Energetic Lighting MPL1014-LED2X30KY User manual

1
Model # MPL1014-LED2X30KY
Dual Head LED Work Light
Installation Instructions
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-492-6566.
Item Number Purchase Date
ATTACH YOUR RECEIPT HERE
www.energeticlighting.com
LIGHTING

CAUTION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
WARNING
Any changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
BE EXTREMELY CAREFUL WHEN USING THIS DEVICE. Improper use of this work light
can result in injury or death. Follow all safeguards stated in this manual in addition to
normal safety precautions in working with electrical devices. DO NOT attempt to service
this device.
-When using outdoor portable work lights, always follow basic safety precautions to
reduce the risk of electric shock and personal injury.
-Failure to observe the following safety rules may result in FIRE, ELECTRICAL SHOCK,
INJURY, or EXPOSURE TO EXCESSIVE ULTRAVIOLET RADIATION.
-Use only 3-wire UL Listed outdoor extension cords that have 3-prong grounded plugs and
grounded receptacles that accept the work light’s plug.
-Use only with an extension cord for outdoor use, such as with cord type SW, SW-A,
SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW,
SJTW-A, SJTOW, or SJTOW-A.
-This product contains chemicals, including lead, known to the state of California to cause
birth defects and other reproductive harm. Wash hands after handling or touching this
portable work light.
32
•
•
-
-
-
-
www.energeticlighting.com www.energeticlighting.com
PACKAGE CONTENTS
Part Item Name Qty.
ALight Fixtures 2
BStand 1
CHandle bar 1
DTripod 1
EHeight Extension Locks 2
Part Item Name Qty.
AA Handle bar screws 2
BB Junction box screw 1
CC Light head screws 2
B
E
AA
BB
CC
SAFETY INFORMATION
HARDWARE CONTENTS
C
D
A

To avoid electrical shock, do not use near water or in areas where water may accumulate.
Keep work light at least 16 ft. from pools or spas. Keep plugs dry. Use only Ground Fault
Circuit Interrupter (GFCI) protected receptacles when using this work light in wet or damp
locations. Receptacles are available with built-in GFCI protection and are to be used for this
measure of safety.
Always unplug work light and allow lamp head to cool.
Do not look directly at the lighted lamps to avoid eye injuries.
Always keep the work light away from any flammable materials.
Do not operate work light if it has a missing or damaged lens cover. Contact customer
service for a replacement. Read and follow all safety rules and operating instructions before
first use of this product.
-
-
-
-
-
4
www.energeticlighting.com
5
www.energeticlighting.com
AA
CC
SAFETY INFORMATION
INSTALLATION INSTRUCTIONS
OPERATING INSTRUCTIONS
B
B
C
Tripod Height Adjustment
The tripod height can be adjusted by releasing
the Height Extension Locks (E) and extending
the tripod to the desired height, then locking the
Height Extension Locks.
2
Tripod Leg Extension
To extend the Tripod legs, press the Tripod Leg
Lock Release Button (DD) and pull the Collar
Assembly (EE) down until the legs lock in place at
the bottom of the Tripod stand.
To return the legs to the folded position for
storage, press the Tripod Leg Lock Release
Button (DD) and pull the Collar Assembly (EE)
back up to the top.
Attaching and Releasing Light Head
on Tripod
a) To attach the Light Fixture with stand, align the
Lock Pin (FF) over the mounting hole of the
Tripod (D), push down firmly until the Light Fixture
clicks into place.
b) To release the Light Fixture and stand, squeeze
the Light Head Release Knobs (FF) together while
pulling the Light Fixture up and away from the
Tripod (D).
1
3
1. Attach the handle bar (C) to the stand (B) using two
handle bar screws (AA).
1
2. Install the two light fixture heads (A) to stand (B) using
the two light head screws (CC). Attach the junction
box to the handle bar using junction box screw (BB).
2
BB
A
E
DD
FF
EE
D

ON/OFF Switch
Each lamp has an on/off switch. Press the switch toward the “ | ” symbol to turn the lamp
on. Press the switch toward the “O” symbol to turn the lamp off. Always turn the work light
off before unplugging.
Adjusting the light direction
1. Adjust vertically by loosening the two vertical adjustment knobs (D) on each side of the
metal bracket located below the lamp head. Adjust the lamp head to the desired position
using the handle and retighten both knobs.
2. Adjust horizontally by loosening the lower twist knob on the metal bracket located below
the lamp head. Adjust the lamp head to the desired position using the handle and retighten
knob.
5
Your portable LED work light requires very little care and maintenance. Simply clean the lens,
lamp head and lamp stand regularly with a non-abrasive cleaner.
Warning: Always make sure the work light is unplugged and completely cool before
attempting to clean it.
OPERATING INSTRUCTIONS
Printed in China
www.energeticlighting.com
CARE AND MAINTENANCE
TROUBLESHOOTING
Problem Possible Solution Corrective Action
The work light comes on,
but the lights are
dimmed.
Improper voltage or power
supply. Use of an extension
cord longer than 49 in. can
reduce the voltage supplied
to the light and can cause
dimming. Use 14-gauge
(AWG) extension cord with a
cord length of less than 49
in.
The work light will only oper-
ate on standard household
120 V AC/60 Hz power. Have
power supply checked by a
qualified electrician.
WARRANTY
This fixture is warranted to perform free from defects for five years. If it fails to do so, you may
return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.