Eneo HDB-2080M2810IR D User manual

EN
Quick Installation Guide
1/3”HDcctv Camera, 3D-DNR,
Day&Night, 1920x1080, 2.8-
10mm, RS-485, infrared,
12/24V
HDB-2080M2810IR D

Safety Precaution
03
FULL-HD MEGA-PIXEL CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

FULL-HD MEGA-PIXEL CAMERA
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
04

FULL-HD MEGA-PIXEL CAMERA
Contents
Safety Precaution
p.03~04
Contents
p.05
Features
p.06~07
Composition
p.07
Dimensions
p.08
Part Names
p.09
Installation Instructions
p.10~12
Operating Instructions
p.13~29
Specifications
p.30~31
05

FULL-HD MEGA-PIXEL CAMERA
Features
Key Features
06
• Full HD, 2Mega Pixel EX-SDI CAMERA, 1920x1080(30p/25p)
• Extended long reach HD Solution
• Real time True WDR(Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• Built-in f=2.8~10mm F1.4, Mega-pixel DC Auto Iris vari-focal lens
• Dual Filter Switcher
• Day & Night Simulation for easy focus adjustment
• Various Zooming Technologies
- Pointing Zoom (which enables the programmable zooming at any area)
- Preset Zoom
- Flex Zoom
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
• Motion Detection, Privacy Mask, Defog, Sens-up(~x32), D-WDR,
H/V/HV Flip, D-Zoom(~8x), Lens Shade Compensation, BLC/HLC,
Pixel Defect Compensation, Title Set
• EX-SDI or HD-SDI switchable
• Top performance at low light sensitivity (Sens-up On)
• OSD menu & CVBS Video output BNC for easy installation & maintenance.
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• Remote control via RS-485 (Pelco-D/P)
• Quick Firmware update via RS-485
• Operable up to -50ºC
• External Zoom & Focus adjustment
• Built-in 40pcs LEDs
• LED ON/OFF Control
• Dual Window
• Built-in Heating function
• One-touch 3-Axis locking bracket, Easy Installation Pad
• IP67 protection

FULL-HD MEGA-PIXEL CAMERA
General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With Intelligent Focus Indicator and FOCUS ASSIST menu,
- Offers easy adjustment of Focus
- Eliminates the mistake of the erratic focus adjustment
• With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front
of you by Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
07
Composition
Features
Camera
Mounting Template
Operating
Instruction
Torque Wrench:
3mm (1pc)
Video Sub-out
Cable (1pc)
Assembly Screw:
4 x 14mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Easy
Bracket
Cable Signal
Sticker
Wiring Connector:
(1pc)

FULL-HD MEGA-PIXEL CAMERA
Dimensions
(unit : mm)
08
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken the cable is NOT to be damaged, kinked or exposed
in the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun
or spot light.
CAUTION
267
108
87.30
100
86.40
75.90
80
190

Part Names
FULL-HD MEGA-PIXEL CAMERA
09
DUAL WINDOW
POWER CABLE
SUNSHIELD BOLT
REAR VIEW
SUNSHIELD
FRONT CASE
EASY
BRACKET
OSD Setup
CONTROL COVER
BRACKET
REAR CASE
FOCUS ZOOM
LOCK/UNLOCK
SCREW
■Adjustment of viewing angle with a bracket
Torque
wrench
Lock/Unlock
Screw

Installation Instructions
FULL-HD MEGA-PIXEL CAMERA
10
Torque Wrench
Assembly Screw
: 4x14mm
Mounting Screw
: 4x30mm
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws (4x30mm). Skip this step when an easy bracket is not installed.
3. Route the Power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x14mm).
5. Set the camera’s viewing angle and adjust zoom/focus of lens by using the torque
wrench.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
REAR VIEW
1
2
3
4
Cable exit

Installation Instructions
FULL-HD MEGA-PIXEL CAMERA
11
Pan & Tilt adjustments
Zoom & Focus adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
• Turn the Focus gear to “N”(Near) or “∞”(Far)
until the sharpest focus is made.
• To widen the viewing angle, turn the Zoom to
“W”(Wide) and to obtain a closer view, turn it
to “T”(Tele)
Use the torque wrench supplied.
• Unlock the screw on the camera bracket through using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
88°90°
±90°
•on the wall •on the ceiling

Installation Instructions
FULL-HD MEGA-PIXEL CAMERA
12
VIDEO (BNC)
AC24V/GND (Black wire)
AC24V/DC12V (Red wire)
RTX-/RS485 (Gray wire)
RTX+/RS485 (White wire)
Power Supply Connections
Make sure the power is removed before the installation.
Camera can work with either 24AC or 12VDC, dual voltage power .
Primary and secondary grounds are completely isolated to avoid the possible
ground-loop problems
In case that HD-SDI/EX-SDI Inputs are not supported in Monitor, please use
HD-SDI/EX-SDI Converter to connect HD-SDI/EX-SDI cable with Monitor
Some computer monitors or TVs may not support 30p/25p.
In this case, HD-SDI/EX-SDI DVR which can convert the frame rate to 60p/50p
is highly recommended.
Please check Specification of Monitor before installation.
※ Attach the Signal Assignment Sticker
in a visible spot for wiring reference.

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
13
Setup menu can be accessed and controlled by OSD control joy stick on the
side of camera unit.
Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.
4) ‘☟’denotes the long press down straightly for about 2 seconds
(*) Works only when OSD menu is inactive.
Description of the D-ZOOM* adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
Using OSD controller
Cover Open
Video Sub-out
Connector
OSD Control
Joy Stick
SUB-OUT
Video format
Switch

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
14
Set the video format according to system,
EX-SDI or HD-SDI
DVR
350M+ via RG59u or 5C2V cable
350M+ via
RG59u or 5C2V
cable
350M+ via RG59u or 5C2V cable
1M~120M via RG59u or 5C2V cable
1M~120M
via
RG59u or
5C2V cable
1M~120M
via
RG59u or
5C2V cable
1M~120M
via
RG59u or
5C2V cable
DVR
(HD-SDI)
Camera
(HD-SDI)
Camera
(HD-SDI)
Camera
Camera
HDA-3000E HDA-3000E
HDA-3000E
DVR
(HD-SDI)
DVR
(HD-SDI)

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
OSD menu Startup
Press ‘●’(OSD menu Joy stick key) down for about 2 seconds to access the
setup menu mode.
MENU V5.xx
1. EXPOSURE
2. LENS
3. FOCUS ASSIST
4. SCENE ENHANCE
5. 3D-NR
6. DAY/NIGHT
7. PICT ADJUST
8. SPECIAL
9. SYSTEM
A. EXIT
NORMAL
MID
EXT
SAVE&EXIT
DC
Direct Control menu
MAIN DEFAULT DESCRIPTION
LENS Sets Lens types.
DC
FOCUS ASSIST Sets FOCUS
-
EXPOSURE
Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and
MOTION DEBLUR.
-
SCENE
ENHANCE
NORMAL SCENE ENHANCE provides the several ways to enhance the video
in the various environments with the settings in NORMAL, WDR,
D-WDR, BLC and HLC.
15
Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA PICT ADJUST
Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET,
DISPLAY, DEFOG, POINTING ZOOM
SPECIAL
Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and
FACTORY DEFAULT
SYSTEM
Sets 3DNR level. LOW, MID, HIGH
Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N.
Setting EXT mode for cameras with IR-LED, AUTO mode for none
IR-LED camera types.
DAY/NIGHT
EXT
or
AUTO
3D-NR MID

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
• AUTO: Optimizes the video level by controlling the iris and the shutter speed
automatically.
• MANUAL: Iris and Shutter can be set to fix.
• Flickerless : Reduces the flicker in video when US(60Hz)/EU(50Hz) mode is
used in 50Hz/60Hz fluorescent lighting respectively.
1. EXPOSURE
: Can set EXPOSURE MODE to AUTO, MANUAL and Flickerless. MANUAL
and Flickerless modes disable SENS-UP and MOTION BLUR functions.
1-1. SHUTTER (default: AUTO)
: Adjusts the brightness of video(0~20).
1-2. BRIGHTNESS (default: 10)
|:::::::|::::::| 10
|:::::::|::::::| 12
• AUTO: SENS-UP is enabled or disabled automatically by the scene brightness.
Higher SENS-UP can get the brighter video but the slower frame rates with motion
blur and more white pixels. If set to AUTO, maximum integration limit for SENS-UP
can be set to x2, x4, X8, x16, X32 in SENS-UP menu.
• OFF: Disables SENS-UP.
: The brighter video can be obtained by increasing the exposure time in the night
with SENS-UP. SENS-UP is the maximum integrations of frame by DSS (Digital
Slow Shutter) in the low light.
2-3. SENS-UP (default: AUTO)
: AGC(0~20) amplifies the video gain for brighter video but noise and white pixel
accordingly. AGC level less than 10 disables AUTO in DAY/NIGHT.
2-4. AGC (default: 12)
16
EXPOSURE
SHUTTER
BRIGHTNESS
SENS-UP
AGC
RETURN
AUTO
OFF
RET
SAVE & EXIT – Exits the menu after saving the parameters.
EXIT – Exits the menu without saving the menu.
EXIT

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
17
FOCUS ASSIST
DN DWELL
POP ON FOCUS
RETURN
5s
OFF
RET
FOCUSING STATUS
• DN DWELL (5s) : ICR switcher
switches DAY & NIGHT at the
interval of D/N DWELL to help the
EXACT NIDDLE focus at DAY and
NIGHT mode.
Further simulations are performed
internally during switching.
DC
MODE
RETURN
INDOOR
RET
• INDOOR: Optimized of indoor environment.
• OUTDOOR: Optimized of outdoor environment.
• DEBLUR: It enables to reduce the blur in
a certain indoor environment.
Noise or color rolling can increase.
• NORMAL: Optimized of indoor environment.
• DEBLUR: It enables to reduce the blur in
a certain indoor environment.
Noise or color rolling can increase.
2. LENS
MANUAL
MODE
RETURN
NORMAL
RET
: Selects lens mode according to installation
place. INDOOR or DEBLUR for indoor
installation according to environment.
2-1. DC (default: INDOOR)
: Horizontal wave or bar may be seen when
MANUAL is selected and the camera
is working under florescent or similar lights.
2-2. MANUAL (default: NORMAL)
Lens can be selected either DC or MANUAL lens.
Lens MUST be set to DC for the best image when DC iris lens is installed
3. FOCUS ASSIST
FOCUS ASSIST menu is the unique and patented feature that prevents from
the wrong focus and helps the EXACT NEEDLE focus by simulating DAY &
NIGHT conditions. Set zoom first and adjust focus to get NEEDLE FOCUS while
switching at DAY & NIGHT.
Usually cameras are installed in the day time and they often become OUT OF
FOCUS at night time and IN FOCUS again at next day time.
This problem can occur at any cameras regardless of types or manufacturers.

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
18
• POP ON FOCUS (OFF) :
ON zooms in the center of picture at 2X for better focusing.
• FOCUSING STATUS (ON) : Shows how exactly focus is set. When blue bar
doesn’t show up, try the lens focus to NEAR and FAR. The maximum blue bar
indicates the best focusing position.
4-1. NORMAL (default)
4-2. WDR
4-3. D-WDR
4. SCENE ENHANCE
: Optimized for the normal indoor and outdoor in the good lighting condition.
: Improves the visibility for the high bright area and the dark area by the double
captures of image with LONG and SHORT exposures. With WDR ON, the
frame rate becomes half by the double captures. WDR level can be selected
from LOW, MID and HIGH. Care should be taken to select this mode because
video may lose its quality in some environments by the over compensation.
※CVBS video signal:Connecting 2nd video to CVBS port disables WDR function
temporary. It should be considered when installer adjusts the video with
installation monitor via CVBS video signal.
: Improves the visibility by compensating the video gain for the dark area.
Noise can increase in the dark area accordingly.
3D-NR is a very sophisticated and powerful time-based noise reduction technology
by monitoring the noise for the several video frames and defining and eliminating
them consecutively at low light. Higher setting reduces noise much more but results
in losing the sharpness and the tail effect or the motion blur for the fast moving
target at low light.
4-4. BLC
4-5. HLC
5. 3D-NR
: Cuts out the highlight area with black mask and excludes it from compensation.
Lower HLC LEVEL cut out video from the lower level.
: Improves the visibility for the dark object by the bright back light.
Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position can be set
by H-POS, V-POS, H-SIZE and V-SIZE.

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
19
: DAY or NIGHT is determined by the built-in light photo sensor.
Camera with IR LED must be set to EXT.
DAY/NIGHT is used to control the setting during day-time and night-time operation.
Select the mode according to the light condition and the camera types.
SMART IR can be set to reduce the saturation by the strong IR illumination in the
night in any menu. Setting SMART IR in any menu is identically applied to other
menu. Zero(0) turns off SMART IR and High setting avoids the saturation strongly
but the corners will be darker accordingly.IR LED Control(AUTO/OFF) is available
with IR LED model only. If IR LED is set to OFF, IR LED will be turned OFF but DAY
or NIGHT is still determined by the built-in light photo sensor.
6-1. EXT
6-2. AUTO
6. DAY / NIGHT
: Used when DAY or NIGHT is determined by light level through the lens and
DAY from/to NIGHT is switched automatically by the scene brightness.
D↔N THRESHOLD, D↔N DELY and SMART IR can be set in the menu.
When EXPOSURE>AGC is less than 10, DAY/NIGHT AUTO is disabled and
forcibly switches to ___(DAY) to avoid the malfunction. EXT, B/W (NIGHT)
and COLOR(DAY) is independent on AGC level. When EXTERNAL IR LED
is used with NON IR LED model, please set to IR LED MODE ON.
• D↔N GAP (0~15):
Sets the gap level switching from
/to DAY(color) or NIGHT(B/W).
• D↔N THRESHOLD (0~20):
Sets the threshold level switching from/to DAY(color) or NIGHT(B/W).
Setting low level makes camera entered NIGHT at lower light level. High level
makes camera exited NIGHT at brighter light level.
• D↔N DELAY (0~60s):
Sets the delay time when the camera
switches from/to DAY(color) or
NIGHT(B/W).
• SMART IR :
SMART IR can be set to reduce the saturation by the strong IR illumination in
the night in any menu of EXT, AUTO and B/W(NIGHT). Setting SMART IR in
DAY/NIGHT AUTO
D<->N THRESHOLD
D<->N GAP
D<->N DELAY
SMART IR
RETURN
5s
RET
|:::::::|::::::| 10
|:::::::|::::::| 10
|:::::::|::::::| 10

Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
20
• ATW: White balance is continuously
working along with the color
temperature changes in the range of
2,000K~8,500K.
: ATW, ATWext, ONE PUSH and MANUAL are available for the white balance
modes.
7-1. WHITE BAL (default: ATW)
PICTURE
WHITE BAL
SHARPNESS
COLOR GAIN
GAMMA
SHADING
RETURN
ATW
0.50
OFF
RET
7. PICT ADJUST
|:::::::|::::::| 10
|:::::::|::::::| 10
: Forcibly removes IR cut filter and switches to B/W regardless of light level.
6-3. B/W(NIGHT)
: Forcibly DAY/NIGHT is disabled and outputs color video.
6-4. COLOR(DAY)
6-5. COLOR D/N
: Forcibly Color mode, optimized for night condition. It is available to recognize
colors of car, people and moving objects even at night. Parameters can be
controllable & programmable according to circumstance. Application for bright
circumstance at night such as downtown, civic area, street, mall and etc.
Conventional COLOR mode in NIGHT COLOR D/N mode in NIGHT
any menu is identically applied to other menu. Zero(0) turns off SMART IR and
high level avoids the saturation strongly but the corners will be darker accordingly.