Endress+Hauser Cerabar PMP23 User manual

Products Solutions Services
Operating Instructions
Cerabar PMP23
IO-Link
Process pressure measurement
Pressure transducer for safe measurement and
monitoring of absolute and gauge pressure
BA01784P/00/EN/03.23-00
71621486
2023-07-11

Cerabar PMP23 IO-Link
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
• Make sure the document is stored in a safe place such that it is always available when
working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser distributor will supply you with current information and updates to this
manual.

Cerabar PMP23 IO-Link Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 4
1.1 Document function ..................... 4
1.2 Symbols used .......................... 4
1.3 Documentation ........................ 5
1.4 Terms and abbreviations ................. 6
1.5 Turn down calculation ................... 6
1.6 Registered trademarks ................... 7
2 Basic safety instructions ............ 8
2.1 Requirements concerning the staff .......... 8
2.2 Intended use .......................... 8
2.3 Workplace safety ....................... 9
2.4 Operational safety ...................... 9
2.5 Product safety ......................... 9
3 Product description ................ 10
3.1 Product design ........................ 10
3.2 Operating principle .................... 10
4 Incoming acceptance and product
identification ..................... 11
4.1 Incoming acceptance ................... 11
4.2 Product identification ................... 12
4.3 Storage and transport .................. 12
5 Mounting ......................... 14
5.1 Installation conditions .................. 14
5.2 Influence of orientation ................. 14
5.3 Mounting location ..................... 15
5.4 Mounting the profiled seal for the universal
process adapter ....................... 16
5.5 Post-mounting check ................... 16
6 Electrical connection .............. 17
6.1 Connecting the measuring unit ............ 17
6.2 Connection data ....................... 18
6.3 Post-connection check .................. 18
7 Operation options ................. 19
7.1 Operation with operating menu ........... 19
8 System integration ................ 20
8.1 Process data ......................... 20
8.2 Reading out and writing device data (ISDU –
Indexed Service Data Unit) ............... 21
9 Commissioning .................... 28
9.1 Function check ....................... 28
9.2 Commissioning with an operating menu ..... 28
9.3 Configuring pressure measurement ........ 29
9.4 Performing position adjustment ........... 31
9.5 Configuring process monitoring ........... 33
9.6 Current output ........................ 34
9.7 Application examples ................... 36
10 Diagnostics and troubleshooting ... 37
10.1 Troubleshooting ...................... 37
10.2 Diagnostic events ...................... 38
10.3 Behavior of the device in the event of a fault .. 40
10.4 Behavior of the current output in the event of
a fault .............................. 40
10.5 Resetting to factory settings (reset) ........ 41
11 Maintenance ...................... 41
11.1 Exterior cleaning ...................... 41
12 Repair ............................ 42
12.1 General notes ........................ 42
12.2 Return .............................. 42
12.3 Disposal ............................ 42
13 Overview of the operating menu ... 43
13.1 Without Smart Sensor Profile ............. 43
13.2 With Smart Sensor Profile ............... 44
14 Description of device parameters ... 46
14.1 Identification ......................... 46
14.2 Diagnosis ........................... 47
14.3 Parameter ........................... 49
14.4 Observation ......................... 65
15 Accessories ....................... 66
15.1 Weld-in adapter ...................... 66
15.2 Process adapter M24 ................... 66
15.3 Flush mount pipe connections M24 ........ 67
15.4 M12 plug-in jack ...................... 67
Index .................................. 69

About this document Cerabar PMP23 IO-Link
4 Endress+Hauser
1 About this document
1.1 Document function
These Operating Instructions contain all the information required in the various life cycle
phases of the device: from product identification, incoming acceptance and storage, to
installation, connection, operation and commissioning, through to troubleshooting,
maintenance and disposal.
1.2 Symbols used
1.2.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Protective earth (PE)
Ground terminals, which must be grounded prior to establishing any other connections.
The ground terminals are located on the inside and outside of the device.
Ground connection
Grounded clamp, which is grounded via a grounding system.
1.2.3 Tool symbols
Open-ended wrench
1.2.4 Symbols for certain types of information
Permitted
Procedures, processes or actions that are permitted.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information
Reference to documentation
1.
,
2.
,
3.
Series of steps

Cerabar PMP23 IO-Link About this document
Endress+Hauser 5
Reference to page:
Result of an individual step:
1.2.5 Symbols in graphics
A, B, C ... View
1, 2, 3 ... Item numbers
1.
,
2.
,
3.
Series of steps
1.3 Documentation
The following document types are available in the Downloads area of the Endress+Hauser
website (www.endress.com/downloads):
For an overview of the scope of the associated Technical Documentation, refer to the
following:
•Device Viewer (www.endress.com/deviceviewer): Enter the serial number from the
nameplate
•Endress+Hauser Operations app: Enter serial number from nameplate or scan
matrix code on nameplate.
1.3.1 Technical Information (TI)
Planning aid
The document contains all the technical data on the device and provides an overview of
the accessories and other products that can be ordered for the device.
1.3.2 Brief Operating Instructions (KA)
Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information from incoming
acceptance to initial commissioning.

About this document Cerabar PMP23 IO-Link
6 Endress+Hauser
1.4 Terms and abbreviations
URL OPLMWP
LRL
0
p
LRV URV
1
2
3
4
A0029505
1 OPL: The OPL (over pressure limit = sensor overload limit) for the measuring device depends on the lowest-
rated element, with regard to pressure, of the selected components, i.e. the process connection has to be taken
into consideration in addition to the measuring cell. Observe pressure-temperature dependency. The OPL may
only be applied for a short period of time.
2 MWP: The MWP (maximum working pressure) for the sensors depends on the lowest-rated element, with
regard to pressure, of the selected components, i.e. the process connection has to be taken into consideration
in addition to the measuring cell. Observe pressure-temperature dependency. The maximum working pressure
may be applied at the device for an unlimited period. The MWP can be found on the nameplate.
3 The maximum sensor measuring range corresponds to the span between the LRL and URL. This sensor
measuring range is equivalent to the maximum calibratable/adjustable span.
4 The calibrated/adjusted span corresponds to the span between the LRV and URV. Factory setting: 0 to URL.
Other calibrated spans can be ordered as customized spans.
p Pressure
LRL Lower range limit
URL Upper range limit
LRV Lower range value
URV Upper range value
TD Turn down. Example - see the following section.
The turn down is preset at the factory and cannot be changed.
1.5 Turn down calculation
LRV URLURV LRL
1 = 2 3
A0029545
1 Calibrated/adjusted span
2 Zero point-based span
3 Upper range limit
Example:
• Measuring cell: 10 bar (150 psi)
• Upper range limit (URL) = 10 bar (150 psi)
• Calibrated/adjusted span: 0 to 5 bar (0 to 75 psi)
• Lower range value (LRV) = 0 bar (0 psi)
• Upper range value (URV) = 5 bar (75 psi)

Cerabar PMP23 IO-Link About this document
Endress+Hauser 7
TD = URL
|URV - LRV|
In this example, the TD is 2:1. This span is based on the zero point.
1.6 Registered trademarks
is a registered trademark of the IO-Link Consortium.

Basic safety instructions Cerabar PMP23 IO-Link
8 Endress+Hauser
2 Basic safety instructions
2.1 Requirements concerning the staff
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists: must have a relevant qualification for this specific
function and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the
instructions in the Operating Instructions and supplementary documentation as well as
in the certificates (depending on the application)
‣Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
‣Being instructed and authorized according to the requirements of the task by the
facility's owner-operator
‣Following the instructions in these Operating Instructions
2.2 Intended use
2.2.1 Application and media
The Cerabar is used to measure absolute and gauge pressure in gases, vapors and liquids.
The process-wetted materials of the measuring device must have an adequate level of
resistance to the media.
The measuring device may be used for the following measurements (process variables)
• in compliance with the limit values specified under "Technical data"
• in compliance with the conditions that are listed in this manual.
Measured process variable
Gauge pressure or absolute pressure
Calculated process variable
Pressure
2.2.2 Incorrect use
The manufacturer is not liable for damage caused by using the device incorrectly or for
purposes for which it was not intended.
Clarification of borderline cases:
‣With regard to special fluids and media used for cleaning, Endress+Hauser will be
happy to assist in clarifying the corrosion-resistant properties of wetted materials but
gives no guarantee or warranty as to the suitability of the materials.
2.2.3 Residual risks
When in operation, the housing may reach a temperature close to the process
temperature.
Danger of burns from contact with surfaces!
‣For elevated process temperatures, ensure protection against contact to prevent burns.

Cerabar PMP23 IO-Link Basic safety instructions
Endress+Hauser 9
2.3 Workplace safety
When working on and with the device:
‣Wear the required personal protective equipment as per national regulations.
‣Switch off the supply voltage before connecting the device.
2.4 Operational safety
Risk of injury!
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Hazardous area
To eliminate the risk of danger to persons or the facility when the device is used in the
approval-related area (e.g. pressure equipment safety):
‣Check the nameplate to verify if the device ordered can be put to its intended use in the
approval-related area.
2.5 Product safety
This device is designed in accordance with good engineering practice to meet state-of-the-
art safety requirements, has been tested, and left the factory in a condition in which it is
safe to operate.
It meets the general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.

Product description Cerabar PMP23 IO-Link
10 Endress+Hauser
3 Product description
3.1 Product design
Overview Item Description
C - 1
A0021987
C - 2
A0027289
C- 1 M12 plug
Housing cap made of plastic
C- 2 M12 plug
IP69: metal housing cap
D
E
A0027227
D
E
Housing
Process connection (sample illustration)
3.2 Operating principle
3.2.1 Calculating the pressure
Devices with metallic process membrane
The process pressure deflects the metal process isolating diaphragm of the sensor and a fill
fluid transfers the pressure to a Wheatstone bridge (semiconductor technology). The
pressure-dependent change in the bridge output voltage is measured and evaluated.

Cerabar PMP23 IO-Link Incoming acceptance and product identification
Endress+Hauser 11
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
A0028673
DELIVERY NOTE
1 = 2
A0016870
Is the order code on the delivery note (1) identical to the order code on
the product sticker (2)?
A0022100
A0028673
A0022103
Are the goods undamaged?
A0028673
DELIVERY NOTE
A0022105
Do the data on the nameplate correspond to the order specifications and
the delivery note?
If one of these conditions does not apply, please contact your
Endress+Hauser sales office.

Incoming acceptance and product identification Cerabar PMP23 IO-Link
12 Endress+Hauser
4.2 Product identification
The measuring device can be identified in the following ways:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
• Enter serial number from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): all the information about the measuring device is
displayed.
For an overview of the technical documentation provided, enter the serial number from
the nameplates in W@M Device Viewer (www.endress.com/deviceviewer)
4.2.1 Manufacturer address
Endress+Hauser SE+Co. KG
Hauptstraße 1
79689 Maulburg, Germany
Place of manufacture: See nameplate.
4.2.2 Nameplate
Ser. no.:
Ord. cd.:
Ext. ord. cd.:
D-79689 Maulburg
Made in Germany,
Cerabar
5
1
2
3
4
Date:
TAG:
A0024456
1 Manufacturer address
2 Device name
3 Order number
4 Serial number
5 Extended order number
4.3 Storage and transport
4.3.1 Storage conditions
Use original packaging.
Store the measuring device in clean and dry conditions and protect from damage caused by
shocks (EN 837-2).
Storage temperature range
–40 to +85 °C (–40 to +185 °F)

Cerabar PMP23 IO-Link Incoming acceptance and product identification
Endress+Hauser 13
4.3.2 Transporting the product to the measuring point
LWARNING
Incorrect transport!
Housing and diaphragm may become damaged, and there is a risk of injury!
‣Transport the measuring device to the measuring point in its original packaging or by
the process connection.

Mounting Cerabar PMP23 IO-Link
14 Endress+Hauser
5 Mounting
5.1 Installation conditions
• Moisture must not penetrate the housing when mounting the device, establishing the
electrical connection and during operation.
• For M12 plug made of metal: Do not remove the protection cap (only in IP69) of M12
plug connection until shortly before electrical connection.
• Do not clean or touch process isolating diaphragms with hard and/or pointed objects.
• Do not remove process isolating diaphragm protection until shortly before installation.
• Always tighten the cable entry firmly.
• Point the cable and connector downwards where possible to prevent moisture from
entering (e.g. rain or condensation water).
• Protect housing against impact.
• For devices with gauge pressure sensor, the following applies:
NOTICE
If a heated device is cooled in the course of a cleaning process (by cold water, for
example), a vacuum develops for a short time causing moisture to penetrate the
sensor via the pressure compensation element (1).
Device could be destroyed!
‣In the event of this happening, mount the device in such a way that the pressure
compensation element (1) is pointing downwards at an angle or to the side, if possible.
1
1
1
1
A0022252
5.2 Influence of orientation
Any orientation is possible. However, the orientation may cause a zero point shift, i.e. the
measured value does not show zero when the vessel is empty or partially full.
C
AB
A0024708
PMP23
Process membrane axis is
horizontal (A)
Process membrane pointing
upwards (B)
Process membrane pointing
downwards (C)
Calibration position, no effect Up to +4 mbar (+0.058 psi) Up to –4 mbar (–0.058 psi)

Cerabar PMP23 IO-Link Mounting
Endress+Hauser 15
5.3 Mounting location
5.3.1 Pressure measurement
Pressure measurement in gases
Mount the device with shutoff device above the tapping point so that any condensate can
flow into the process.
1
2
A0021904
1 Device
2 Shutoff device
Pressure measurement in vapors
For pressure measurement in vapors, use a siphon. The siphon reduces the temperature to
almost ambient temperature. Mount the device with a shutoff device at the same height as
the tapping point.
Advantage:
only minor/negligible heat effects on the device.
Note the max. permitted ambient temperature of the transmitter!
1
2
3
A0024395
1 Device
2 Shutoff device
3 Siphon
Pressure measurement in liquids
Mount the device with a shutoff device at the same height as the tapping point.

Mounting Cerabar PMP23 IO-Link
16 Endress+Hauser
1
2
A0024399
1 Device
2 Shutoff device
5.3.2 Level measurement
• Always install the device below the lowest measuring point.
• Do not install the device at the following positions:
• in the filling curtain
• in the tank outlet
• in the suction area of a pump
• at a point in the tank which could be affected by pressure pulses from the agitator.
A0024405
5.4 Mounting the profiled seal for the universal process
adapter
For details on mounting, see KA00096F/00/A3.
5.5 Post-mounting check
• Is the device undamaged (visual inspection)?
• Does the device comply with the measuring point specifications?
• Process temperature
• Process pressure
• Ambient temperature
• Measuring range
• Are the measuring point identification and labeling correct (visual inspection)?
• Is the device adequately protected against precipitation and direct sunlight?
• Are the securing screws firmly tightened?
• Is the pressure compensation element pointing downwards at an angle or to the side?
• To prevent the penetration of moisture: are the connecting cables/plugs pointing
downwards?

Cerabar PMP23 IO-Link Electrical connection
Endress+Hauser 17
6 Electrical connection
6.1 Connecting the measuring unit
6.1.1 Terminal assignment
LWARNING
Risk of injury from the uncontrolled activation of processes!
‣Switch off the supply voltage before connecting the device.
‣Make sure that downstream processes are not started unintentionally.
LWARNING
An incorrect connection compromises electrical safety!
‣A suitable circuit breaker must be provided for the device in accordance with IEC/EN
61010.
‣The device must be operated with a 500 mA fine-wire fuse (slow-blow).
‣Protective circuits against reverse polarity are integrated.
NOTICE
Damage to analog input of PLC resulting from incorrect connection
‣Do not connect the active PNP switch output of the device to the 4 to 20 mA input of a
PLC.
Connect the device in the following order:
1. Check that the supply voltage corresponds to the supply voltage indicated on the
nameplate.
2. Connect the device as indicated in the following diagram.
Switch on the supply voltage.
Device M12 plug
PMP23
C/Q
L–
L+
21
34SIO
IO-Link
A0034006
1 Supply voltage +
2 4-20 mA
3 Supply voltage -
4 C/Q (IO-Link communication or SIO mode)
6.1.2 Supply voltage
Electronic version Supply voltage
IO-Link 10 to 30 V DC
IO-Link communication is guaranteed only if the supply voltage is at least 18 V.
6.1.3 Current consumption and alarm signal
Electronic version Current consumption Alarm signal 1)
IO-Link Maximum current consumption: ≤ 300 mA
1) For MAX alarm (factory setting)

Electrical connection Cerabar PMP23 IO-Link
18 Endress+Hauser
6.2 Connection data
6.2.1 Relay switching capacity
• Switch state ON: Ia ≤ 200 mA 1); Switch state OFF: Ia ≤1 mA
• Switch cycles: >10,000,000
• Voltage drop PNP: ≤2 V
• Overload protection: Automatic load testing of switching current;
• Max. capacitance load: 1 μF at max. supply voltage (without resistive load)
• Max. cycle duration: 0.5 s; min. ton: 40 μs
• Periodic disconnection from protective circuit in the event of overcurrent (f = 2 Hz) and
"F804" displayed
6.2.2 Load (for 4 to 20 mA devices)
In order to guarantee sufficient terminal voltage, a maximum load resistance RL (including
line resistance) must not be exceeded depending on the supply voltage UB of the supply
unit.
[ ]W
20 30
10
0
1022
587
152
U
[V]
1
2
R
R
L
L
max
max
£-U 6.5V
23mA
B
B
A0031107
1 Power supply 10 to 30 V DC
2 RLmax maximum load resistance
UBSupply voltage
If load is too great:
• Failure current is indicated and "S803" displayed (indication: MIN alarm current)
• Periodic checking to establish if it is possible to quit fault state
• In order to guarantee sufficient terminal voltage, a maximum load resistance RL
(including line resistance) must not be exceeded depending on the supply voltage UB of
the supply unit.
6.3 Post-connection check
• Are the device or cables undamaged (visual check)?
• Do the cables used comply with the requirements?
• Are the mounted cables relieved of tension?
• Are all cable glands installed, securely tightened and leak-tight?
• Does the supply voltage match the specifications on the nameplate?
• Is the terminal assignment correct ?
• If required: has protective ground connection been established?
1) Deviating from the IO-Link standard, larger currents are supported.

Cerabar PMP23 IO-Link Operation options
Endress+Hauser 19
7 Operation options
7.1 Operation with operating menu
7.1.1 IO-Link
IO-Link information
IO-Link is a point-to-point connection for communication between the measuring device
and an IO-Link master. The measuring device features an IO-Link communication interface
type 2 with a second IO function on pin 4. This requires an IO-Link-compatible assembly
(IO-Link master) for operation. The IO-Link communication interface enables direct access
to the process and diagnostic data. It also provides the option of configuring the measuring
device while in operation.
Physical layer, the measuring device supports the following features:
• IO-Link specification: Version 1.1
• IO-Link Smart Sensor Profile 2nd Edition
• SIO mode: Yes
• Speed: COM2; 38.4 kBaud
• Minimum cycle time: 2.5 msec.
• Process data width:
• without Smart Sensor Profile: 32 bit
• with Smart Sensor Profile: 48 bit (float32 + 14-bit vendor spec. + 2 bits SSC)
• IO-Link data storage: Yes
• Block configuration: Yes
IO-Link download
http://www.endress.com/download
• Select "Software" as the media type
• Select "Device Driver" as the software type
Select IO-Link (IODD)
• In the "Text Search" field enter the device name.
https://ioddfinder.io-link.com/
Search by
• Manufacturer
• Article number
• Product type
7.1.2 Structure of the operating menu
The menu structure has been implemented according to VDMA 24574-1 and
complemented by Endress+Hauser-specific menu items.
For an overview of the operating menu, see the →  43

System integration Cerabar PMP23 IO-Link
20 Endress+Hauser
8 System integration
8.1 Process data
The measuring device has a current output and a switch output. The status of the switch
output is transmitted in the form of process data via IO-Link.
• In the SIO mode, switch output 1 is switched at pin 4 of the M12 plug. In the IO-Link
communication mode, this pin is reserved exclusively for communication.
• The current output at pin 2 of the M12 plug is always active or can be optionally
deactivated via IO-Link.
8.1.1 Without Smart Sensor Profile
The device's process data are transmitted cyclically in 32-bit chunks.
Bit 0 (LSB) 1 ... 28 29 (MSB) 30 31
Measuring device Pressure value OU1 res.
Bit 31 is reserved. Bit 30 provides the status of the switch output.
Here, 1 or DC 24 V corresponds to the logical "closed" state on the switch output. The
remaining 30 bits contain the analog raw measured value of the device. This value has yet
to be scaled by the target system to the nominal operating range of the existing measuring
device.
Bit Process value Value range
30 OU1 0 = open
1 = closed
0 to 29 Raw value Int30
The decimal separator must be set with a gradient. The gradients depend on the unit in
question. The following units are available:
• bar: 0.0001
• kPa: 0.01
• MPa: 0.00001
• psi: 0.001
Examples:
Pressure value Transmitted Scaled with gradient
–320 mbar –3 200 –0.32
22 bar 220 000 22
133 Pa 13 300 133
665 psi 665 000 665
399.5 bar 3 995 000 399.5
8.1.2 With Smart Sensor Profile
The measuring device's process data are transmitted cyclically as per SSP 4.3.1