Enduraplas LAND CHAMP SLC050FG8GR User manual

LAND CHAMP ™
OWNER’S MANUAL
Version 2.1 Copyright © Enduraplas. All Rights Reserved.
Product Codes:
SLC050FG8GR, SLC100FG8GR, SLC200FG8GR,
SLC050FG8GRS, SLC100FG8GRS, SLC200FG8GRS
SLC100FG8GR
SLC200FG8GR

2Land Champ™
English
CONTENTS
INTRODUCTION 3
WARNINGS 4 & 5
GETTING STARTED 6 - 21
CALIBRATING 22 & 23
MAINTAINING 24 & 25
CLEANING 26 & 27
WINTERIZING 28
TROUBLESHOOTING 29 & 30
WARRANTY 31 -35
PARTS BREAKDOWNS 36 - 51
!

3Version 2.1
English
INTRODUCTION
Congratulations! You now own an Enduraplas sprayer. Dura-
ble design and construction assure you a lifetime of extreme
performance. No sprayer is tougher. No sprayer will last lon-
ger.
Take a look through this owner’s manual to learn how the
pros use their Enduraplas sprayer.
Discover More Helpful Tips:
blog.enduraplas.com/spraying
Watch Instruction Videos:
www.youtube.com/enduraplas
Order Genuine Enduraplas Parts & Accessories:
parts.enduraplas.com

4Land Champ™
English
WARNINGS
1. When connecting this sprayer to your UTV (or vehicle),
ensure that you have read the UTV’s Owner’s Manual
and that you comply with all the weight restrictions as
specified by the UTV’s manufacturer, as overloading can
cause injury or death. Remember that 1 gallon of water
weighs 8.33 pounds.
2. To ensure your own safety and that of others, you must
comply with all relevant environmental, work place health,
safety legislation and codes of practice.
3. Select and wear appropriate Personal Protection
Equipment in accordance with the label of the product
you intend to use.
4. Care should be taken when spraying in windy conditions
as spray drift may contaminate the air and may aect the
operator or damage adjacent non-target vegetation. It is
recommended that a speed of 6mph is not exceeded.
5. Once the spraying operation has been completed,
decontaminate the spray tank and spray accessories.
Dispose of tank rinsing’s in compliance with current
environmental, work place health and safety regulations.
6. Personal Protection Equipment must still be worn while
decontaminating your sprayer as per warning 3 above.
7. Improper or careless use of this sprayer can cause serious
injury. Minors should never be allowed to use this sprayer.
This sprayer should not be used when bystanders or
animals are in the area. This sprayer should never be used
while children are in the area.
8. Never leave the sprayer unattended without turning o
the pump, relieving the line pressure, and flushing the
sprayer of any harmful chemicals.
9. You must be in good mental health to operate this sprayer
and not be under the influence of alcohol or any drugs
!

5Version 2.1
English
that could impair your vision, physical strength, dexterity,
judgment, or other mental capacity.
10. No modifications and/or alterations may be made to this
sprayer. Any such modifications not only void the sprayer
Discover More Helpful Tips:
blog.enduraplas.com/spraying
Watch Instruction Videos:
www.youtube.com/enduraplas
1. Wear tightly fitted clothing while connecting and
disconnecting your sprayer.
2. Check to make sure all PTO shields and guards are in
place when you are spraying.
3. Disengage the PTO, shut o the tractor, and remove the
keys before connecting or disconnecting your PTO pump.
4. Do not reach over the back of the tractor to adjust the
PTO or throttle.
5. Never step over a revolving PTO shaft even if shielded.
PTO WARNINGS !

6Land Champ™
English
1) Connect controller bracket using four
1/4” x 3/4” bolts, four 1/4” flat washers,
and four 1/4” lock washers.
2) Tighten bolts securely.
3) Lubricate and insert hose into
provided grommet in tank.
Mounting the Controls
GETTING STARTED

7Version 2.1
English
1) Attach the 2 brackets to the tank
using two 3/8” x 3/4” bolts, two 3/8” flat
washers, and two 3/8” lock washers.
2) Bolt hose clips onto brackets with two
pan head screws and nuts.
3) Wrap hose around and insert gun into
clips.
Mounting the Hose/Gun Clips
GETTING STARTED

8Land Champ™
English
1) Align Tractor
Back the tractor up to the sprayer
aligning tractor hitch points with the arms
at the height of the two lower mounting
points on sprayer.
2) Insert Arm Pins
Hook the two lower hitch arms to the
mounting point pins on the sprayer, then
secure with lock pin.
3) Insert Pin to Top Link
Hook up top three point arm on tractor
to the third (top) mounting point on the
sprayer and insert the lock pin.
4) Connect Pump
Align and connect the pump to the PTO
shaft and hook on the torque chain to
keep the pump from turning along with
the PTO shaft.
Hitching to a Tractor
GETTING STARTED

9Version 2.1
English
5) Test
Using the tractors hydraulics, lift your
sprayer o the ground to insure it is
secured properly.
Discover More Helpful Tips:
blog.enduraplas.com/spraying
Watch Instruction Videos:
www.youtube.com/enduraplas
Hitching to a Tractor
GETTING STARTED

10 Land Champ™
English
1) To install boom brackets to the spray-
er, insert the 3/8” x 1” bolts through the
bracket and place plastic washers over
bolts to hold them in place.
2) Connect the brackets by sliding the
3/8” x 1” bolts through the C-bracket on
unit and install 3/8” washer and 3/8” lock
nuts loosely.
Mounting Your Boom
3) To install your boom to the brackets,
loosen the carriage bolts on the boom
(leaving nuts and washers on bolts).
Align carriage bolts with quick attach
brackets and slide them into the brack-
et slots, then lower the boom down to
desired height.
4) When the boom is set to desired
height, tighten the hardware, making
sure the square neck on the carriage
bolt is fully inserted through the slot.
GETTING STARTED

11Version 2.1
English
5) Once the boom is secure, tighten the
hardware on the boom brackets to make
sure they are also secure.
6) Take the feed hoses from boom and
connect to male brass hose fittings on
spray unit. Hook hoses up to the appro-
priate section control; 12’, 20’ and 30’
booms have 3 hose hookups and boom-
less nozzle has 2 hose hookups.
Mounting Your Boom
7) If you got the 30’ boom extensions,
once the 20’ boom is mounted, bolt on
the extensions to the boom ends.
8) Then, hook up the hoses using the
brass threaded connectors.
GETTING STARTED

12 Land Champ™
English
9) If you got the 30’ boomless nozzle kit,
bolt the boomless nozzle bracket to the
back of sprayer frame using provided
bolts.
10) Hook up hoses from boomless noz-
zle to brass ports on back of sprayer.
Mounting Your Boomless Nozzle
GETTING STARTED
Please refer to the spray boom owner’s manual for boom
assembly and parts breakdown.
Discover More Helpful Tips:
blog.enduraplas.com/spraying
Watch Instruction Videos:
www.youtube.com/enduraplas
GETTING STARTED

13Version 2.1
English
1) Fill your tank 1/4 full with water.
2) Ensure three way valve is in open
position allowing liquid to flow from
large tank to pump. Valve needs to be in
forward position (handle facing tractor).
4) If liquid is not flowing into tank
through the return line, there may be
an airlock in the line and you may need
to prime the pump. Remove plug from
back of pump, allowing air out of the line.
When liquid starts to flow, reinsert plug
and pump should be primed.
Setting Up Sprayer
3) Before starting PTO, make sure
the pressure regulator is fully open
(counterclockwise) to avoid premature
wear or damage to the pump. This will
allow liquid to flow from pump and
return back to tank. Pump should prime
automatically.
GETTING STARTED

14 Land Champ™
English
Setting Up Sprayer
5) Once pump is running and liquid is
recirculating back into the tank, tighten
knob (clockwise) to desired pressure.
This will lessen the liquid flow from the
tank and redirect to the spray boom.
6) Once you have set your desired pres-
sure, test the spray boom by turning on
Right, Center, and Left section controls.
When controls are in the up position, the
sprayer boom should be engaged.
7) When using the hose wrap, make sure
the valve to the hose wrap is open.
GETTING STARTED

15Version 2.1
English
1) Place Hose Reel on Tank opposite of
lid end.
2) Insert four 3/8” x 3/4” bolts with 3/8”
flat washers and lock washers through
hose reel into inserts in tank. Secure
tightly.
3) Run 3/8” hose from the hose reel to
the black handled valve coming out of
the top of the three way valve bank,
connect and tighten clamp.
Optional Hose Reel
GETTING STARTED

16 Land Champ™
English
Optional Electric Solenoid Kit
2) Mount contoller in cab; make sure
this is mounted where it will not obstruct
operators view.
3) Connect the wire harness from the
controller to the 3 electric valve banks
on sprayer by plugging in the matching
ends to the valves.
4) Connect white pressure line from con-
troller to valve bank with provided con-
nectors. Make sure white pressure hose
is bottomed out all the way into connec-
tor fittings before tightening connector.
1) If you ordered your sprayer with the
optional electric solenoid controls, mount
solenoid kit to side of tank using two 1/4”
x 3/4” bolts and 1/4” flat and lock wash-
ers.
GETTING STARTED

17Version 2.1
English
5) This unit comes with power wires that
you will either need to add gator clips
to or wire directly to a power source. If
gator clips are used, connect to battery;
red to positive and black to negative.
6) Turn on vehicle key to power up
controller and turn on master switch on
controller.
Optional Electric Solenoid Kit
8) Fill tank 1/4 full with water.
7) To make sure your solenoids have
power, switch the 3 valve controls on
and o listening for the valves to click
open and shut on the sprayer.
GETTING STARTED

18 Land Champ™
English
10) Once you have reached desired
pressure, test the spray boom by turning
on the Left, Center, and Right control
switches.
9) With sprayer pump running, increase
your pressure to desired amount by
holding up on pressure control toggle
switch; hold up for a couple seconds,
then release.
Optional Electric Solenoid Kit
GETTING STARTED

19Version 2.1
English
Optional Hand Wash Tank
2) Screw both mounting brackets into
the tank inserts and tighten.
3) Connect hand wash tank by sliding
tank into cradle brackets and inserting
the clip mounts through the tank. When
the tank is in position, flip the clip lock to
secure.
4) Wrap threads on spigot with sealant
tape and thread spigot into tank.
1) Insert hand wash clip bolts into the
holes on the brackets and tighten bolts.
GETTING STARTED

20 Land Champ™
English
Optional Storage Stand
2) Lubricate all round sections on the
stand.
3) Insert one end of the stand into the
first bracket that was loosely connected.
4) Slide the second bracket onto the
other end of the stand and mount it to
the sprayer frame. Then tighten all bolts.
Repeat on the other side of the frame to
complete stand.
1) Loosely connect the first stand bracket
to the sprayer stand with two bolts.
GETTING STARTED