Eneo MPC-52A0030P0A User manual

EN
User Manual
1/2,8" HD Camera, Day&Night,
1920x1080, WDR, 30x AF Zoom,
4,3-129mm, Indoor
MPC-52A0030P0A

2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

3
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.

5
Table of Contents
Chapter 1 — Introduction..................................................................................................6
1.1 Features .............................................................................................................................6
Chapter 2 — Installation and Configuration....................................................................7
2.1 Package Contents..............................................................................................................7
2.2 Setting Camera ..................................................................................................................7
2.3 Connections.......................................................................................................................8
2.4 Getting Started...................................................................................................................9
Chapter 3 — Program and Operation.............................................................................10
3.1 Camera Selection.............................................................................................................10
3.2 Accessing the On-Screen Menu Utility...........................................................................10
3.3 How to control the On-Screen Menu Utility ...................................................................10
3.4 Preset ...............................................................................................................................11
3.5 Tour...................................................................................................................................13
3.6 Privacy Zone ....................................................................................................................14
3.7 Camera Menu...................................................................................................................15
3.8 Communication................................................................................................................18
3.9 Alarm ................................................................................................................................20
3.10 System Setup.................................................................................................................21
Appendix A — Specifications.........................................................................................25
Appendix B — Troubleshooting.....................................................................................27

6
Chapter 1 — Introduction
1.1 Features
•Built-in optical power zoom camera with True Night Shot function
•240 Preset positions with the individual camera AE setup
•8 Tours consist of Presets
•16 Privacy Zones
•1 Alarm input, 1 Alarm output (5VTTL)
•Programmable user preferences (alarm, preset, title, etc.)
•Function Run menu using DVR without function key
•Built-in RS-485/422 receiver driver (Up to 3999 selectable camera addresses)
•12VDC for Camera
•Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

7
Chapter 2 — Installation and Configuration
2.1 Package Contents
The package contains the following.
* Dome Camera 1
* Instruction Manual (This Document) 1
2.2 Setting Camera
SW905
You can set video signal with D1 and video type with D2 in SW905.
SW905-D1 Video Signal SW905-D2 Video Type
OFF HD-TVI OUTPUT OFF NTSC
ON AHD OUTPUT ON PAL
You can set coaxitron protocol with D3 and D4 in SW905.
SW905-D3 SW905-D4 HD-TVI OUTPUT AHD OUTPUT
OFF OFF Hikvision-C ACP-PTZ
ON OFF Pelco-C Reserved
OFF ON Reserved Reserved
ON ON Reserved Reserved

8
2.3 Connections
• Connecting to the RS-485/422
The camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS-485 half-duplex, RS-422 full-duplex serial communications signals.
Connect Marked TX+(485+), TX-(485-) to TX+(RX+), TX-(RX-) of the RS-485 control system.
If control system is RS-422, connect TX+(485+), TX-(485-) and RX+, RX- of the camera
to RX+, RX- and TX+, TX- of the control device respectively.
• Connecting HD Output connector
Connect the HD output (BNC) connector to the video input.
• Connecting CVBS Output connector
Connect the CVBS output (BNC) connector to the video input.
• Connecting Alarms
- ALARM IN
You can use external devices to signal the camera to react on events. Mechanical or electrical
switches can be wired to the ALARM IN and GND connectors.
- GND (Ground)
Connect the ground side of the alarm input and/or alarm output to the GND connector.
- ALARM OUT (5VTTL)
The camera can activate external devices such as buzzers or lights. Connect the device to the
ALARM OUT and GND connectors.
• Connecting the Power
Connect power of 12VDC for the camera.
When using a 12VDC adapter, connect the positive (+) pole to the ‘+’ position and
the negative (-) pole to the ‘-’ position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

9
2.4 Getting Started
Once installed apply power to the camera. The camera will start a configuration sequence.
OSD Position
001 AF AE
EMPTY DATA
ALARM:1 CAM ID:0001
INFORMATION
DISPLAY
CAMERA TITLE & ID
FUNCTION TITLE
STATUS of
FOCUS and AE
ALARM DISPLAY

10
Chapter 3 — Program and Operation
3.1 Camera Selection
IF you use the keyboard, before you program or operate a camera, you must select the camera by
pressing No. + CAM keys.
Example: Pressing 1, 0+ CAM keys sequentially will select camera 10. The selected camera
ID will be displayed on the LCD monitor of the keyboard.
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by pressing the MENU key on the
keyboard or DVR, the following On-screen menu utility will appear:
MAIN MENU
PRESET
TOUR
PRIVACY ZONE
CAMERA
COMMUNICATION
ALARM
SYSTEM SETUP
EXIT(ESC TO EXIT)
3.3 How to control the On-Screen Menu Utility
Function Button
Call the On-screen menu utility. MENU
Navigate through the menu items. Up or Down
Go into the sub-menu items. Right, Left or IRIS Open
Change value.
Enter the editing title mode. Right, Left, Tele or Wide
Enter the changing angle mode. IRIS Open
Exit the changing angle mode. IRIS Close

11
3.4 Preset
If you need to view specific places routinely, you should program Presets. A Preset is a
programmed video scene with automatic pan, tilt, zoom, focus, and AE settings. In addition,
Presets may be assigned the “home” position for the camera. As many as 240 Presets, whose
positions are saved in the camera’s firmware, may be programmed.
There are eight pages of Preset menu. Each page has 30 Presets. Pages can be scrolled by
pressing the Right or Left key on the first or last No. of Preset.
PRESET SETUP
NUMBER : 001
TITLE : ------
CAMERA SET
DWELL : -- SEC
1 2 3 4 5 6 7 8 9 0
- * - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
NEXT PAGE
SAVE AND EXIT(ESC TO CANCEL)
-Blank Preset position
*Position has the Preset
!Current cursor position
Follow steps below to store the Preset positions:
1. Press the MENU key to display the main menu on the monitor. Scroll to Preset and press the
Right key.
2. Select the blank Preset position to be stored by pressing the Up, Down, Right or Left key.
3. After selecting a blank position, press the IRIS Open key. Use the Up, Down, Right, Left,Tele
or Wide key to control the direction of the camera and lens.
4. After aiming the camera (view direction and lens control), press the IRIS Close key. The cursor
will be on the “TITLE” after saving data then press the Tele or Wide key to edit the Preset title.
Follow the procedure of the Auto Scan above to edit titles.
5. Press the Tele or Wide key to change the alphanumeric characters and move the next position
by pressing the Right or Left key. Or move down to the character table and press the IRIS
Open key at the desired character then the cursor position moves to the next position
automatically. Press the Right or Left key at the “ALL DELETE” field to delete all characters.
Press the Right or Left key at the “EXIT” field to finish title edit menu.
TITLE EDIT MENU
(CTRL KEY)
002
*
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( )
ALL DELETE
EXIT(ESC TO EXIT)

12
6. Select “CAMERA SET” and press the Right or Left key. Then the Preset camera setup displays.
PRESET CAMERA SETUP
FOCUS : AUTO
MOTION : OFF
MOTION SETUP
AE SETUP
SAVE AND EXIT(ESC TO CANCEL)
Set FOCUS AUTO, MANUAL
Set MOTION OFF, ON
Select “MOTION SETUP” and press the Right or Left key. Then the MOTION setup displays.
MOTION SETUP
SENSITIVITY : 10
POSITION : ALL
DELAY : 00 SEC
OUTPUT : OFF
HOLD TIME : 03 SEC
EXIT(ESC TO EXIT)
Set SENSITIVITY 00 ~ 20
Set POSITION ALL, CENTER
Set DELAY 00 ~ 05 seconds
Set OUTPUT OFF, OUT1
Set HOLD TIME 03 ~ 99 seconds
Select “AE SETUP” and press the Right or Left key. Then the AE setup displays. Refer to the
AE SETUP in the camera setup.
7. Set “DWELL time”. (03 ~ 99 seconds)
8. To select the next page of Presets, scroll the page by pressing the Right or Left key on the first
or last columns of the menu.
9. Repeat step 2 through 8 for each additional Preset position.
10. Select “SAVE AND EXIT” and press the Right or IRIS Open key. Press the IRIS Close key to
exit the program without saving.

13
3.5 Tour
There are 8 programmable Tours. Each Tour consists of up to 40 Preset positions, Patterns, Scans
or other Tours (second-level). Using second-level Tours, it can be expanded to over 300 functions
in a single Tour.
TOUR SETUP
NUMBER : 01
TITLE : T01
TOUR FUNCTION
SAVE AND EXIT(ESC TO CANCEL)
TOUR FUNCTION SETUP
(CTRL KEY)
DWELL : -- SEC
003 --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- T02 --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
EXIT(ESC TO EXIT)
--- Blank position
003 Preset (1 ~ 240)
T02 Tour (1 ~ 8)
Follow the steps below to program the Tours:
1. Press the MENU key to display the main menu on the monitor. Scroll to Tour and press the
Right key to enter the Tour menu.
2. Select “NUMBER” and set the desired number by pressing the Right or Left key.
3. Select “TOUR FUNCTION” and press the Right key to enter the Tour Function Setup menu.
4. Choose a blank position to be programmed by pressing the Up, Down, Right or Left key.
5. To add a stored Preset, press the Tele or Wide key then the stored Preset number displays.
6. To place functions other than Preset, press the IRIS Open key to scroll for Tour.
7. You can also overwrite the programmed number and remove a stored number from the Tour,
press the IRIS Open key until ‘---’ is displaying in the position.
8. Repeat step 2 through 6 for each desired position. Each title will be displayed on top of the line.
9. To edit the “TITLE”, follow the procedure of the Preset above to edit titles.
10. Select “SAVE AND EXIT” and press the Right or IRIS Open key. Press the IRIS Close key to
exit the program without saving.

14
3.6 Privacy Zone
Hide up to 16 unwanted scenes in a camera.
There are four pages of Privacy Zone menu. Each page has 4 Privacy Zones.
PRIVACY ZONE SETUP
(CTRL KEY)
NO METHOD COLOR
01 ON BLOCK BLACK
02 ON BLOCK BLACK
03 OFF ----- BLACK
04 OFF ----- BLACK
NEXT PAGE
SAVE AND EXIT(ESC TO CANCEL)
1. Place the cursor at the field.
2. Press the IRIS Open key then the privacy area menu displays.
Move the desired position by pressing the Right or Left key on the “UP”, “DOWN”, “LEFT” or
“RIGHT” columns of the menu.
Adjust the size by pressing the Right or Left key on the “+” or “-” columns of the menu.
Returns to the previous menu.
PRIVACY AREA MENU
UP
DOWN
LEFT
RIGHT
+
-
EXIT(ESC TO EXIT)
3. To turn the stored zone ON or OFF, press the Tele or Wide key.
4. Set the “COLOR”: “BLACK”, “WHITE”, “YELLOW”, “CYAN”, “GREEN”, “MAGENTA”, “RED” or
“BLUE”.
5. Select “SAVE AND EXIT” and press the Right or IRIS Open key. Press the IRIS Close key to
exit the program without saving.

15
3.7 Camera Menu
CAMERA SETUP
FOCUS CONTROL
WB CONTROL
AE CONTROL
CAMERA CONTROL
SHARPNESS : 03
DIGITAL ZOOM : OFF
IMAGE FLIP : OFF
PRESET FREEZE : OFF
RESOLUTION : 1080P/25
SAVE AND EXIT(ESC TO CANCEL)
SHARPNESS The higher the value, the more edges in the picture will be enhanced.
(0 ~ 10)
DIGITAL ZOOM OFF: Zoom range is limited to the optical.
2X: Zoom is extendable up to 2X of digital range.
4X: Zoom is extendable up to 4X of digital range.
8X: Zoom is extendable up to 8X of digital range.
MAX: Zoom is extendable Max digital zoom range.
IMAGE FLIP This function turns the video output from the camera upside down and
reverses it horizontally.
This option is helpful to install in the opposite side.
PRESET FREEZE ON: the image is frozen during calling Preset.
RESOLUTION HD-TVI Output: 1080P/30, 1080P/25, 720P/60, 720P/50, 720P/30, 720P/25
AHD Output: 1080P/30, 1080P/25
• FOCUS CONTROL
FOCUS SETUP
MODE : AUTO
SENSITIVITY : MID
FOCUS LIMIT : 1M
SAVE AND EXIT(ESC TO CANCEL)
MODE AUTO, MANUAL
Use manual mode in normal use.
SENSITIVITY LOW, LOW.MID, MID, MID.HIGH, HIGH
FOCUS LIMIT This distance is approximate value and the focus operates from the setting
value.
CAUTION: Avoid continuous, 24-hour use of the auto focus. This will shorten the lifespan
of the lens.

16
• WB (White Balance) CONTROL
WB SETUP
MODE : AUTO
R GAIN : ---
B GAIN : ---
SAVE AND EXIT(ESC TO CANCEL)
MODE AUTO, MANUAL, INCANDESCENT, FLUORESCENT, OUTDOOR
AUTO Computes the white balance value output using color information
from the entire screen automatically.
INCANDESCENT Auto white balance mode that is compatible with incandescent lamps.
FLUORESCENT Auto white balance mode that is compatible with fluorescent lamps.
OUTDOOR Outdoor white balance mode
MANAUL Manual mode, you can change R and B Gain manually.
R GAIN 0 ~ 255
B GAIN 0 ~ 255
R GAIN / B GAIN modes are controllable only in MANUAL Mode.
• AE CONTROL
AE SETUP
MODE : AUTO
DSS : OFF
IRIS : AUTO
SHUTTER : AUTO
BRIGHT : 10
GAIN LIMIT : 07
NIGHT SHOT : AUTO
ADDITIONAL AE
SAVE AND EXIT(ESC TO CANCEL)
MODE AUTO, MANUAL, I.PRIO, S.PRIO
AUTO Auto exposure mode
MANUAL Variable Iris, Shutter speed
I.PRIO Variable Iris, Auto Shutter speed
S.PRIO Variable Shutter speed, Auto Iris
DSS OFF, x2 ~ x8
IRIS F1.8 ~ F32
SHUTTER 1/25 (30) ~ 1/30000
BRIGHT 0 ~ 20
GAIN LIMIT 0 ~ 7
NIGHT SHOT AUTO, ON, OFF, GLOBAL
NOTE: Values in ( ) are for NTSC Camera.

17
The NIGHT SHOT option removes the IR cutoff filter of the camera and makes the camera
sensitive to near infrared.
AUTO Camera goes in to B&W mode at low light.
GLOBAL Controlled by the keyboard
(NOTE: GLOBAL function operates F2E protocol only)
The operator can enable NIGHT SHOT for all dome cameras at the same time.
If the NIGHT SHOT mode is set to GLOBAL, “999” + ENTER will turn Off the NIGHT SHOT
mode and “888” + ENTER will turn On the NIGHT SHOT mode.
ON B/W mode
OFF Color mode
NOTE: AUTO in NIGHT SHOT function is not applied in “MANUAL” mode of AE Control.
ADDITIONAL AE
ADDITIONAL AE SETUP
WDR : OFF
WDR WEIGHT : --
BLC : OFF
HLC : OFF
HLC LEVEL : --
HLC COLOR : ---
DEFOG : OFF
EXIT(ESC TO EXIT)
WDR OFF, ON, NIGHT OFF (NOTE: When ON, BLC will be disabled.)
WDR WEIGHT LOW, MID, HIGH
BLC OFF, ON (NOTE: When ON, WDR will be disabled.)
HLC OFF, ON
HLC LEVEL 0 ~ 20
HLC COLOR BLACK, WHITE, YELLOW, CYAN, GREEN, MAGENTA, RED, BLUE
DEFOG OFF, ON
• CAMERA CONTROL
CAMERA CONROL
D/N LEVEL : MID
D/N DELAY : 03 SEC
CHROMA : 08
GAMMA : 2
DNR : MID
DIS : OFF
SAVE AND EXIT(ESC TO CANCEL)
D/N LEVEL LOW, MID, HIGH
D/N DELAY 1 ~ 60 seconds
CHROMA 0 ~ 20
GAMMA 0 ~ 4
DNR OFF, LOW, MID, HIGH
DIS OFF, ON

18
3.8 Communication
To prevent damage, each camera must have a unique address (ID).
The factory default setting is 1.
COMMUNICATION
*
MASTER ID : 0001
*
SLAVE ID : 0001
TYPE : SLAVE
PORT : 485
MASTER PROTOCOL : PELCO-D
SLAVE PROTOCOL : PELCO-D
BAUDRATE : 9600
PARITY : NONE
TERMINATION : OFF
ANSWER : OFF
SAVE AND EXIT(ESC TO CANCEL)
MASTER ID 1 ~ 3999
SLAVE ID 1 ~ 3999
TYPE 485: MASTER, SLAVE
422: MASTER, SLAVE, MASTER/SLAVE
PORT 485, 422
MASTER PROTOCOL PELCO-D, PELCO-P, F2E, F2, NONE
SLAVE PROTOCOL PELCO-D, PELCO-P, F2E, F2, NONE
BAUDRATE 2400, 4800, 9600, 19200, 38400 bps
PARITY NONE, EVEN, ODD
TERMINATION ON, OFF
The device which is connected at end of line, whether it is the camera or keyboard, must have
the cable for communication terminated by setting above. Without proper termination, there is
potential for control signal errors. Total length of the cable for communication should not
exceed 4000 ft (1.2 km).
ANSWER ON, OFF (no acknowledge command from the camera)
This option is helpful to escape the collision of the command using some DVR.
• Control Method
- MASTER:
By using RS-485 or RS-422 TX serial communication port, it allows you to control the external
device (Pan & Tilt System) through CoC (Control over Coax) signal from DVR.

19
- SLAVE:
By using RS-485 or RS-422 RX serial communication port, it allows you to control the camera
by controller or DVR.
- MASTER/SLAVE:
By using RS-422 TX serial communication port, it allows you to control the external device
(Pan & Tilt System) through CoC (Control over Coax) signal from DVR.
By using RS-422 RX serial communication port, it allows you to control the external device
(Pan & Tilt System) by controller or DVR.
If you want to control camera and external device (Pan & Tilt System) by controller and CoC
(Control over Coax) signal from DVR at the same time, you must select TYPE and PORT as
MASTER/SLAVE and 422.

20
3.9 Alarm
ALARM SETUP
(CTRL KEY)
NO FUN IN OUT HOLD LATCH
1 001 NO OUT1 03 OFF
SAVE AND EXIT(ESC TO CANCEL)
NO (Number) Alarm input number
FUN (Function) Stored function number to be called by alarm.
IN (Input) NO/NC – normally open/closed, OFF – ignore
OUT (Output) OUT1 – 5VTTL output, OFF – no output
HOLD Alarm will be held for programmed time. (03 to 99 seconds)
LATCH ON – Alarm message will remain on the screen even though alarm input is
deactivated.
OFF – Alarm message will disappear from the screen after programmed
hold time when alarm input is deactivated.