Eneo VK-1321/PIR User manual

1
Instruction Manual
Hidden CCD Camera VK-1321/PIR (B&W),
VKC-1338/PIR (Colour)

2
Contents
1. Safety Instructions ......................................................................................... 3
2. Description .................................................................................................... 4
3. Installation ..................................................................................................... 5
4. Wiring Instructions ......................................................................................... 6
5. PIR Detector Board Installation and Descriptions ............................................ 7
6. Specifications .............................................................................................. 10
7. Dimensional Drawings ................................................................................. 12

3
1. Safety Instructions
• Read these safety instructions and the operation manual first before you install
and commission the camera.
• Keep the manual in a safe place for later reference.
• Protect your camera from contamination with water and humidity to prevent it
from permanent damage. Never switch the camera on when it gets wet.
Have it checked at an authorized service center in this case.
• Never operate the camera outside of the specifications as this may prevent the
camera functioning.
• Do not operate the cameras beyond their specified temperature, humidity or po-
wer ratings. Operate the camera only at a temperature range of -10°C to +50°C
and at a humidity of max. 90%.
• To disconnect the power cord of the unit, pull it out by the plug.
Never pull the cord itself.
• Pay attention when laying the connection cable and observe that the cable is not
subject to heavy loads, kinks, or damage and no moisture can get in.
• The warranty becomes void if repairs are undertaken by unauthorized persons.
Do not open the camera housing.
• Never point the camera towards the sun with the aperture open.
This can destroy the sensor.
• Installation,maintenance and repair have to be carried out only by authorized
service centers. Before opening the cover disconnect the unit from mains input.
• Thefitter is responsible for the system of protection being followed in accordance
with the technical data, e.g. by sealing of the cable outlet with silicone.
• Contact your local dealer in case of malfunction.
• Only use original parts and original accessories from Videor E. Hartig GmbH.
• Do not use strong or abrasive detergents when cleaning the housing. Use a dry
cloth to clean the dome surface. In case the dirt is hard to remove, use a mild
detergent and wipe gently.
NOTE: This is a class A digital device. This digital device can cause harmful
interference in a residential area; in this case the user may be required
to take appropriate corrective action at his/her own expense.

4
2. Description
This B/W (Colour) HIDDEN CCD Camera uses high sensitive 1/3” interline transfer
CCD Image Sensor (CCD = Charge Coupled Device), and all state circuitry which
provides extremely long life and high reliability.
This Camera offers excellent image quality with low lag and high burn resistance,
and is not subject to distortions from magnetic fields.
Highly resistance to shock and vibration, and easy to install this Camera is a very
good choice for your B/W (Colour) CCTV system.
• For Wall Mount
• Resolution of 600 Horizontal Lines (VK-1321/PIR, # 91989)
Resolution of 470 Horizontal Lines (VKC-1338/PIR, # 91991)
• Built-in Pinhole Lens F2.0/3.7mm
• Electronic Shutter Control (ESC) (VK-1321/PIR, # 91989)
Automatic Shutter Control (AES) (VKC-1338/PIR, # 91991)
• Automatic Gain Control (AGC)
• Automatic White Balance (AWB) (VKC-1338/PIR, # 91991)
• Internal Synchronization
• PIR Sensor Function
• Supply Voltage: 12VDC
• Easy installation

5
3. Installation
1. Secure the bracket to the wall with screws (included).
2. Attach the Camera Case to the bracket.

6
3. Adjust the vertical and horizontal angles by loosening screws (A&B) and
by turning the bracket vertically and horizontally.
4. Wiring Instructions
1. Connect the coaxial cable between the camera and the monitor using a 75ohms
coaxial cable.
2. Insert the AC plug into the AC power socket and the DC plug to the DC Jack.
Note: AC Adapter Sold separately (see Accessories)
Monitor to 24VDC

7
5. PIR Detector Board Installation and Descriptions
Options Description
1. LED Selector
(3 pins: Top, Center, Bottom)
A. Top + Center w/black cap: Upon walk-testing:
Light blinking (disadvantages: Easy to identify
as a security system.)
B. Center + Low w/black cap: No light blinking
while detecting. (advantages: less obvious)
2. Sensitivity Adjustment A. To raise sensitivity: Turn clockwise to detect
longer distance and wider pattern.
B. To lower sensitivity: Turn counter clockwise
for detection in narrow areas.
3. Dwell Time Adjustment
Adjustable from 2 to 40sec.
For closure period of N.C/N.O relay connected to
an alarm panel, light control or recording control
of time lapse VCR, etc.
A. Max. time: Turn counter clockwise
B. Min. time: Turn clockwise
Top + Center pins of „J3” must be selected
to adjust the time setting.
J1
High Low
„VR1”
Min. Max.
„VR2”
Output Terminals
Pulse Count
Light Control
Recording Control
Time Adjustment
LED Selector
Sensitivity
Adjustment
N.C.
J1 J2
VR1
N.O.
1
2
3
45
6
J3
Com
Com
VR2
3
2
1
3
2
1
3
2
1

8
Options Description
4. Alarm control, Light
control or Recording
control (N.O or N.C)
(3 pins: Top, Center,
Bottom)
A. Top + Center w/black cap: Operate with „VR2”
to adjust time. (To set the relay output of the
Light control or Recording control, the time is
selected by individual preference or application.
B. Center + Bottom w/black jumper: Relay output
can be set for Security control panel for only
2 seconds.
Note: N.C./N.O. relay output current:
1A 125VAC, 2A 30VDC.
5. Pulse Control
Once or twice
A Set to „ONCE” for instant reaction when PIR
detects someone: and either the „alarm or
Security control panel” or „Recording control”
will be triggered immediately.
B Set to „Twice” when PIR detects someone
2 times within 15 seconds.
6. Output Terminals
24 Hour/Anti-Tamper
N.C.: Normally Closed
A. For connection to: Security panel or
Light control CCTV ...etc.
B. With anti-tamper function for 24 hours.
N.O.: Normally Open Contacts
Note: Relay output current:
1A 125VAC, 2A 30VDC
7. Power: 12VDC
Standby Current: 3mA,
Working Current: 28mA
Caution:
The PIR is triggered by body movement,
excluding fixed objects, however, do not place
in direct sunlight or reflected sunlight.
J3
J2
A
B
N.C.
N.O.
Com
Com

9
• Wide angle lens up to 100°, coverage areas to 30x30 feet
• Provide 64 beams in 3 layers
100° Top view
Side view
10 20 30 feet 10 20 30 feet

10
6. Specifications
Type VK-1321/PIR VK-1338/PIR
Art, No. 91989 91991
System Black/white Colour
Video standard CCIR PAL
Sensor size 1/3”
Imager CCD, Sony Super HAD Interline Transfer
Synchronization Internal
Signal-to-noise ratio 48dB
Gamma correction 0.45
Horizontal resolution 600 TVL 470 TVL
Sensitivity
(at 50% video signal)
0.23Lux at F1.2;
0.65Lux at F2.0
(Videor measurement
result)
2.0Lux at F1.2 (Videor
measurement result),
5.6Lux at F2.0
Autom. electron. shutter (ESC) 1/50 ~ 1/100,000sec.
Low Speed Shutter no
Automatic gain control (AGC) Supplied
Digital Noise Reduction (DNR) no
White Balance – Automatic
Backlight compensation no
Wide Dynamic Range (WDR) no
IR cut filter no Standard
Video outputs VBS CVBS
Lens type Fixed focal length
Lens F2.0/3.7mm Pinhole
Aspherical technology no
Focal length 3.7 mm
Horizontal angle of view 68°
Iris control no
Filter screw size Not available
MOD (Min. object distance) 0.1 m