Eneo PXC-2080Z03 User manual

INSTALLATION AND OPERATION MANUAL
for
PXC-2080Z03

1
Table of contents
1. Safety Instructions and Notes….......................................................................................................
2. General Descriptions............................................................................……………………………...
3. Supplied Items......................................................................................……………………………...
4. Part names…………………………….…...................................................…………………………...
5. Installation Instructions......................................................................................……………………...
6. Setup Menu ……………............................................................................…………………………...
7. Specifications ………………………………………………..................................................................
8. Dimensional Drawings ……………………………………………............................................................
3
3
4
5
6
7
22
24

2
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock
to persons.
Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Caution -- Any changes or modifications in construction of this device which are not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user of the model requires
continued operation during power mains interruptions, it is recommended that the model be powered from
an uninterruptible power supply (UPS) or a battery.”
Notice -- The images used in manual are processed to help comprehension and may
differ from actual video of the camera.
WARNING
NEVER USE THIS CAMERA
1. IN WATER.
2. IN AREA WHERE HAS SHOCK OR VIBRATION WHICH RESULTS IN THE
PROBLEM FOR AUTO FOCUSING.
Caution
To prevent electric shocks
and risk of fire hazards, do
NOT use other than specific
power source.
WARNING

3
1. Safety Instructions and Notes
•Please read this safety and operating instructions before putting the camera into
operation.
•Keep the manual in a safe place for later reference.
• Pay attention to safety when laying the connection cable and observe that the cable is not
subjected to heavy loads, kinks or damage and no moisture can get in.
• Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
• Maintenance and repair have to be carried out only by authorized service centers.
•Use only a mild detergent to clean the housing.
•Keep clean the window surface from the dirt or dust, which may reflect the infrared light to
the lens at night..
•The camera should never be operated beyond the technical specifications. This can lead
to destruction.
•The camera should never be operated in the water.
2. General Descriptions
This camera realizes the natural and crisp image as you see the scene in front of you by
adopting Auto Focus Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves attention.
With 3x Optical Zoom and 32x Digital Zoom,
- Offers the flexible observation
- Provides max. 96x zoom
With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
Main features are;
•OnvifS / PSIA Compatibility
•IP output
•Optical 3X Auto Focus Zoom
•Digital 32X Zoom
•1920x1080p(30fps/25fps)

4
•f3~9mm, 3X Day & Night Zoom Lens
•Wide Dynamic Range
•3D Noise Reduction
•Sense Up(~x8) / AGC(0~20)
•MOTION ZOOM(Automatic Zoom IN/OUT when motion is detected)
•Pointing Zoom (Set the off-centered location to be the center of zoom in Motion Zoom)
•Motion Detection / Motion Deblur / Privacy Mask / Defog
•Focusing Status Indicator on Screen
-(Blue) Focusing in process
-(White) Focusing Completed
•Pixel Defect Compensation
•ID / TITLE / ZOOM RATIO Display
•H / V / HV FLIP
•Lens Refresh / Lens Initializing Set
•LSC(Lens Shade Compensation)
•Enhanced Sensitivity by DSS technology
•Menu Control via WEB
•OSD Menu & Video Sub-out for Easy installation and Maintenance
•H.264/MJPEG Dual stream
•PoE
•Locally recordable with Standard SD Memory
•Input voltage: 24VAC/12VDC (Dual Power)
•Circuit protection against faulty connection.
•Isolated power supply against ground loop problem
3. Supplied Items
•1x FULL HD AF Zoom Camera
•1x Installation and Operating Instructions

5
③
②
④
⑤
ⓐ
ⓑ
ⓒ
ⓔ
ⓓ
ⓕ
ⓖ
ⓗ
4. Part Names
Front view
4.1Rear side view
①
①Window
②
Window Hood
③
Front Body
④
Mount Hole (Top and Bottom)
⑤
Rear Body

6
5. Installation and commissioning Instructions
•Make sure the power is removed before the installation.
•Follow the order for applying power.
First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid an
improper reset from power jitter and a damage from the surge voltage when no load.
5.1. Installation
The camera has a 1/4” thread insert on its top and bottom side for mounting the camera to a tripod or
the wall or ceiling with a corresponding mount.
5.2. Power Supply Connections
Camera can work with either 24VAC or 12VDC, dual voltage power. It does NOT require the polarity-
matched connection for 12VDC supply. Primary and secondary grounds are completely isolated to avoid
the possible ground-loop problems. Its excellently wide operating voltage range of 10.5V-30V for DC and
12-28.8V for AC gives an extra flexibility at the installation.
ⓐIP Reset
ⓑ
OSD menu switches (Up/ Down/ Left/ Right / Enter)
ⓒ
SD Memory Card Slot
ⓓ
LAN Port for RJ45
ⓔ
Power Input Terminal
ⓕ
Alarm Input / Output Terminal
ⓖ
Audio
ⓗ
Video Output Connector (BNC)

7
6. Setup Menu
6.1.1 Network Setup
To access the ADMIN on IP INSTALLER
ID: root
PW: root
The network camera‘s default IP address is: 192.168.1.10.
Therefore, to access the camera for the first time, set the PC‘s address as
192.168.1.XX; for example:
IP Address: 192.168.1.20
Subnet Mask: 255.255.255.0
• Enter the camera’s IP address in the URL bar of the Web browser window and hit “Enter.”
• Enter the default user name (root) and password (root) in the prompt request dialogue.
It is also possible to reset IP parameters to the original factory default settings by pressing
the IP reset

8
If the Information message doesn‘t come out due to the problems like network
failure, you can start the manual installation.
Click the Install ActiveX Control, and the pop-up window will be displayed.
After the installation is successfully completed, Smart Viewer window will be displayed.
- Assigning an IP address
To assign an IP address to the camera proceed as follows:
Click Network Confi guration on the Network Confi guration menu.
Depending on the service type, the network confi guration can be in any of
Static IP, DHCP Client, or PPPoE. You need to set up the network camera

9
according to your network type.
For static IP, select static IP and input values for IP address, NetMask, Gateway,
DNS1, DNS2 and click apply for saving settings. After apply, program
will ask closing web brower for updates, which will take 20~30 seconds.
For DHCP, DHCP server must exist in the network environment. Select
DHCP Client from Network Configuration, click Apply.

10
PPPoE is used to connect eneo products to PPPoE modem provided by ISP.
Since PPPoE needs verifi cation, ID and password are necessary to access network.
Type in ID and password.
- Administrator password
To change the password for the administrator, click Admin Password on System Confi-
guration menu.
Default ID for admin account is fi xed as “root” and not allowed to change.
In Old Password fi eld, enter the current password. In both New Password and Confi rm
Password fi elds, enter the same new password.
The password must be between 4 and 23 alphanumeric letters.
Click Apply button to put it nto eff ect.
Because you have replaced the password with a new one, the existing network connection
made with old password now is lost.
You will have to reconnect using the new password.

11
- Accessing the setup menu
The setup menu can be accessed and controlled either by using the OSD control joy stick
on the side of the camera and a service monitor or by entering the Admin menu in your
web browser.
To access the OSD menu click Camera & Motion in the Device Configuration menu and
click Camera Control.
And for more detailed control for PRIVACY, MOTION and TITLE SET, please click
‘ADVANCED CAMERA MENU”.

12
6.1.2 Camera setup in the menu
Setup menu can be accessed and controlled by OSD control joy stick at the back of camera.
Five commands are available with the joy stick.
Picture of OSD may differ by the models.
In the menu,
use ▲,▼to move menu, ◀,▶to change the settings and press
☟
to select or enter.
The actual value of FACTORY DEFAULT may differ from this manual due to further technical improvements.
Joy stick
SYMBOL descriptions for joystick operation;
-▲,▼,◀,▶denotes the directions of Joystick
lever operation.
-
☟
denotes the long press down straightly
for about 1.5 seconds.
Zoom & Focus Adjustment
(Only works when OSD Menu is not operating)
▲Zoom In
▼Zoom Out
◀Focus Near
▶Focus Far

13
6.2 MAIN menu
Press
☟
to enter the setup menu for about 1 second.
MAIN Default Descriptions
ZOOM/FOCUS - Sets FOCUS MODE, D-ZOOM, LENS REFRESH and LENS INIT.
See ‘6.3 ZOOM/FOCUS’ for detail.
EXPOSURE -
Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and
DEBLUR..
See ‘6.4 EXPOSURE’ for detail.
SCENE
ENHANCE NORMAL
SCENE ENHANCE provides the several ways to enhance the video in
the various environments with the settings in NORMAL, WDR, D-WDR,
BLC and HLC.
MENU V2.0
1. ZOOM/FOCUS
↵
2. EXPOSURE
↵
3. SCENE ENHANCE NORMAL
4. 3D-NR MID
5. DAY/NIGHT EXT
↵
6. PICT ADJUST
↵
7. SPECIAL
↵
8. SYSTEM
↵
9. EXIT SAVE&EXIT
↵

14
MAIN Default Descriptions
SCENE
ENHANCE NORMAL
NORMAL – Optimized for the normal indoor and outdoor in the good
lighting condition.
WDR – Improves the visibility for the high bright area and the dark area
by the double captures of image with LONG and SHORT exposures.
With WDR ON, the frame rate becomes half by the double captures.
WDR level can be selected from LOW, MID and HIGH.
Care should be taken to select this mode because video may lose its
quality in some environments by the over compensation.
D-WDR – Improves the visibility by compensating the video gain for the
dark area. Noise can increase in the dark area accordingly.
BLC – Improves the visibility for the dark object by the bright back light.
Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position
can be set by H-POS, V-POS, H-SIZE and V-SIZE.
HLC – Cuts out the highlight area with black mask and excludes it from
compensation. Lower HLC LEVEL cut out video from the lower level.
3D-NR MID
3D-NR is a very sophisticated and powerful time-based noise reduction
technology by monitoring the noise for the several video frames and defining
and eliminating them consecutively at low light.
Higher setting reduces noise much more but results in losing the sharpness
and the tail effect or the motion blur for the fast moving target at low light.
DAY/NIGHT
EXT
for
IR LED
AUTO
for
No IR
LED
Sets DAY / NIGHT to EXT, AUTO, COLOR and B/W.
SMART IR can be set to reduce the saturation by the strong IR illumination
in the night in any menu of EXT, AUTO and B/W(NIGHT)
Setting SMART IR in any menu is identically applied to other menu.
Zero(0) turns off SMART IR and High setting avoids the saturation strongly
but the corners will be darker accordingly.
IR LED Control(AUTO/OFF) is available with IR LED model only.
If IR LED is set to OFF, IR LED will be turned OFF but DAY or NIGHT is still
determined by the built-in light photo sensor.
EXT – DAY or NIGHT is determined by the built-in light photo sensor.
Camera with IR LED must be set to EXT.
AUTO – Used when DAY or NIGHT is determined by light level through
the lens and DAY from/to NIGHT is switched automatically by the
scene brightness.
D<-->N THRESHOLD, D<->N GAP, D<->N DELY and SMART IR can be
set in the menu.
When EXPOSURE>AGC is less than 12, DAY/NIGHT AUTO is disabled
and forcibly switches to ___(DAY) to avoid the malfunction.
EXT, B/W(NIGHT) and COLOR(DAY) is independent on AGC level.
When EXTERNAL IR LED is used with NON IR LED model, please set
to IR LED MODE ON.
B/W(NIGHT) – Forcibly removes IR cut filter and switches to B/W
regardless of light level.
COLOR(DAY) – Forcibly DAY/NIGHT is disabled and outputs color video.
PICT
ADJUST
Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA,
See ‘6.5 PICT ADJUST’ for detail.
SPECIAL
Sets CAM TITLE, MOTION, PRIVACY, LANGUAGE, PIXEL COMP,
TV SYSTEM. See ‘6.6 SPECIAL’ for detail.
SYSTEM
Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and
FACTORY DEFAULT.
EXIT SAVE & EXIT – Exits the menu after saving the parameters.
EXIT – Exits the menu without saving the menu.

15
6.3 ZOOM/FOCUS
ZOOM /
FOCUS
Default Descriptions
FOCUS
MODE
ZOOM
PUSH
ZOOM PUSH, AUTO and MANUAL modes are available for focusing.
ZOOM PUSH – Focusing is activated only when zoom in/out is working.
AUTO – Focusing is working always.
MANUAL – Focusing can only be adjusted by ▲,▼ of OSD control
joystick or the remote control via RS-485.
D-ZOOM OFF
D-ZOOM(Digital zoom) is available up to 32x.
D-ZOOM starts working when the optical zoom reaches its maximum tele-
position. Zoom ratio is displayed on the right bottom corner of the monitor if
SPECIAL>DISPLAY>ZOOM RATIO is set to ON.
LENS
REFRESH OFF
LENS REFRESH can be set to 1~10day and performs the scheduled LENS
Initialization automatically. Every initialization occurs when the time reaches
the scheduled time after setup or power up.
When LENS REFRESH initiates LENS Initialization, a notification ‘LENS
INITIALIZING…’ appears on the top left corner on the monitor.
LENS INIT ON
☟
Lens initialization is necessary during the installation or the regular
operation to align the position data with the mechanical positions whose
lens elements may move and deviate from its calibrated position by the
shock or vibration, for example, during the transportation.
LENS INIT starts the lens initialization when pressing the joystick lever
straight down for about 1.5sec.
LENS INIT checks the positions for zoom and focus at both of the end
positions and saves them for the references.
Lens initialization is automatically executed at power up.
CAUTION I
It is strongly necessary to execute LENS INIT in cases below;
1) At the final step for the installation.
2) When focus becomes out of control by the shock or vibration.
ZOOM / FOCUS
FOCUS MODE ZOOM PUSH
D-ZOOM OFF
LENS REFRESH OFF
LENS INIT. ON
RETURN RET
↵

16
6.4 EXPOSURE
EXPOSURE Default Descriptions
MODE AUTO
Can set EXPOSURE MODE to AUTO, IRIS Priority, SHUT. Priority,
MANUAL and Flickerless.
AUTO
– Optimizes the video level by controlling the iris and the
shutter speed automatically.
IRIS Priority
– Selects to fix IRIS in a certain apperture and the video level
is controlled by an automatic shutter control.
Lower IRIS LEVEL will close more iris and increase the field of depth in
the daytime but significantly decrease the low light performance.
Too much low IRIS LEVEL will result in the foggy video by the diffusion
from the lens iris.
SHUT. Priority
- Selects to fix SHUTTER speed in a certain speed and the
video level is controlled by an automatic iris control.
This mode is useful when the color rolling occurs under the fluorescent
lighting. It is not recommendable at outdoor in the daytime.
MANUAL
– Iris and Shutter can be set to fix.
Flickerless
– Reduces the flicker in video when US(60Hz)/EU(50Hz)
mode is used in 50Hz/60Hz fluorescent lighting respectively.
SHUT. Priority, MANUAL and Flickerless modes disable SENS-UP and
MOTION BLUR functions.
BRIGHTNESS 10 Adjusts the brightness of video(0~20).
SENS-UP AUTO
The brighter video can be obtained by increasing the exposure time in the
night with SENS-UP.
SENS-UP is the maximum integrations of frame by DSS(Digital Slow
Shutter) in the low light.
AUTO
– SENS-UP is enabled or disabled automatically by the scene
brightness. Higher SENS-UP can get the brighter video but the
slower frame rates with motion blur and more white pixels.
OFF
– Disables SENS-UP.
AGC 12
AGC amplifies the video gain for brighter video but noise and white pixel
accordingly.
AGC level less than 10 disables AUTO in DAY/NIGHT.
MOTION
DEBLUR ON ON enables MOTION DEBLUR to reduce the motion blur in a certain
indoor enviroment. Noise or color rolling can increase.
EXPOSURE
MODE AUTO
BRIGHTNESS |:::::::|::::::| 10
SENS-UP AUTO
↵
AGC |::::::::|:::::| 12
MOTION DEBLUR ON
RETURN RET
↵

17
6.5 PICT ADJUST
PICTURE Default Descriptions
WHITE BAL ATW
ATW, ATWext, ONE PUSH and MANUAL are available for the white
balance modes.
ATW – White balance is continuously working along with the color
temperature changes in the range of 2,000K~8,500K.
ATWext – White balance is continuously working along with the color
temperature changes in the range of 1,800K~11,000K.
ONE PUSH- White balance works only during ● is pressed.
MANUAL – White balance is fixed to the settings by R_GAIN and
B-GAIN. This mode can be used only when the color temperature
does not vary.
SHARPNESS 10 Adjusts the sharpness of video.
COLOR GAIN 10 Adjusts the color level of video.
GAMMA 0.5 Adjusts the gamma of video.
PICTURE
WHITE BAL
SHARPNESS
COLOR GAIN
GAMMA
RETURN
ATW
|:::::|::::::| 10
|:::::|::::::| 10
0.5
RET
↵

18
6.6 SPECIAL
SPECIAL Default Descriptions
MIRROR/FLIP OFF
Reverses the video left and right and/or up and down by MIRROR/FLIP.
OFF - Normal display without mirroring or flipping
Hor. – Video is reversed left and right.
Ver. – Video is reversed upside down.
HV – Video is reversed left and right and upside down.
When the video is reversed by Ver. or HV, then the joystick directions are
reversed accordingly. This feature is very useful when a camera in
installed in upside dawn.
PRIVACY OFF
10 Privacy zones which can be enabled individually by ZON DISP are
available to mask the video.
ZONE NUMBER – Set a number to select a privacy zone from 1~10.
ZONE DISP – ON enables a relevant privacy zone.
H-POS, V-POS, H-SIZE and V-SIZE – Adjust the size and position of
zone.
COLOR – Select the color used for masking the zone form eight colors.
TRANSPARENCY – Defines the transparency for the mask zone.
SPECIAL
MIRROR/FLIP
PRIVACY
MOTION
PIXEL DEFECT
TITLE SET
DISPLAY
DEFOG
RETURN
OFF
OFF
OFF
OFF
↵
↵
OFF
RET
↵

19
MOTION OFF
MOTION can detect the changes in the motion window and displays the
results in blocks and/or a text message.
SENSITIVITY – Adjusts the detection sensitivity for motion.
High value increases the sensitivity to detect the small motion easily.
Too low sensitivity will cause the erratic detection by the tree leaves
or the light level changes.
H-POS,V-POS, H-SIZE and V-SIZE - Adjust the size and position of
the detection window.
BLOCK DISP – ON enables to display the blocks for the detected area.
MOTION OSD – ON enables to display a text message, MOVING !!!,
ZOOM ON MOTION – ON enables to Automatic Zoom IN/OUT when
motion is detected and also enables MOTION OSD to ON.
Area to be zoomed in by ZOOM ON MOTION can be set at SPECIAL>
MOTION> ZOOM ON MOTION >ZOOM TARGET.
Adjusting◀,▶(Joystick) for ZOOM TARGET varies the viewing angle to
be zoomed when the motion occurs..
STAY ZOOMING – Sets the duration time for zooming by Motion.
PIXEL
DEFECT OFF
Detects and compensates the white pixels which become defective.
Once CALIBRATE is selected, the pixel calibration is initiated with lens
closed and can’t cancel.
THRESHOLD – Defines the level of detection and low value detects more
pixels. Be sure to set the value so that the pixels are uniformly blinking
over the entire screen. Too low value will get the bad results because
too many pixels are detected as the bad pixels and the maximum
number of pixels for compensation will be filled by the upper area.
EXECUTE
☟
- Long pressing will execute the pixel calibration for the
detected pixels. Menu will exit automatically after compensation.
TITLE SET -
Camera title(name) can be set and edited up to 15 alpha numeric and
symbolic characters from ASCII codes(ENGLISH only).
▲,▼,◀,▶moves the cursor to choose a character and
☟
selects it.
The selected characters are added and displayed on the top left
Corner and the cursor moves right automatically for next input.
SP - Space is inserted when pressed ●.
BS – Cursor moves back when pressed ●.
CLR – Clears all the characters on input line when pressed ●.
POS – To be able to set the title position by ▲,▼,◀,▶and ●.