Eneo PXB-2080Z03 D User manual

Quick Installation Guide
1/3” Network Camera,
WDR, Day&Night, 3-9mm,
1920x1080, 3x AF Zoom, Infra-
red, PoE
PXB-2080Z03 D
EN

Safety Precaution
03
NETWORK AF-ZOOM CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

Safety Precaution
04
NETWORK AF ZOOM CAMERA
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the
cable is not subjected to heavy loads, kinks or damage and no moisture can get
in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

Contents
05
NETWORK AF ZOOM CAMERA
Safety Precaution
p.03~04
Contents
p.05
Features
p.06~07
Composition
p.07
Dimensions
p.08
Part Names
p.08
Installation Instructions
p.09~11
Operating Instructions
p.12~28
Specifications
p.29~30

Features
Key Features
06
NETWORK AF ZOOM CAMERA
• Full HD, 2Mega Pixel, NETWORK CAMERA, 1920x1080(30p/25p)
• ONVIF & PSIA Conformance
• Built-in f=3~9mm, F1.2~F2.1 Day&Night zoom lens
(Optical 3x Auto focus zoom / Digital 32x zoom)
• Real time True WDR (Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• Dual Filter Switcher
• Color D/N, optimized color mode for night
• Focusing Status Indicator on Screen
- ★(Blue) Focusing in process
- ★(White) Focusing Completed
• Various Zooming Technologies
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
- Pointing Zoom (which enables the programmable zooming at any area)
- Preset Zoom
• Home Position setting
• Motion Detection, Privacy Mask, Defog, Sens-up, BLC/HLC, H/V/HV Flip,
Smart IR, Title Set, Motion Deblur
• ID / TITLE / ZOOM RATIO DISPLAY
• Enhanced Sensitivity by DSS technology
• H.264 / MJPEG dual streaming
• Full duplex 2 way Audio, Alarm IN/OUT
• Max 30fps live view @ 1920x1080p
• Audio & Alarm input/output
• Slot for Standard SD memory card verified up to 32GB
• Zoom & Menu Control via either Local Joystick or WEB
• OSD menu & CVBS Video output BNC for easy installation & maintenance
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• PoE(IEEE Std. 802.3af) & Local dual power
• Built-in 4 High power LEDs
• LED ON/OFF Control
• Dual Window, One touch 3-Axis locking bracket, Easy Installation Pad
• Built-in Cooling Fan & Heating function
• IP67 Protection

Features
07
NETWORK AF ZOOM CAMERA
Composition
Torque Wrench:
3mm (1pc)
Video Sub-out:
Cable (1pc)
General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With 24VAC/12VDC dual power & PoE (Power Over Ethernet) design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front
of you by adopting Auto Focus Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
Coupler for
RJ45 Cable (1pc)
EMI Ferrite
Core (1pc)
Mounting Template
Operating
Instruction
Camera
Assembly Screw:
4 x 14mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Easy
Bracket
Wiring Connector
(1pc)
Cable Signal
Sticker

Dimensions
08
NETWORK AF ZOOM CAMERA
Part Names
(unit : mm)
ETHERNET &
POWER CABLE
267
108
87.30
100
86.40
75.90
80
190
DUAL WINDOW
SUNSHIELD BOLT
SUNSHIELD
FRONT CASE
EASY
BRACKET
OSD Setup
CONTROL COVER
LOCK/UNLOCK
SCREW
BRACKET
REAR CASE

Installation Instructions
09
NETWORK AF ZOOM CAMERA
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken the cable is NOT to be damaged, kinked or exposed
in the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun
or spot light.
Torque Wrench
Assembly Screw
: 4x14mm
Mounting Screw
: 4x30mm
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.
3. Route the power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x14mm).
5. Set the camera’s viewing angle.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
CAUTION
REAR VIEW
1
2
3
4
Cable exit

Installation Instructions
10
NETWORK AF ZOOM CAMERA
• Unlock the screw on the camera bracket through using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
88°
90°
±90°
• on the wall • on the ceiling
■Adjustment of viewing angle with a bracket
Torque
wrench
Lock/Unlock
Screw

Installation Instructions
11
NETWORK AF ZOOM CAMERA
Power Supply Connections
Camera can work with either 24VAC or 12VDC, dual voltage power and PoE
(IEEE Std. 802.3af). Primary and secondary grounds are completely isolated
to avoid the possible ground-loop problems.
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• After all connections are finished properly, follow the order for applying power.
a) Plug the network cable into RJ-45 Ethernet Port.
If PoE is the unique power, there will be no need to connect Power terminal.
b) When DC12V or AC24V Local power is necessary, first connect the low
voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid
an improper reset from power jitter and a damage from the surge voltage
when no load.
50mm
50mm
EMI Ferrite Core Connection
~24V/DC12V (RED)
~24V/GND (BLACK)
ALARM-IN (GREEN)
ALARM-OUT (BLUE)
GND (GRAY)
AUDIO-IN (BROWN)
GND (GRAY)
AUDIO-OUT (ORANGE)
► When PoE and Local dual power are connected at the same time,
Local power has priority.

Operating Instructions
12
NETWORK AF ZOOM CAMERA
Setup menu can be accessed and controlled by OSD control joy stick on the
side of camera unit.
Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.
4) ‘☟’denotes the long press down straightly for about 2 seconds
Using OSD controller
OSD Control
Joy Stick
IP RESET
Standard
SD Card Slot
Video Sub-out Connector
Cover Open
Description of the ZOOM&FOCUS* adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
3) ◄: Focus Near
4) ► : Focus Far
(*) Works only when OSD Menu is inactive and IP is not connected.

Operating Instructions
13
NETWORK AF ZOOM CAMERA
Quick Network Setup
After camera is connected with IP, its control is available via WEB Viewer.
To access the ADMIN on IP INSTALLER
ID: root
PW: root
The network camera‘s default IP address is: 192.168.1.10.
Therefore, to access the camera for the first time, set the PC‘s address as shown.
192.168.1.XX; for example:
IP Address: 192.168.1.20
Subnet Mask: 255.255.255.0
• Enter the camera’s IP address in the URL bar of the Web browser window and
hit “Enter.”
• Enter the default user name (root) and password (root) in the prompt request
dialogue. It is also possible to reset IP parameters to the original factory default
settings by pressing the IP reset.
• If the Information message doesn‘t come out due to the problems like network
failure, you can start the manual installation.
• Click the Install ActiveX Control, and the pop-up window will be displayed.
After the installation is successfully completed, Smart Viewer window will be
displayed.
NOTICE

Operating Instructions
14
NETWORK AF ZOOM CAMERA
1. Assigning an IP address
To assign an IP address to the camera proceeded as follows:
Click Network Configuration on the Network Configuration menu.
• Depending on the service type, the network configuration can be in any of Static
IP, DHCP Client, or PPPoE. You need to set up the network camera according to
your network type.
• For static IP, select static IP and input values for IP address, NetMask, Gateway,
DNS1, DNS2 and click apply for saving settings. After apply, program will ask
closing web browser for updates, which will take 20~30 seconds.

Operating Instructions
15
NETWORK AF ZOOM CAMERA
2. Administrator password
To change the password for the administrator, click Admin Password on System
Configuration menu.
• For DHCP, DHCP server must exist in the same network environment. Select
DHCP Client from Network Configuration, click Apply.
• PPPoE is used to connect IP products to PPPoE modem provided by ISP.
Since PPPoE needs verification, ID and password are necessary to access
network. Type in ID and password.
• Default ID for admin account is fixed as “root” and not allowed to change.
In Old Password field, enter the current password. In both New Password and
Confirm Password fields, enter the same new password.
• The password must be between 4 and 23 alphanumeric letters. Click Apply to
put it into effect. Because you have replaced the password with a new one, the
existing network connection made with old password now is lost.
• You will have to reconnect for using the new password.

Operating Instructions
16
NETWORK AF ZOOM CAMERA
Camera SETUP menu can be accessed in two ways via web viewer.
Most frequent controls are available with the parameters directly in the below
table. More complicated settings such as PRIVACY, POINTING ZOOM & SMART
MOTION settings are available via ‘ADVANCED CAMERA MENU’ by activating
the camera OSD menu.
3. Accessing the camera setup menu
※Lens Initializing is strongly recommended at the first stage of setup menu control.
HOME POSITION
MOTION DEBLUR
EXIT
OFF
OFF
OFF
ON
ON
ON
SAVE&EXIT
PRIVACY
MOTION
TITLE SET
SMART IR
POINTING ZOOM
PRESET ZOOM
BLC/HLC
MENU V5.xx
EXT
10

Operating Instructions
17
NETWORK AF ZOOM CAMERA
Direct Control on Web-menu
SPECIAL DEFAULT DESCRIPTION
D-ZOOM(Digital zoom) is available up to 32x.
D-ZOOM starts working when the optical zoom reaches its
maximum tele-position. Zoom ratio is displayed on the right bottom
corner of the monitor if DISPLAY ZOOM RATIO is set to ON.
AUTO
FOCUS
ZOOM PUSH, AUTO and MANUAL modes are available for
zoom & focus.
MANUAL – Zoom in/out can only be adjusted by ▲,▼ of OSD
control joystick or Focus Near/Far button on WEB.
AUTO – Focusing is always working.
ZOOM PUSH – Focusing is activated only when zoom in/out is
working. It can be focused any area on video using by Near/Far
button on web. It works to make the target focus on video when
the focusing is not clear.
ZOOM
PUSH
Max.
D-ZOOM
OFF
EXPOSURE
MODE
AUTO Can set EXPOSURE MODE to AUTO, IRIS Priority, SHUT.
Priority, MANUAL and Flickerless
AUTO – Optimizes the video level by controlling the iris and the
shutter speed automatically.
SHUTTER. Priority - Selects to fix SHUTTER speed in a certain
speed and the video level is controlled by an automatic iris control.
This mode is useful when the color rolling occurs under the fluore-
scent lighting. It is not recommendable at outdoor in the daytime.
IRIS Priority – Selects to fix IRIS in a certain aperture and the
video level is controlled by an automatic shutter control. IRIS
Level menu is activated when EXPOSURE MODE is set to IRIS
Priority. Lower IRIS LEVEL will close more Iris and increase the
field of depth in the daytime but significantly decrease the low
light performance. Too much low IRIS LEVEL will result in the
foggy video by the diffusion from the lens iris.
MANUAL – Iris and Shutter can be set to fix.
Flickerless – Reduces the flicker in video when US(60Hz) / EU
(50Hz) mode is used in 50Hz/60Hz fluorescent lighting respectively.
SHUT. Priority, MANUAL and Flickerless modes disable
SENS-UP and MOTION BLUR functions.
BRIGHTNESS
Day:10
Night: 8 Adjusts the brightness of video. (0~20)
COLOR GAIN
Day:10
Night: 10
Adjusts the color level of video. (0~15) It can only be adjusted to
be set to COLOR D/N mode in Day & Night function.
GAMMA 0.55 Adjusts the gamma of video. (0.45 ~0.75)

Operating Instructions
18
NETWORK AF ZOOM CAMERA
SENS-UP AUTO
AUTO – SENS-UP is enabled or disabled automatically by the
scene brightness.
OFF – Disables SENS-UP
WDR OFF
WDR
Weight
MID
Improves the visibility for the high bright area and the dark area
by the double captures of image with LONG and SHORT exposures.
※CVBS video signal - Connecting 2nd video to CVBS port
disables WDR function temporary. It should be considered when
installer adjusts the video with installation monitor via CVBS
video signal
WDR level can be selected from LOW, MID and HIGH.
Care should be taken to select this mode because video may
lose its quality in some environments by the over compensation.
BLC
(Back Light
Compensation)
ON – Improves the visibility for the dark object by the bright back
light. Outside area of BLC window be can over saturated.
Available to set BLC POSITION at ADVANCED CAMERA MENU>
BLC/HLC>BLC POSITION
HLC – Cuts out the highlight area with black mask and excludes
it from compensation. Lower HLC LEVEL cut out video from the
lower level. HLC LEVEL is adjustable at ADVANCED CAMERA
MENU>BLC/HLC>HLC LEVEL
OFF
3D-NR 3D-NR is a very sophisticated and powerful time-based noise
reduction technology by monitoring the noise for the several video
frames and defining and eliminating them consecutively at low light.
Higher setting reduces noise much more but results in losing
the sharpness and the tail effect or the motion blur for the fast
moving target at low light.
MID
DAY&NIGHT EXT
for
IR LED
type
COLOR – Forcibly DAY/NIGHT is disabled and outputs color video.
AUTO – Used when DAY or NIGHT is determined by light level
through the lens and DAY from/to NIGHT is switched automatically
by the scene brightness.
When EXPOSURE>AGC is less than 12, DAY/NIGHT AUTO is
disabled and forcibly switches to _(DAY) to avoid the malfunction.
EXT, B/W(NIGHT) and COLOR(DAY) is independent on AGC
The brighter video can be obtained by increasing the exposure
time in the night with SENS-UP. SENS-UP is the maximum
integrations of frame by DSS(Digital Slow Shutter) in the low light.
AGC 10 AGC amplifies the video gain for brighter video but noise and
white pixel accordingly.
AGC level less than 10 disables AUTO in DAY/NIGHT

Operating Instructions
19
NETWORK AF ZOOM CAMERA
AUTO
for
Non IR
type
DAY
for
Non TDN
type
EXT – DAY or NIGHT is determined by the built-in light photo
sensor. Camera with IR LED must be set to EXT.
COLOR D/N – Forcibly Color mode, optimized for night condition.
It is available to recognize colors of car, people and moving objects
even at night. Parameters can be controllable & programmable
according to circumstance. Application for bright circumstance at
night such as downtown, civic area, street, mall and etc.
Day & Night
Threshold
Day & Night
GAP
10
MID
10
WHITE
BALANCE
MODE
WB Manual
R-Gain/
B-Gain
ATW
D↔N Threshold is a threshold level and Gap to switch from
DAY to NIGHT. (0~20)
Low makes camera entered NIGHT at lower light level.
High makes camera exited NIGHT at brighter light level.
ATW, ONE PUSH and MANUAL are available for the white balance
modes.
ATW – White balance is continuously working along with the
color temperature changes in the range of 2,000K~8,500K.
ONE PUSH – White balance works only when ONE PUSH is
selected.
MANUAL – This mode can be used only when the color
temperature does not vary. White balance is fixed to the settings
by R_GAIN and B-GAIN
Activates when WHITE BALANCE is set to MANUAL.
Adjustable 0~20.
SHARPNESS 10 Adjusts the sharpness of video.
DAY&NIGHT
Conventional COLOR mode in NIGHT COLOR D/N mode in NIGHT
ATW-ext – White balance is continuously working along with the
color temperature changes in the range of 1,800K~11,000K.
level. When EXTERNAL IR LED is used with NON IR LED model,
please set to IR LED MODE ON.
B/W – Forcibly removes IR cut filter and switches to B/W
regardless of light level.
Sets the gap level switching from/to DAY(color) or NIGHT(B/W).

Operating Instructions
20
NETWORK AF ZOOM CAMERA
Reverses the video left and right and/or up and down by
MIRROR/FLIP.
No Mirror, No Flip : Normal display without mirroring or flipping
No Mirror, Flip : Video is reversed upside down.
Mirror, No Flip : Video is reversed left and right.
Mirror, Flip : Video is reversed left and right and upside down.
When the video is reversed by Ver. or HV, then the joystick
directions are reversed accordingly. This feature is very useful
when a camera is installed in upside down.
No Mirror,
No Flip
MIRROR /
FLIP
DEFOG OFF AUTO – Enhances the foggy video automatically according to
status of scene.
MANUAL –Sets to enhance the foggy video manually regardless
of status of scene
DEFOG
Weight
MID LEVEL – LOW, MID, HIGH
Video quality can be less in normal environments.
DISPLAY
Zoom Ratio
OFF ON enables to display the Zoom Ratio on the bottom right
corner. OZx.x appears during the optical zoom and DZx.x will
display by multiplying the optical zoom ratio and the actual digital
zoom ratio.
DISPLAY ID OFF
OFF
ON enables to display Camera ID on Monitor.
DISPLAY FOCUS
INDICATOR
ON
ON enables to display the Focus Indicator on Monitor
ON enables to display Camera Tittle on Monitor.
DISPLAY Tittle
AUTO
IR LED Control(AUTO/OFF) is available with IR LED model only.
If IR LED is set to OFF, IR LED will be turned OFF but DAY or
NIGHT is still determined by the built-in light photo sensor.
Lens initialization is necessary during the installation or the
regular operation to align the position data with the mechanical
positions whose lens elements may move and deviate from its
calibrated position by the shock or vibration, for example, during
the transportation.
LENS INIT checks the positions for zoom and focus at both of
the end positions and saves them for the references.
Lens initialization is automatically executed at power up.
IR LED
Control
LENS
INITIALIZE
[ CAUTION ]
It is strongly necessary to execute LENS INIT in cases below;
1) At the final step for the installation.
2) When focus becomes out of control by the shock or vibration.