Eneo HDD-2080Z03IR D User manual

EN
User Manual
1/3” HDcctv Dome, WDR,
Day&Night, 1920x1080, 3-9mm,
3x AF Zoom, Infrared, 12/24V
HDD-2080Z03IR D

Safety Precaution
03
FULL-HD AF-ZOOM CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

Safety Precaution
04
FULL-HD AF ZOOM CAMERA
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

Contents
05
FULL-HD AF ZOOM CAMERA
Safety Precaution
p.03~04
Contents
p.05
Features
p.06~07
Composition
p.07
Dimensions
p.08
Part Names
p.09
Installation Instructions
p.10~13
Operating Instructions
p.14~31
Specifications
p.32~33

Features
Key Features
06
FULL-HD AF ZOOM CAMERA
• Full HD, 2Mega Pixel, EX-SDI CAMERA, 1920x1080(30p/25p)
• Extended long reach HD Solution
• Real time True WDR (Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• Built-in f=3~9mm, F1.2~F2.1 Day&Night zoom lens
(Optical 3x Auto focus zoom / Digital 32x zoom)
• Dual Filter Switcher
• Focusing Status Indicator on Screen
- ★(Blue) Focusing in process
- ★(White) Focusing Completed
• Various Zooming Technologies
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
- Pointing Zoom (which enables the programmable zooming at any area)
- Preset Zoom
• Home Position setting
• Motion Detection, Privacy Mask, Defog, Sens-up(x32), BLC/HLC,
H/V/HV Flip, Motion Deblur, Pixel Defect Compensation, Lens Refresh,
Lens Initialize
• ID / TITLE / ZOOM RATIO DISPLAY
• Enhanced Sensitivity by DSS technology
• EX-SDI or HD-SDI switchable
• Top performance at low light sensitivity (Sens-up On)
• OSD menu & Video sub-out for easy installation & maintenance
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• Remote control via RS-485 (Pelco-D/P)
• Quick Firmware update via RS-485
• 2 High power LEDs
• Flush mount (Optional mounting accessories are choosable)
• Hard Coated Polycarbonate Clear bubble dome
• Built-in 3-Axis Gimbal
• Built-in cooling Fan & Heating function
• IP67 / IK10 Protection

General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front
of you by adopting Auto Focus Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
Features
07
FULL-HD AF ZOOM CAMERA
Composition
Mounting Template
Cable Signal
Sticker
Operating
Instruction
Torque Wrench:
3mm (1pc)
Video Sub-out
Cable (1pc)
Mounting Screw:
4 x 30mm (3pcs)
Plastic Anchor:
6 x 30mm (3pcs)
Dome Camera
Wiring Connector
(1pc)
Connector fixing Screw:
2.5 x 5mm (1pc)

Dimensions
08
FULL-HD AF ZOOM CAMERA
Ø140
119
PCD Ø120
Ø102
Ø140
3-Ø4.2
82
(unit : mm)

Part Names
09
FULL-HD AF ZOOM CAMERA
BUBBLE DOME
3-AXIS GIMBAL
DOME COVER
SAFTY WIRE
FLUSH MOUNT
ZOOM LENS
OSD CONTROL
JOY STICK
POWER CABLE
VIDEO (BNC)
POWER CABLE
[ BOTTOM VIEW ]
POWER SUPPLY
CONNECTOR
POWER
CABLE

Installation Instructions
10
FULL-HD AF ZOOM CAMERA
1. Locate the mounting template at the installation position and drill the ceiling
or wall if needed.
2. Open the dome cover by loosening screws(4x12mm). Use the torque wrench
supplied.
3. Set the camera’s viewing angle.
4. Put the dome cover to the dome base unit and tighten the assembly screws.
- Place the dome base unit on pre-drilled position and fix it through using mounting
screws (4x30mm).
- Route the Power cable to the connecting place.
• Surface mount
• Pole mount adaptor
• Tilted mount
• Wall mount
(Requires additional
Surface mount)
• Tilted junction mount
■ Optional Mounting Accessories
Mounting Screw
(4x30mm)
Plastic Anchor
(6x30mm)
Torque
Wrench

Installation Instructions
11
FULL-HD AF ZOOM CAMERA
■Option 2.
Installation with Surface mount / Tilted mount
■Option 1.
Installation with Flush mount / Tilted Junction mount
3
1
Connector
fixing screw
2
Cable Holder
* Refer to the instruction guide for Tilted Junction mount .
①Cable is unfixed on the Dome base.
②Connect the power cable to their repective connections.
①Cable is unfixed on the Dome base.
②Fix the power supply connector with fixing screw as illustrated.
③Tie up the BNC cable with cable holder.
④Connect the wiring connector to their repective connections.
* Refer to the signal assignment for wiring connection.
CAUTION
• In the case of installation with Flush/ Surface/ Tilted mount,
IP protection rating is not guaranteed.
• If power, Video connectors are exposed to water or rain, separate
protection shield is essential.

• Extreme care should be taken NOT to scratch the bubble dome surface while
the camera installing or adjusting.
•Care should be taken the cable is NOT to be damaged, kinked or exposed in
the hazardous area.
•Tighten enough the dome cover fixing screws so that there should be NO
gap between Lens hood and clear bubble to avoid the light inflow from IR LEDs.
Limit of pan & tilt
1) Pan limit:
Pan is limited to +/- 173°. Do NOT force to rotate the gimbal over the limit to
prevent from the internal damage.
2) Tilt limit:
Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when the
inclination of camera module is 0°, that is, the image is aligned horizontally.
3) Inclination limit (Horizontal image alignment):
Inclination limited to +/- 50° max.
Installation Instructions
12
FULL-HD AF ZOOM CAMERA
CAUTION
25º
90º

Installation Instructions
13
FULL-HD AF ZOOM CAMERA
Power Supply Connections
Make sure the power is removed before the installation.
Camera can work with either 24AC or 12VDC, dual voltage power.
Primary and secondary grounds are completely isolated to avoid the possible
ground-loop problems
VIDEO (BNC)
AC24V/GND (Black wire)
AC24V/DC12V (Red wire)
RTX-/RS485 (Gray wire)
RTX+/RS485 (White wire)
※ Attach the Signal Assignment Sticker
in a visible spot for wiring reference.
In case that HD-SDI/EX-SDI Inputs are not supported in Monitor, please use
HD-SDI/EX-SDI Converter to connect HD-SDI/EX-SDI cable with Monitor
Some computer monitors or TVs may not support 30p/25p.
In this case, HD-SDI/EX-SDI DVR which can convert the frame rate to 60p/50p
is highly recommended.
Please check Specification of Monitor before installation.

OSD control Joy Stick
Video Sub-out
Connector
Using OSD controller
Setup menu can be accessed and controlled by OSD control joy stick on the
side of camera unit.
Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move the
cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.
4) denotes the long press down straightly for about 2 seconds
Operating Instructions
14
FULL-HD AF ZOOM CAMERA
Description of the ZOOM&FOCUS adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
3) ◄: Focus Near
4) ►: Focus Far
Video format
Switch

Operating Instructions
15
FULL-HD AF ZOOM CAMERA
Set the video format according to system,
EX-SDI or HD-SDI
1M~120M via RG59u or 5C2V cable
Camera (HD-SDI) DVR (HD-SDI)
Camera (HD-SDI)
1M~120M via
RG59u or 5C2V
cable 350M+ via RG59u or
5C2V cable
HDA-3000E
(EX-SDI)
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable
DVR (HD-SDI)
Camera (EX-SDI)
350M+ via RG59u or 5C2V cable
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable
DVR (HD-SDI)
350M+ via RG59u or 5C2V cable
Camera (EX-SDI) DVR (EX-SDI)
Camera (HD-SDI) DVR (HD-SDI)
1M~120M via
RG59u or 5C2V
cable
1M~120M via RG59u or
5C2V cable
HDA-3000E
(EX-SDI)
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable

Operating Instructions
16
FULL-HD AF ZOOM CAMERA
Direct Control menu
OSD menu Startup
MAIN DEFAULT DESCRIPTION
ZOOM/FOCUS Sets FOCUS and ZOOM relative fuctions.
-
EXPOSURE
Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and
MOTION DEBLUR.
-
SCENE
ENHANCE
NORMAL SCENE ENHANCE provides the several ways to enhance the video
in the various environments with the settings in NORMAL, WDR,
D-WDR, BLC and HLC.
Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA
PICT ADJUST
Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET,
DISPLAY, DEFOG, POINTING ZOOM
SPECIAL
Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and
FACTORY DEFAULT
SYSTEM
Sets 3DNR level. LOW, MID, HIGH
Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N.
Setting EXT mode for cameras with IR-LED, AUTO mode for none
IR-LED camera types.
DAY/NIGHT
EXT
or
AUTO
3D-NR MID
Press ‘●’(OSD menu Joy stick key) down for about 2 seconds to access the
setup menu mode.
Lens Initializing is strongly recommended at the first stage of setup menu control.
ZOOM/FOCUS > LENS INIT > Press the joystick ‘☟’straight down for about
2 seconds.
MENU V5.xx
1. ZOOM/FOCUS
2. EXPOSURE
3. SCENE ENHANCE
4. 3D-NR
5. DAY/NIGHT
6. PICT ADJUST
7. SPECIAL
8. SYSTEM
9. EXIT
↵
↵
↵
↵
↵
NORMAL
MID
EXT
SAVE&EXIT ↵

Operating Instructions
17
FULL-HD AF ZOOM CAMERA
SAVE & EXIT – Exits the menu after saving the parameters.
EXIT – Exits the menu without saving the menu.
EXIT
ZOOM / FOCUS
FOCUS MODE
D-ZOOM
HOME POSITION
LENS REFRESH
LENS INIT.
RETURN
ZOOM PUSH
OFF
OFF
OFF
ON☟
RET
• ZOOM PUSH: Focusing is activated only when zoom in/out is working.
• AUTO: Focusing is always working.
• MANUAL: Focusing can only be adjusted by ▲,▼ of OSD control joystick
or the remote control via RS-485.
• O-ZOOM RATIO: Sets the Optical ZOOM positon as Home Position.
(x1.0~x3.0 / x1.0~x2.4)
• DURATION: When ZOOM IN/OUT control is accomplished, camera returns to
pre-defined Zoom position after Duration time.
If SMART MOTION / PRESET ZOOM are running, duration for Home position
starts after finishing SMART MOTION / PRESET ZOOM.
1. ZOOM/FOCUS
: ZOOM PUSH, AUTO and MANUAL modes are available for focusing.
1-1. FOCUS MODE (default: ZOOM PUSH)
: D-ZOOM(Digital zoom) is available up to 32x. D-ZOOM starts working when
the optical zoom reaches its maximum tele-position. Zoom ratio is displayed
on the right bottom corner of the monitor if SPECIAL>DISPLAY>ZOOM RATIO
is set to ON.
1-2. D-ZOOM (default: OFF)
: Camera can be configured to return to pre-defined Zoom position automatically
after certain period since ZOOM IN/OUT control is accomplished.
Home Position is recovered even after camera is re-initializing or Power ON/OFF.
1-3. HOME POSITION (default: OFF)

Operating Instructions
18
FULL-HD AF ZOOM CAMERA
HOME POSITION
O-ZOOM RATIO
DURATION
RETURN
OZ X2.0
5sec
RET
2. EXPOSURE
: Can set EXPOSURE MODE to AUTO, IRIS Priority, SHUT. Priority, MANUAL
and Flickerless. SHUT. Priority, MANUAL and Flickerless modes disable
SENS-UP and MOTION BLUR functions.
2-1. MODE (default: AUTO)
: LENS REFRESH can be set to 1~10day and performs the scheduled LENS
Initialization automatically. Every initialization occurs when the time reaches
the scheduled time after setup or power up. When LENS REFRESH initiates
LENS Initialization, a notification ‘LENS INITIALIZING…’ appears on the top
left corner on the monitor.
1-4. LENS REFRESH (default: OFF)
: Lens initialization is necessary during the installation or the regular operation
to align the position data with the mechanical positions whose lens elements
may move and deviate from its calibrated position by the shock or vibration, for
example, during the transportation.
LENS INIT starts the lens initialization when pressing the joystick lever straight
down for about 2 sec.
LENS INIT checks the positions for zoom and focus at both of the end positions
and saves them for the references.
Lens initialization is automatically executed at power up.
1-5. LENS INIT (default: ON ‘☟’)
• It is strongly necessary to execute LENS INIT in cases below;
1) At the final step for the installation.
2) When focus becomes out of control by the shock or vibration.
CAUTION

Operating Instructions
19
FULL-HD AF ZOOM CAMERA
• AUTO: Optimizes the video level by controlling the iris and the shutter speed
automatically.
• IRIS Priority: Selects to fix IRIS in a certain apperture and the video level is
controlled by an automatic shutter control. Lower IRIS LEVEL will close more
iris and increase the field of depth in the daytime but significantly decrease
the low light performance. Too much low IRIS LEVEL will result in the foggy
video by the diffusion from the lens iris.
• SHUT. Priority: Selects to fix SHUTTER speed in a certain speed and the video
level is controlled by an automatic iris control.
This mode is useful when the color rolling occurs under the fluorescent lighting.
It is not recommendable at outdoor in the daytime.
• MANUAL: Iris and Shutter can be set to fix.
• Flickerless : Reduces the flicker in video when US(60Hz)/EU(50Hz) mode is
used in 50Hz/60Hz fluorescent lighting respectively.
• AUTO: SENS-UP is enabled or disabled automatically by the scene brightness.
Higher SENS-UP can get the brighter video but the slower frame rates with
motion blur and more white pixels. If set to AUTO, maximum integration limit
for SENS-UP can be set to x2, x4, X8, x16, X32 in SENS-UP menu.
• OFF: Disables SENS-UP.
: The brighter video can be obtained by increasing the exposure time in the night
with SENS-UP. SENS-UP is the maximum integrations of frame by DSS (Digital
Slow Shutter) in the low light.
2-4. SENS-UP (default: OFF)
: AGC amplifies the video gain for brighter video but noise and white pixel
accordingly. AGC level less than 10 disables AUTO in DAY/NIGHT.
2-5. AGC (default: 10)
EXPOSURE
MODE
BRIGHTNESS DAY
BRIGHTNESS NIGHT
SENS-UP
AGC
MOTION DEBLUR
RETURN
AUTO
OFF
ON
RET
|:::::::|::::::| 10
|::::::|:::::::| 8
|:::::::|::::::| 10
: Adjusts the brightness of day time video(0~20).
2-2. BRIGHTNESS DAY(default:10)
: Adjusts the brightness of night video(0~20).
2-3. BRIGHTNESS NIGHT(default:10)

Operating Instructions
20
FULL-HD AF ZOOM CAMERA
3D-NR is a very sophisticated and powerful time-based noise reduction technology
by monitoring the noise for the several video frames and defining and eliminating
them consecutively at low light. Higher setting reduces noise much more but results
in losing the sharpness and the tail effect or the motion blur for the fast moving
target at low light.
3-4. BLC
3-5. HLC
4. 3D-NR
: Cuts out the highlight area with black mask and excludes it from compensation.
Lower HLC LEVEL cut out video from the lower level.
: Improves the visibility for the dark object by the bright back light.
Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position can be set
by H-POS, V-POS, H-SIZE and V-SIZE.
3-2. WDR
3-3. D-WDR
: Improves the visibility for the high bright area and the dark area by the double
captures of image with LONG and SHORT exposures. With WDR ON, the
frame rate becomes half by the double captures. WDR level can be selected
from LOW, MID and HIGH. Care should be taken to select this mode because
video may lose its quality in some environments by the over compensation.
※CVBS video signal:Connecting 2nd video to CVBS port disables WDR function
temporary. It should be considered when installer adjusts the video with
installation monitor via CVBS video signal.
: Improves the visibility by compensating the video gain for the dark area.
Noise can increase in the dark area accordingly.
3-1. NORMAL (default)
: ON enables MOTION DEBLUR to reduce the motion blur in a certain indoor
enviroment. Noise or color rolling can increase.
2-6. MOTION DEBLUR (default: ON)
3. SCENE ENHANCE
: Optimized for the normal indoor and outdoor in the good lighting condition.

Operating Instructions
21
FULL-HD AF ZOOM CAMERA
: Used when DAY or NIGHT is determined by light level through the lens and
DAY from/to NIGHT is switched automatically by the scene brightness.
D↔N THRESHOLD, D↔N DELY and SMART IR can be set in the menu.
When EXPOSURE>AGC is less than 10, DAY/NIGHT AUTO is disabled and
forcibly switches to ___(DAY) to avoid the malfunction. EXT, B/W (NIGHT)
and COLOR(DAY) is independent on AGC level. When EXTERNAL IR LED
is used with NON IR LED model, please set to IR LED MODE ON.
: DAY or NIGHT is determined by the built-in light photo sensor.
Camera with IR LED must be set to EXT.
DAY/NIGHT is used to control the setting during day-time and night-time operation.
Select the mode according to the light condition and the camera types.
SMART IR can be set to reduce the saturation by the strong IR illumination in the
night in any menu. Setting SMART IR in any menu is identically applied to other
menu. Zero(0) turns off SMART IR and High setting avoids the saturation strongly
but the corners will be darker accordingly.IR LED Control(AUTO/OFF) is available
with IR LED model only. If IR LED is set to OFF, IR LED will be turned OFF but DAY
or NIGHT is still determined by the built-in light photo sensor.
• D↔N THRESHOLD (0~20):
Sets the threshold level switching from/to DAY(color) or NIGHT(B/W).
Setting low level makes camera entered NIGHT at lower light level. High level
makes camera exited NIGHT at brighter light level.
• D↔N GAP (0~15):
Sets the gap level switching from/to DAY(color) or NIGHT(B/W).
5-1. EXT
5-2. AUTO
5. DAY / NIGHT
DAY/NIGHT AUTO
D<->N THRESHOLD
D<->N GAP
D<->N DELAY
SMART IR
RETURN
5s
RET
|:::::::|::::::| 10
|:::::::|::::::| 10
|:::::::|::::::| 10