifications are listed (e.g. LA). If other optional specifications are also
ordered, these are indicated collectively using the # placeholder symbol (e.g. #LA#).
• If the ordered optional specifications do not include any safety and approval-related
specifications, they are indicated by the + placeholder symbol (e.g. XXXXXX-ABCDE
+).
4.2.3 Symbols on measuring device
Symbol Meaning
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious
or fatal injury.
Reference to documentation
Refers to the corresponding device documentation.
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.

Proline Prowirl F 200 PROFIBUS PA Storage and transport
Endress+Hauser 17
5 Storage and transport
5.1 Storage conditions
Observe the following notes for storage:
• Store in the original packaging to ensure protection from shock.
• Do not remove protective covers or protective caps installed on process connections.
They prevent mechanical damage to the sealing surfaces and contamination in the
measuring tube.
• Protect from direct sunlight to avoid unacceptably high surface temperatures.
• Store in a dry and dust-free place.
• Do not store outdoors.
Storage temperature:
– All components apart from the display modules: –50 to +80 °C (–58 to +176 °F)
– Display modules: –40 to +80 °C (–40 to +176 °F)
5.2 Transporting the product
Transport the measuring device to the measuring point in the original packaging.
A0015604
Do not remove protective covers or caps installed on process connections. They
prevent mechanical damage to the sealing surfaces and contamination in the
measuring tube.
5.2.1 Measuring devices without lifting lugs
LWARNING
Center of gravity of the measuring device is higher than the suspension points of the
webbing slings.
Risk of injury if the measuring device slips.
‣Secure the measuring device against slipping or turning.
‣Observe the weight specified on the packaging (stick-on label).
A0015606

Storage and transport Proline Prowirl F 200 PROFIBUS PA
18 Endress+Hauser
5.2.2 Measuring devices with lifting lugs
LCAUTION
Special transportation instructions for devices with lifting lugs
‣Only use the lifting lugs fitted on the device or flanges to transport the device.
‣The device must always be secured at two lifting lugs at least.
5.2.3 Transporting with a fork lift
If transporting in wood crates, the floor structure enables the crates to be lifted lengthwise
or at both sides using a forklift.
5.3 Packaging disposal
All packaging materials are environmentally friendly and 100% recyclable:
• Measuring device secondary packaging: polymer stretch film that conforms to EC
Directive 2002/95/EC (RoHS).
• Packaging:
– Wood crate, treated in accordance with ISPM 15 standard, which is confirmed by the
affixed IPPC logo.
or
– Carton in accordance with European Packaging Directive 94/62EC; recyclability is
confirmed by the affixed RESY symbol.
• Seaworthy packaging (optional): Wood crate, treated in accordance with ISPM 15
standard, which is confirmed by the affixed IPPC logo.
• Carrying and mounting hardware:
– Disposable plastic pallet
– Plastic straps
– Plastic adhesive strips
• Dunnage: Paper cushion

Proline Prowirl F 200 PROFIBUS PA Installation
Endress+Hauser 19
6 Installation
6.1 Installation conditions
6.1.1 Mounting position
Mounting location
A0015543
Orientation
The direction of the arrow on the sensor nameplate helps you to install the sensor
according to the flow direction (direction of medium flow through the piping).
Vortex meters require a fully developed flow profile as a prerequisite for correct volume
flow measurement. Therefore, please note the following:
Orientation Compact version Remote version
AVertical orientation
A0015545
 1) 
BHorizontal orientation, transmitter head up
A0015589
 2) 3) 
CHorizontal orientation, transmitter head down
A0015590
 4) 5) 
DHorizontal orientation, transmitter head at side
A0015592
 4) 
1) In the case of liquids, there should be upward flow in vertical pipes to avoid partial pipe filling (Fig. A).
Disruption in flow measurement! In the case of vertical orientation and downward flowing liquid, the pipe
always needs to be completely filled to ensure correct liquid flow measurement.
2) Danger of electronics overheating! If the fluid temperature is ≥ 200 °C (392 °F) orientation B is not
permitted for the wafer version (Prowirl D) with nominal diameters DN 100 (4") and DN 150 (6").
3) In the case of hot media (e.g. steam or fluid temperature (TM) ≥ 200 °C (392 °F): orientation C or D
4) In the case of very cold media (e.g. liquid nitrogen): orientation B or D
5) For "wet steam detection/measurement" option: orientation C

Installation Proline Prowirl F 200 PROFIBUS PA
20 Endress+Hauser
Minimum spacing and cable length
A
L
A0019211
A Minimum spacing in all directions
L Required cable length
The following dimensions must be observed to guarantee problem-free access to the device
for service purposes:
• A =100 mm (3.94 in)
• L = L + 150 mm (5.91 in)
Rotating the electronics housing and the display
The electronics housing can be rotated continuously by 360 °° on the housing support. The
display unit can be rotated in 45 ° stages. This means you can read the display comfortably
from all directions.
Inlet and outlet runs
To attain the specified level of accuracy of the measuring device, the inlet and outlet runs
mentioned below must be maintained at the very minimum.