ENERGY SISTEM Linnker 7000 User manual

1
Index
1. A/C adaptor and 3 AAA batteries........................................................1
2. Turning on / Turning off the Linnker 7000 and the Audio Adaptor...….1
3. Function Keys..........................................................................……......1
THREE possible User Scenarios...............................................................3
I. Linnker 7000 paired with Bluetooth enabled (with A2DP and AVRCP
profile) Mobile Phone / PDA / MP3 Guide...........................………….….3
1.Pairing............................................................................……...............3
2.Listening to music...............................................................…...........4
II. Linnker 7000 paired with Stereo Audio Adaptor Guide........................4
1.Pairing................................................................................…….........5
2.Listening to music..............................................................……..........5
III. Linnker 7000 connected directly with Audio Device Guide..................6
1.Llistening to music...........................................................……............6
Accessories Table...........................................................................….......6
FCC Interference Statement.........................................................…..........7
A/C adaptor and 3 AAA batteries
Thank you for buying the new Linnker 7000 Bluetooth stereo speakers and,
or the Bluetooth Stereo Audio Adaptor. You can use the A/C power adaptor
to power up the Linnker 7000 directly or install 3 AAA dry batteries into the
Linnker 7000 to obtain the power.
Turning on / Turning off the Linnker 7000
To turn on the speaker, please switch the power ON/OFF switch (Key 2) to
the “I” position. To turn it off, please switch the power switch to the “O”
position.
Function Keys
1. Battery cover(Insert 3 AAA batteries).
2. Power ON/OFF switch.

2
3. DC power input socket(5VDC).
4. Audio input socket.
5. Backward switch (only applied to audio devices supporting A2DP and
AVRCP Profiles).
6. Bluetooth Volume Down switch.
7. Forward switch (only applied to audio devices supporting A2DP and
AVRCP Profiles).
8. Bluetooth ON/OFF/Pairing/Pause switch.
a) When Linnker 7000 is powered on, press and hold (about 2 seconds)
until Bluetooth LED flashes Green to turn Bluetooth ON.
b) When Linnker 7000 is powered on, press and hold (about 4 seconds)
until Bluetooth LED flashes Green and Red alternatively to enter into pairing
mode.
c) When Linnker 7000 is powered on, press and hold (about 4 seconds)
until Bluetooth LED turns red to turn Bluetooth OFF when playing.
d) Press it once when it is playing --- Pause
Press it again --- Resume play
9. Bluetooth Volume Up switch.
10. a) Bluetooth LED flashes Green -- Bluetooth is ON.

3
b) Bluetooth LED flashes Green and Red alternatively – Bluetooth enters
into Pairing mode
c) Bluetooth LED is red -- Bluetooth will be OFF
11. Power LED is Blue -- Linnker 7000 is Power ON.

 !"##"$%
When you purchase a Standalone pack with Linnker 7000 only, please
follow this Guide.
1. Pairing
a. While the Speaker is powered off, switch the power ON/OFF switch (Key
2) to the “I” position to turn it on (Fig.1). The Power LED (Fig.3) will
become blue. Press and hold ON/OFF/Pairing/Pause switch (Key 8, Fig.2)
for 4 seconds, the Bluetooth LED will flash red and green alternatively,
which indicates the Speaker in Pairing Mode. The Pairing Mode will last for
one minute.
b. Put the Speaker and the Bluetooth enabled (with A2DP and AVRCP
profiles) Mobile Phone / PDA / MP3 close to each other, 0.5 to 3 meters.
c. Follow the operation instructions of your Bluetooth enabled (with A2DP
and AVRCP profiles) Mobile Phone/ PDA / MP3 to start the pairing process.
Typically, this has to be done by going to a setup or connect menu to
discover the Speaker. It may take some time to search it depending on the
number of Bluetooth devices nearby.

4
d. Your Mobile Phone / PDA / MP3 will display the model name “Linnker
7000” if it has found the Speaker; and ask for a passkey. Enter a sequence
of “0000”. After successful pairing, follow the instructions to establish the
Bluetooth connection with the Speaker.
e. If the pairing is successful, the Bluetooth LED will flash green, which
indicates it is in Standby Mode and ready to receive audio signals from the
Mobile Phone / PDA / MP3. If pairing does not occur as expected, turn the
Linnker 7000 and the audio device off. Wait for 10 seconds and repeat the
pairing process from the beginning (Fig.4).
2. Listening to music
a. Play the music on the Mobile Phone / PDA / MP3 as normal; you will
listen to the music from the Speaker.
b. The speaker volume can be adjusted by pressing the VOL Up button
(Fig.2) / VOL Down button (Fig.2).
c. While listening to music (for example, song 2), press the Speaker’s
FORWARD >> button (Fig.2) will skip to next song (for example, song 3);
press the BACKWARD << button (Fig.2) will replay the current song (for
example, song 2). The fast forward & backward are also supported by
holding the FORWARD >> or BACKWARD << function keys. This remote
control function is supported only by the AVRCP profile in your Bluetooth
enabled devices.
d. Turn the Speaker off after use.
Remark: Details operation of music playing through Bluetooth A2DP profile
varies from different Mobile Phones / PDAs
.
&&'%
When you purchase a Combo pack with Linnker 7000 and a stereo audio
Adaptor, please follow this Guide.

5
1. Pairing
a. While the Speaker is powered off, switch the power ON/OFF switch (Key
2) to the “I” position to turn it on (Fig.1). The Power LED (Fig.3) will be blue.
Press and hold Bluetooth ON/OFF/Pairing/Pause switch (Fig.2) for 4
seconds, the Bluetooth LED will flash red and green alternatively, which
indicates the Speaker in Pairing Mode. The Pairing Mode will last for one
minute.
b. While the Stereo Audio Adaptor is powered off, press and hold PLAY
and STOP buttons simultaneously. The LED will flash red and green
alternatively, which indicates the Audio Adaptor is in Pairing Mode. The
Paring Mode will last for one minute.
c. Put the Speaker and the Audio Adaptor close to each other, 0.5 to 3
meters. After a few seconds, their LED's on two devices will turn into
flashing green, which indicates successful pairing. Both units are in
Standby Mode and ready to transmit audio signal, or music from the
audio source (Fig.5).
2. Listening to music
a. After successful pairing, plug the jack of the Audio Adaptor to the 3.5
mm socket of any audio source such as iPod, MP3, CD player, Notebook
PC, or other audio devices with audio jack.
b. Play the music on the audio source as normal; you will listen to the
stereo music from the speaker.
c. The Music volume can only be adjusted by pressing and
releasing the VOL+ / VOL - buttons of audio source.
d. Turn the Speaker off after use and the Audio Adaptor will be turned off
automatically. Next time, you don’t need to pair them again. Turn

6
them on, and then they will be paired automatically and ready to
transmit music from the audio source.
&&&((()*(%
1. Listening to music
a. While the Speaker is powered off, switch the power ON/OFF switch (Key
2) to the “I” position to turn it on (Fig.1). The Power LED (Fig.3) will become
blue.
b. Plug one end of the audio cable to the “Audio input socket” (socket 4,
Fig.1) of the Linnker 7000 and the other end to the 3.5 mm socket of any
audio source such as iPod, MP3, CD player, Notebook PC or other audio
devices.
c. Play the music on the audio source as normal; you will listen to the stereo
music from the speaker.
d. The Music volume can only be adjusted by pressing and releasing the
VOL + / VOL- buttons of audio source.
e. Turn the Speaker off after use.
Accessories Table
1. Audio cable.
2. AC/DC Adaptor.
3. 3 x AAA Batteries

7
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference To radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:

8
This equipment complies With FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Remarks: Specification of A/C power adaptor for Linnker 7000
DC Voltage input: 5V, 500mA
DC plug: (1.35 X 3.5 X 11) mm