Eneo MPP-62A0020M0A User manual

EN
User Manual
1/2.8" HD analogue Dome, PTZ,
Day&Night, 20x, 4,7-94mm,
1920x1080, WDR, IP66
MPP-62A0020M0A

2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.

3
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.

5
Table of Contents
Chapter 1 —Introduction..................................................................................................6
1.1 Features ...............................................................................................................................6
Chapter 2 —Installation and Configuration....................................................................7
2.1 Package Contents ...............................................................................................................7
2.2 Mounting the Camera..........................................................................................................8
2.2.1 Locking the Camera......................................................................................................8
2.2.2 Heater Kit Installation (Optional)................................................................................10
2.3 Basic Configuration of Dome Camera System................................................................ 11
2.4 Setting Dome Camera Address (ID) .................................................................................12
2.5 Setting Dome Camera Video Signal & Coaxitron Protocol .............................................12
2.6 Connections.......................................................................................................................13
2.7 Getting Started ..................................................................................................................14
Chapter 3 —Program and Operation.............................................................................15
3.1 Dome Camera Selection....................................................................................................15
3.2 Accessing the On-Screen Menu Utility ............................................................................ 15
3.3 How to control the On-Screen Menu Utility ..................................................................... 15
3.4 Auto Scan (Shortcut: SCAN) ............................................................................................ 16
3.5 Preset (Shortcut: PRST) ...................................................................................................18
3.6 Shortcut of Preset Program.............................................................................................. 20
3.7 Tour (Shortcut: TOUR)......................................................................................................20
3.8 Pattern (Shortcut: PTRN)..................................................................................................22
3.9 Privacy Zone ...................................................................................................................... 23
3.10 Camera Menu...................................................................................................................24
3.11 Dome Communication..................................................................................................... 27
3.12 Alarm ................................................................................................................................ 28
3.13 Dome Setup ..................................................................................................................... 29
Appendix A —Specifications.........................................................................................36
Appendix B —Troubleshooting.....................................................................................38

6
Chapter 1 —Introduction
1.1 Features
The dome camera and the keyboard controller make up the building blocks for any surveil-
lance/security system. Using multiple keyboard controllers and multiple dome cameras, no place is
too large for monitoring. Extensible and flexible architecture facilitates remote control functions for
a variety of external switching devices such as multiplexers and DVRs.
Built-in optical power zoom camera with True Night Shot function
240 Preset positions with the individual camera AE setup
8 Tours consist of Presets, Patterns, Auto Scans and other Tours can be programmed with over
300 functions and preset locations. While moving, each Preset scan can be watched in smooth
Vector Scan mode.
16 Auto Scans with the normal, the vector, and the random mode and the endless Auto-Pan with
13 speed steps
8 Patterns (up to 500 seconds) and 16 Privacy Zones
4 Alarm inputs, 2 Alarm outputs (5VTTL)
Variable speed from 0.1/sec. to 380/sec.
Three Variable speed (SLOW, NORMAL, TURBO)
Turbo speed is 380/sec. with Ctrl key pressed.
Pan/Tilt speed is inversely proportional to the zoom ratio with the option.
Maximum speed is 380/sec. when Preset command.
Auto Calibration from 0.1to 6(Tilt range is -10to 190)
Programmable user preferences (alarm, preset, title, etc.)
180Digital Flip
Up to 3999 selectable camera addresses
Function Run menu using DVR without function key (Pattern, Scan …)
Built-in RS-485 receiver driver
12VDC or 24VAC for Camera
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

7
Chapter 2 —Installation and Configuration
2.1 Package Contents
The dome camera is designed with compact, small size, hard dome camera housing.
The housing is constructed of aluminum, steel and plastic. The housing is designed to be mounted
on a wall or a ceiling. The housing meets the Protection Classification IP66 standards for dust and
moisture resistance.
* Dome Camera 1
* Instruction Manual (This Document) 1
* Template Sheet 1
* Mounting Bracket 1
* Safety Lanyard 1
* Accessory Kit 1
1) Mounting screws (PH6 x 35.0) (4)
2) Plastic anchors (4)
3) O-Rings (4)
4) Torx wrench (1)
* Accessory Connector 1
1) 2-Pin Terminal Block (1)
2) 3-Pin Terminal Block (1)
3) 4-Pin Terminal Block (1)
4) 5-Pin Terminal Block (1)

8
2.2 Mounting the Camera
The dome camera is for use in surface or pendent mounting applications, and the mounting
member must be capable of supporting loads of up to 10 lb (4.5 kg). (Pendent mounting must use
pendent mount accessory.)
The dome camera’s mounting bracket should be attached to a structural object, such as hard wood,
wall stud or ceiling rafter that supports the weight of the dome camera.
CAUTION: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
2.2.1 Locking the Camera
1. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
2. Fix the Mounting Bracket to the ceiling using supplied Anchors (4x) and Mounting Screws (4x)
(Figure B).
3. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
4. Align the locking tab on the bracket and the locking slot on the base of the dome (Figure D).
5. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).

9
CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting
screws "A" on the base of the dome camera to best match the mounting bracket
locked position. Unscrew the locking screw on the side of the dome's base and
fit the tab of the mounting bracket into the locking slot. Screws "A" should not
be too tight or too loose when the dome is in the locked position. After setting
the proper positions of screws "A" remove the mounting bracket and install it to
the proper surface. If it is too difficult to lock the dome in position after the
mounting bracket has been installed readjust the screws "A" by unscrewing
them a small amount and try to install dome camera again.

10
2.2.2 Heater Kit Installation (Optional)
1. Assemble the Heater board to two bossed with screws.
Take a reference "B" in the bottom case as below.
2. Place the Heater in the slot "A".
Heater cable should be placed away from the Main Board.
3. Plug the power connector to the socket "C" (J1) of the Heater Board.
4. 24VAC is recommended to use for the camera power for stable operation with heater kit.
• HEATER (IF APPLICABLE)
Power Supply
24VAC
Power Consumption
10W
Heater ON
at 59°F (15°C)
Heater OFF
at 77°F (25°C)
• POWER
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.
CAUTION: Please reset the camera after 30 minutes when installing it in situations colder
than -10°C.