Eneo Vkc-1416b-/pp User manual

Installation and Operating Manual

1/4” Day/Night Camera, Outdoor Housing, 22x Zoom

VKC-1416B-/PP

Contents

1. Safety Instructions ........................................................................................................................................................................................................................... 3

2. Introduction ..................................................................................................................................................................................................................................... 3

2.1 General Description ................................................................................................................................................................................................................ 3

2.2 Parts Supplied ........................................................................................................................................................................................................................ 3

3. Camera Installation .......................................................................................................................................................................................................................... 4

3.1 Package Contents................................................................................................................................................................................................................... 4

3.2 Operation Requirements ......................................................................................................................................................................................................... 4

3.3 Parts Name............................................................................................................................................................................................................................. 5

3.4 Installation.............................................................................................................................................................................................................................. 5

3.4.1 Installation 1 (Cable through the Wall with the Mount Base) ....................................................................................................................................... 6

3.4.2 Instillation 2 (Using the Conduit Knockout punched with Mount Base)......................................................................................................................... 7

4. Connection....................................................................................................................................................................................................................................... 8

4.1 Colour Lead Wire & Colour Display Label................................................................................................................................................................................. 8

4.2 External Day/Night Control & Zoom Preset Control .................................................................................................................................................................. 9

4.3 Motoion Detection & Face Detection Control ........................................................................................................................................................................... 9

4.4 RS-485 Connection ............................................................................................................................................................................................................... 9

4.5 Power Connection................................................................................................................................................................................................................. 10

4.6 External A/D Key Control....................................................................................................................................................................................................... 10

5. Settings in the OSD Menu .............................................................................................................................................................................................................. 11

5.1 OSD Main Screen ................................................................................................................................................................................................................. 11

5.2 Main Menu ........................................................................................................................................................................................................................... 11

5.2.1 FOCUS ..................................................................................................................................................................................................................... 11

5.2.2 WB (White Balance).................................................................................................................................................................................................. 11

5.2.3 AE (Auto Exposure)................................................................................................................................................................................................... 12

5.2.4 BLC/WDR ......................................................................................................................................................................................................................12

5.2.5 ALARM/MD/FD ......................................................................................................................................................................................................... 12

5.2.6 PRIVACY................................................................................................................................................................................................................... 13

5.2.7 SPECIAL ................................................................................................................................................................................................................... 13

5.2.8 EFFECT .................................................................................................................................................................................................................... 13

5.2.9 CAM SET.................................................................................................................................................................................................................. 14

6. Troubleshooting ............................................................................................................................................................................................................................. 14

7. Maintenance.................................................................................................................................................................................................................................. 14

8. Speciﬁcations ................................................................................................................................................................................................................................ 15

9. Dimensional Drawings ..................................................................................................................................................................................................................... 16

Betriebsanleitung

Installation and Operating Instructions

Mode d’emploi

Instrukcja instalacji i obsługi

www.videor.com

www.eneo-security.com

⇒

1. Safety Instructions

• Read these safety instructions and the operation manual ﬁrst before you install and commission the camera.

• Keep the manual in a safe place for later reference.

• Protect your camera from contamination with water and humidity to prevent it from permanent damage.

Never switch the camera on when it gets wet. Have it checked at an authorized service center in this case.

• Never operate the camera outside of the speciﬁcations as this may prevent the camera functioning.

• Do not operate the cameras beyond their speciﬁed temperature, humidity or power ratings.

Operate the camera only at a temperature range of -10°C to +50°C and at a humidity of max. 90%.

• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.

• Pay attention when laying the connection cable and observe that the cable is not subject to heavy loads, kinks, or damage and no moisture can get in.

• The warranty becomes void if repairs are undertaken by unauthorized persons.

Do not open the camera housing.

• Never point the camera towards the sun with the aperture open. This can destroy the sensor.

• Installation, maintenance and repair have to be carried out only by authorized service centers.

Before opening the cover disconnect the unit from mains input.

• The ﬁtter is responsible for the system of protection being followed in accordance with the technical data, e.g. by sealing of the cable outlet with silicone.

• Contact your local dealer in case of malfunction.

• Only use original parts and original accessories from Videor E. Hartig GmbH.

• Do not use strong or abrasive detergents when cleaning the dome. Use a dry cloth to clean the dome surface.

In case the dirt is hard to remove, use a mild detergent and wipe gently.

• During assembly, care must be taken to ensure that existing seals are correctly inserted and are not displaced as a result of assembly.

You must not continue to use damaged seals.

NOTE: This is a class A digital device. This digital device can cause harmful interference in a residential area; in this case the user may be required to take

appropriate corrective action at his/her own expense.

2. Introduction

2.1 General Description

The 22x AutoFocus Zoom WDR Day & Night Camera provides especially for closed circuit television (CCTV) and security surveillance application.

CAUTION: Use at the 12VDC adapter must provide the power consumption of above 500mA.

• High Resolution Colour/B&W Camera

• Integral 22x AF zoom lens / 16x digital zoom

• Digital Signal Processing (DSP)

• Enhanced dynamic range (WDR/EDR)

• Digital image stabilization (DIS)

• Digital noise reduction (DNR)

• Programmable backlight compensation (BLC)

• High speed shutter control (ESC+MES)

• Adjustable low speed shutter control (DSS)

• On-screen menu control

• RS-232/RS-485 serial and voltage control interface

• All-in-one: camera / lens / housing IP66

2.2 Parts Supplied

• 1/4” Colour camera VKC-1416B/IR

• Screw set

• Manual

3. Camera Installation

Installation of the camera must be performed by qualiﬁed service personnel in accordance with all local national electrical and mechanical codes must perform

installation of the camera.

Perform the following steps to install the camera

3.1 Package Contents

• Camera VKC-1416B/PP

• Instruction Manual

• Mounting Kit

3.2 Operation Requirements

RS-485

Camera 1

Multiplexer

Video

Monitor

Camera 2 Camera 3 ...

J-Box

RS-485

Keyboard DVR / VCR

RS-485

Video

Typical System Conﬁguration

1Sunshield

2AF camera module

3Mount base

4Bimetal

5Heater

6Connection cable

7Cable label

3.3 Parts Name

Carefully remove the contents from the box, and verify that nothing was damaged in shipment.

3.4 Installation

There are two ways of installing the camera.

1. Cable through the wall with mount base. 2. Using the conduit knockout punched with

the mount base.

3.4.1 Installation 1 (Cable through the Wall with the Mount Base)

A. Drill the mounting location, using the template sheet (or the bottom of the mount base) as a template.

B. Insert the plastic anchors into the hole which has just drilled.

C. Connect BNC cable and communication lines.

D. Fit the screw holes of the mount base into the plastic anchors.

E. Screw up the M6 torx screws (T-20).

F. Adjust the camera suitably using the pan & tilt function, and ﬁx the camera using the socket set screw, hexagon wrench.

Seal around the stand base tightly using the silicon rubber.

Mount base

Wall

Plastic anchors (4x)

Torx screws (T-20)

M6.0 x 35.0 (4x)

Set screw

M5.0, L=5.0mm

Hexagon wrench

Socket set screw

M5.0, L=5.0mm

3.4.2 Instillation 2 (Using the Conduit Knockout punched with Mount Base)

A. Drill the mounting location, using the template sheet (or the bottom of the mount base) as a template

B. Insert the plastic anchors into the hole which has just drilled.

C. Connect BNC cable and communication lines.

D. Fit the screw holes of the mount base into the plastic anchors.

E. Remove the conduit knockout punched for the cable entry.

F. Screw up the M6 torx screws (T-20).

G. Adjust the camera suitably using the pan & tilt function, and ﬁx the camera using the socket set screw, hexagon wrench.

Mount base

Wall

Torx screws (T-20)

M6.0 x 35.0 (4x)

Socket set screw

M5.0, L=5.0mm

Hexagon wrench

A conduit knockout punched for

the cable entry

Cable

Plastic anchors (4x)

Colour Description

Red 12VDC (+) / 24VAC

White 12VDC (–) / 24VAC

Pink RS-232 TXD

Sky-blue RS-232 RXD

Black GND

Gray EXT-IN

Black/white EXT-OUT

Blue RS-485 (–)

Green RS-485 (+)

Orange A/D KEY

Violet MD-OUT

Connection cable description

Video (BNC)

Monitor

DVR / VCR

RS-485 connection

A/D key control

M/D control

Day & night control

(black)

(violet)

(gray)

(black/white)

(black)

(orange)

(blue)

(green)

4. Connection

CAUTION: Do not connect the power cable until all other connections have been completed. if you complete the whole connection of cameras, then you

have to cut the extra cable.

4.1 Colour Lead Wire & Colour Display Label

GND (black)

EXT-OUT

(black/white)

EXT-IN (gray)

4.2 External Day/Night Control & Zoom Preset Control

Is connect to an external sensor to receive day/night detection signals.

External sensor switch ON/OFF

Day/Night

EXT-IN Day: open

Night: closed

EXT-OUT Colour mode: 0V output

B/W mode: 5V output

NOTE: To validate the sensor inputs, select Function menu B/W mode the EXT.

Zoom Preset

EXT Zoom Preset

4.3 Motion Detection & Face Detection Control

M/D or F/D Normal mode: 0V output

Alarm mode: 3V output

M/D+EXT or

F/D+EXT

Normal mode: 0V output

Alarm mode: 3V output

GND (black)

MD or F/D-OUT

(violet)

RS-485

RS-485 (+)

(green)

RS-485 (–)

(blue)

4.4 RS-485 Connection

Connecting to the RS-485: The camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex.

Connect market Rx+, Rx- to Tx+, Tx- of the RS-485 control system.