Eneo PXD-2080Z03 B Installation instructions

Full Manual
1/2.9" Network Camera
PXD-2080Z03 B

Table of contents
1. Safety Instructions and Notes….......................................................................................................
2. General Descriptions............................................................................……………………………...
3. Supplied Items......................................................................................……………………………...
4. Part names…………………………….…...................................................…………………………...
5. Installation Instructions......................................................................................……………………...
6. Setup Menu ……………............................................................................…………………………...
7. Specifications ………………………………………………..................................................................
8. Dimensional Drawings ……………………………………………..........................................................
3
3
5
6
7
13
28
30
1

To prevent fire or shock hazard, do not expose the unit to rain or moisture.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock
to persons.
Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Caution -- Any changes or modifications in construction of this device which are not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user of the model requires
continued operation during power mains interruptions, it is recommended that the model be powered from
an uninterruptible power supply (UPS) or a battery.”
Notice -- The images used in manual are processed to help comprehension and may
differ from actual appearance of the camera.
WARNING
NEVER USE THIS CAMERA
1. IN WATER.
2. IN AREA WHERE HAS SHOCK OR VIBRATION WHICH RESULTS IN THE
PROBLEM FOR AUTO FOCUSING.
Caution
To prevent electric shocks
and risk of fire hazards, do
NOT use other than specific
power source.
WARNING
2

1. Safety Instructions and Notes
• Please read this safety and operating instructions before putting the camera into
operation.
• Keep the manual in a safe place for later reference.
• Pay attention to safety when laying the connection cable and observe that the cable is not
subjected to
heavy loads, kinks or damage and no moisture can get in.
• Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
• Maintenance and repair have to be carried out only by authorized service centers.
• Use only a mild detergent to clean the housing.
• Keep clean the window surface from the dirt or dust, which may reflect the infrared light to
the lens at night..
• The camera should never be operated beyond the technical specifications. This can lead
to destruction.
• The camera should never be operated in water.
2. General Descriptions
This Network camera realizes the natural and crisp image as you see the scene in front of
you by adopting Auto Focus Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves attention.
With 3X Optical Zoom and 32X Digital Zoom,
- Offers the flexible observation
- Provides max. 96X zoom
With ICR mechanism,
- Enhances its sensitivity about 10X at night time
- Can accepts the infrared light
With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
Main features are;
•Onvif / PSIA Conformance
•Optical 3X Auto Focus Zoom • Digital 32X Zoom
•f3~9mm, 3X Day & Night Zoom Lens
•1920x1080p(30fps/25fps)
•Wide Dynamic Range
•Sense Up(~x8) / AGC(0~20) / 3D Noise Reduction
3

•SMART MOTION ZOOM(Automatic Zoom IN/OUT when motion is detected)
•Pointing Zoom which enables the flexible zooming at any area
•Motion Detection / Motion Deblur / Privacy Mask / Defog
•Focusing Status Indicator on Screen
- (Blue) Focusing in process
- (White) Focusing Completed
•Pixel Defect Compensation
•ID / TITLE / ZOOM RATIO Display
•H / V / HV FLIP
•Lens Refresh / Lens Initializing Set / LSC(Lens Shade Compensation)
•Enhanced Sensitivity by DSS technology
•Menu Control via either Local Joystick or WEB
•OSD Menu & CVBS Video Sub-out for Easy installation and Maintenance
•H.264/MJPEG dual streaming with TI DM365/368 engine
•Full duplex 2 way Audio, Alarm IN/OUT
•Max 30fps live view @ 1920x1080p
•MICRO SD memory card slot for Local recording
•PoE (Power Over Ethernet), IEEE 802.3af
•Input voltage: 24VAC/12VDC dual type of Local power
•Circuit protection against faulty connection in Power Polarity
•Isolated power supply against ground loop problem.
•Built in cooling Fan and Heating function
•Anti-Scratch Hard Coated Clear Bubble
•Changeable surface mount and flush mount
•Perfect 3-Axis gimbal
•2 High power LEDs
• IP 67 / IK 10 Protection
4

3. Supplied Items
• 1x MegaPixel Network AF Zoom Camera
• 1x Installation and Operating Instructions
• 1x ①Pipe hole cap
• 1x ②Pipe Spacer
• 1x ③L-shape hex wrench
• 3x ④Wrench Bolt for surface mount
• 4x ⑤Anchors
• 4x ⑥Mount screws
• 1x ⑦BM Screw
• 1x ⑧Sub-out cable
• 1x ⑨Coupler for RJ45 Cable
• 1x ⑩EMI Ferrite Core
①
②
③
⑤
⑥
⑧
⑦
⑨
④
⑩
5

4. Control and Part names
ⓐLens
ⓑLight sensor for IR LEDs
ⓒIR LEDs
ⓓIP RESET
ⓔMICRO SD Card Slot
ⓕRTx Status Indicator
ⓖOSD control joy stick
ⓗVideo Sub-output
ⓘMount holes(x3) for dome base
ⓙClear bubble
ⓚRing cover fixing screws(x3)
ⓛRing cover
ⓜSurface mount holes(x4)
ⓝDome base fixing screw taps(x3)
ⓞPipe hole
ⓟPipe spacer
ⓕ
ⓖ
ⓘ
ⓗ
ⓐ
ⓑ
ⓒ
ⓔ
ⓞ
ⓝ
ⓜ
Surface Mount Base
ⓙ
ⓚ
ⓛ
ⓟ
ⓓ
Dome Bubble Assembly
6

5. Installation
5.1 Installation Instructions
•Make sure the power is removed before the installation.
•Follow the order for applying power.
First, connect the low voltage (AC24V or DC12V), then plug the AC adapter to AC outlets to avoid an
improper reset from power jitter and a damage from the surge voltage when no load.
Joy stick
VIDEO
SUB-OUT
connector
WARNING NEVER USE THIS CAMERA
1) in WATER.
2) in area where has SHOCK or VIBRATION which results in the problems for Auto Focus operation.
Zoom & Focus Adjustment
(Only works when OSD Menu is not operating)
▲Zoom In
▼Zoom Out
◀Focus Near
▶Focus Far
SYMBOL descriptions for joystick operation;
-▲,▼,◀,▶denotes the directions of Joystick lever
operation.
-
☟
denotes the long press down straightly
for about 2 seconds.
IP Reset (Press over 10 sec by stick driver)
7

5.2 Surface mount
Surface mount
base
⑥Mount screws
and ②pipe hole
cap for surface
mount base
Dome base
assembly
④Wrench bolts
for fitting to
surface mount
base
Dome bubble
assembly
L-Wrench
Quick installation guides;
1. Locate the mounting template at the installation position
and drill the ceiling or wall if needed.
2. Place Surface mount base on pre-drilled position and fix it
through
ⓙ
Surface mount holes(x4) by using ⑥Mount screws.
Assemble the cable pipe, otherwise tighten
①
pipe hole cap.
3. Open Dome bubble assembly by loosening
ⓘ
Ring cover
fixing screws(x3)
CAUTION
Extreme care should be taken NOT to scratch the dome
surfaces and to protect it from dirt or dust at any time.
4. ⓕMount holes(x3) for dome base and ⓚhole should be
aligned before fixing Dome base assembly to Surface mount
base by using ④Wrench bolts. And tighten ④wrench bolts
5. Route the power/ video cable to the connecting place.
CAUTION
Care should be taken the cable is NOT to be damaged,
kinked or exposed in the hazardous area.
6. Set the camera’s angle (Pan, Tilt, inclination)
7. Adjust ZOOM/FOCUS by OSD menu or manual
8. Put Dome bubble assembly over Dome camera assembly and
tighten
ⓗ
Ring cover fixing screws(x3) by using
③
L-shape hex
wrench
CAUTION
Tighten enough
ⓗ
Ring cover fixing screws(x3) so that
there should be NO gap between
ⓔ
Lens and
ⓖ
Clear bubble to avoid the light inflow from IR LEDs.
Ceiling or wall
8

5.3 Flush mount
⑥Mount screws
Dome base
assembly
Quick installation guides;
1. Locate the mounting template at the installation position
and drill the ceiling or wall if needed.
2. Open Dome bubble assembly by loosening
ⓘ
Ring cover
fixing screws(x3)
CAUTION
Extreme care should be taken NOT to scratch the dome
surfaces and to protect it from dirt or dust at any time.
3. Place Dome base assembly on pre-drilled position and fix it
through
ⓕ
mount holes(x3) by using ⑥Mount screws.
(Use three screws only out of ⑥Mount screws(4x))
4. Route the power/ video cable to the connecting place.
CAUTION
Care should be taken the cable is NOT to be damaged,
kinked or exposed in the hazardous area.
5. Set the camera’s angle (Pan, Tilt, inclination)
6. Adjust ZOOM/FOCUS by OSD menu or manual
7. Put Dome bubble assembly over Dome camera assembly and
tighten
ⓗ
Ring cover fixing screws(x3) by using ③L-shape hex
wrench
CAUTION
Tighten enough
ⓗ
Ring cover fixing screws(x3) so that
there should be NO gap between
ⓔ
Lens and
ⓖ
Clear bubble to avoid the light inflow from IR LEDs.
Ceiling or wall
Dome bubble
assembly
L-Wrench
9