enertik BS-550-SLA User manual

Solar Pumping Inverter
User’s Manual

Preface
In order to give full play to the product performance and guarantee the safety of user and
equipment, before installation and use, please carefully read the manual.
In order to facilitate daily inspection and maintenance of inverter and understand abnormal
reason and solutions, please keep the instruction properly.
If you have any questions or special requirements during use, please contact with our
company’s product dealer or directly contact with our company’s technical service center.
If the manual contents change, we may not offer notice.

Operation Instruction of BS Series SolarPumping Inverter Precautions
I
Contents
Precautions................................................................................................................................II
Chapter I Product Introduction............................................................................................1
1.1 Introduction toSolarPumping System................................................................................1
1.2 Product Characteristics........................................................................................................2
1.3 Inverter Specification...........................................................................................................3
Chapter II Installation and Wiring..........................................................................................7
2.1 Procurement Inspection.......................................................................................................7
2.2 Dimension and Weight.........................................................................................................7
2.3 Installation Diagram............................................................................................................9
2.4 Wiring Diagram.................................................................................................................10
2.5 Assemble DC Connector....................................................................................................17
2.6 Introduction to the Wiring of Water Level Sensor.............................................................17
Chapter III Operation Control...............................................................................................20
3.1 Panel Layout and Introduction...........................................................................................20
3.2 Panel Operation Method....................................................................................................21
3.3 Work Mode........................................................................................................................23
3.4 Introduction to the Procedure of Wiring and Debugging..................................................23
Chapter IV: Failure Diagnosis................................................................................................32
4.1 Explanation and Solution for Fault Code..........................................................................32
Chapter V Maintenance...........................................................................................................34
5.1 Daily Inspection and Maintenance....................................................................................34
5.2 Inspection and Replacement of Quick-wear Parts.............................................................35
5.3 Storage and Maintenance...................................................................................................35
Quality Assurance....................................................................................................................38
Warranty Card.........................................................................¡Error! Marcador no definido.

Operation Instruction of BS Series SolarPumping Inverter Precautions
II
Precautions
The safe operation of the product is subject to correct transportation, installation, operation,
and maintenance. Before conducting these tasks, please pay attention to relevant safety instructions.
The warnings related to safety in the manual are listed as follows:
Grounding Wire of Equipment
AC Value
DC Value
Phase
Before operating inverter, please read the instruction.
5minutes
In order to avoid electric shock, breack off machine with PVterminal and
AC terminal for at least 5 minutes, then contact the wire of machine output
terminal and input terminal
Warning: when machine works, the temperature of metal shell may be
very high.
Procurement Inspection
Warning
1. If the inverter isfound to suffer damage or lack in component and part, do not
install it, or else it may cause accident!
Installation
Warning
1. In order to guarantee good effect of convection cooling, the inverter shall be
installed vertically. Keep at least 10cm space between upward side and downward
side.

Operation Instruction of BS Series SolarPumping Inverter Precautions
III
2. Try to install it in the indoor place with ventilation opening or air interchanger. It is
forbidden to install it directly under sunshine.
3. During installation, do not discard residue of drill hole into inverter cooling find or
fan, which may affect heat dissipation.
Wiring
Danger
1. The wiring shall be conducted by qualified electric technician, or it may cause
electric shock or fire disaster.
2. Before wiring, please confirm that the input power has been cut off, or else it may
cause electric shock or fire disaster.
3. The grounding terminal must be grounded reliably, or else the inverter shell may
have electricity.
4. Thesolar array, motorload, and inverter model selection shall be reasonable, or
else it may damage equipment.
Warning
1. Please use specified moment of force to tighten terminal, or else it may cause fire
disaster.
2. Do not connect capacitance or phase advance LC/RC noise filter in the output end
of inverter. When the distance between inverter and motor load is over 100m, it is
advised to use output reactor.
Operation
Danger
1. Power on after confirming that the wiring is correct, or it may damage inverter or
fire disaster.
2. During electricity, do not change wiring, or else it may cause electric shock.

Operation Instruction of BS Series SolarPumping Inverter Precautions
IV
Warning
1. Before the first operation, please adjust some control parameters according to
operation instruction. Do not alter the control parameters of inverter at random, or
else it may damage the equipment.
2. During operation, the temperature of radiator is very high. Do not touch the
radiator, or else it may scald you.
3. When height above sea level exceeds 1000m, the inverter shall be used under rated
power. If the height increases by 1500m, the output current shall decreases by 10%.
Miscellaneous
Danger
1. Assign qualified electric technician for maintenance and inspection.
2. During power-up state, do not remove the inverter. After outage, wait for 5 minutes
at least, then conduct maintenance and inspection, so as to avoid that the residual
voltage on electrolytic capacitor of major loop may cause damage to people.
3. It is forbidden to transform the inverter without authorization, or else it may
damage personnel or equipment.
4. When handling scrapped inverter, please dispose the inverter as industrial waste.
The inner electrolytic capacitor may explode during burning. Some components and
parts may generate hazardous and harmful gas during combustion.

Operation Instruction of BSSeries Solar Pumping Inverter Product Introduction
1
Chapter I Product Introduction
1.1 Introduction toSolarPumping System
Solar Pumping System is widely applied in domestic water, agricultural irrigation, forestry
watering, desert control, grassland animal husbandry, island water supply, water treatment project,
etc. During recent years with the enhancement of new energy utilization, solarpumping system is
widely applied in the landscape and water spray system of municipal works, urban square, garden
sightseeing, tourist resort, hotel, and residential community. The system consists of solar cell array,
pumping inverter, and waterpump(figure 1-1). Based on the design philosophy of saving water first,
the system omits energy storing device such as accumulator.
Figure 1-1 Structure ofSolarPumping System
The solar cell array is made fromthe series connection and parallel connection of several solar
cell modules, which absorb solar radiation energy and transform it into electric energy, so as to
supply electric power for the whole system. The pumping inverter controls and regulates the
operation of the system, transforms the direct current of solar cell array into alternating current to
drive water pump. In addition, according to the change of sunlight intensity, regulate output
frequency timely, to realize MPPT (Maximum Power Point Tracking). The water pump is driven by
Single-phase AC motor. It pumps water from deep well, river, and lake, then inject water into water
storage tank/pool, or directly connect with irrigation system or fountain system, etc. According to
actual requirements ofsystem and installation, different types of water pumps such as centrifugal
pump, axial flow pump, mixed-flow pump, or deep-well pump can be used.
DC Voltage Single-PhaseAC Voltage

Operation Instruction of BSSeries Solar Pumping Inverter Product Introduction
2
1.2 Product Characteristics
On the basis of many-year research, development, and experiment, the pumpinginverter
(Figure 1-2) independently developed and produced by our company has the following advantages:
Use independently-developed dynamic VI MPPT (Maximum Power Point Tracking)
control method. The response speed is fast. Operation is stable and reliable. It solves the
following problems: tracking effect is poor when sunlight intensity rapidly; operation is not
stable; water hammer damage.
All digital control. It has complete automatic operation, data storage, and complete
protection functions.
SolarPumping Inverter is specially designed forsolar water pump. The inner structure is
more reasonable and professional.
All key parts used insolarpumping inverter are made by international famous brands. The
quality is reliable, service life is long, and quality assurance period is long.
Component
and Part Manufacturer Country
IGBT Module Infineon Germany
Electrolytic
Capacitor NCC Japan
EMI Filter VAC Germany
DSP Control
Chip TI America
PV Fuse BUSSMAN America
The shell ofsolar pumping inverter is thick. The design process is improved through
abrasive tool test for many times. The appearance is elegant and exquisite, model is
compact, and weight is proper.
solarpumping inverter integrates combiner box. It includes DC switch,lightning arrester,
fuse, and optional components. It greatly simplifies and facilitates equipment installation
and maintenance, but also effectively protects the equipment.
Multiple communication interfaces such as RS485/CAN/GPRS(optional), etc. User can
check or control the running status and running mode of the system in a remote place.
The design ofsolarpumping inverter selects electric supply or diesel generator as standby
inverter power supply, so as to meet the comprehensive requirements of watersupply.
solar pumping inverter has complete operation protection mechanisms, including output
short circuit protection, IGBT module overcurrent protection,
acceleration/deceleration/constant speed overcurrent protection,
acceleration/deceleration/constant speed overvoltage protection, input
overvoltage/undervoltage protection, motor overload protection,inverter overload

Operation Instruction of BSSeries Solar Pumping Inverter Product Introduction
3
protection, output side phase loss protection, inverter module overheat protection,
grounding short circuit protection, and underload (anti-dry pumping) protection.
The main circuit uses power module (PIM), and the reliability is higher.
The small-power model uses completely-new aluminum shell, LCD display operation
panel, and directly-insert connection terminal. The appearance is beautiful. The heat
dissipation effect and protective properties are good.
Upper and lower water level detection and control circuit are optional.
Protection grade IP65, temperature of service environment:-10 ~ +50˚C.
Figure 1-2 BS Series Pumping Inverter
1.3 Inverter Specification
1.3.1 Introduction to Nameplate and Model
The product nameplate is located at the right lower part of inverter. The nameplate includes
important information such as product series,voltage, power grade, software version, and hardware
version. Such information provides important basis for product application, maintenance, and
after-sales service.

Operation Instruction of BSSeries Solar Pumping Inverter Product Introduction
4
Figure 1-3 Introduction to Product Nameplate and Model
Identification Introduction
1Product Series
2Rated Power (W) of Motor
3S: Single Phase
4Output Voltage (L: 220V)
5 A: with electric supply function None: without electric supply
function
Warning: do not rip out product nameplate label.

Operation Instruction of BSSeries Solar Pumping Inverter Product Introduction
5
1.3.2 Product Specification and Technical Index
Model
Max.
DC input
voltage
(Vdc)
Recommen
ded MPP
voltage
(Vdc)
Start
voltage
(Vdc)
Rated
output
power（W）
Max.AC
output
current（A）
Output
frequency
（Hz)
Rated output
voltage（Vac）
BS-550-SL 450 100-400 80 400 4 0-50/60 1PH 220V
BS-550-SL
A
450 100-400 80 400 4 0-50/60 1PH 220V
BS-750-SL 450 150-400 120 750 6.3 0-50/60 1PH 220V
BS-750-SL
A
450 150-400 120 750 6.3 0-50/60 1PH 220V
BS-1100-S
L
450 150-400 120 1100 8.6 0-50/60 1PH 220V
BS-1100-S
LA
450 150-400 120 1100 8.6 0-50/60 1PH 220V
BS-1500-S
L
500 200-400 120 1500 10 0-50/60 1PH 220V
BS-1500-S
LA
500 200-400 120 1500 10 0-50/60 1PH 220V
BS-2200-S
L
500 280-400 200 2200 14 0-50/60 1PH 220V

Operation Instruction of BSSeries Solar Pumping Inverter Product Introduction
6
BS-2200-S
LA
500 280-400 200 2200 14 0-50/60 1PH 220V
Warning: please select appropriate model according tosolarcell array and motor load.
Warning: The input power in the above table refers to multi-channel total input power. The
maximum input DC current of each group shall not exceed 15A.

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
7
Chapter II Installation and Wiring
2.1 Procurement Inspection
Our company has strict quality assurance system in aspects of product manufacturing,
packaging, etc. In case of abnormal condition, please contact withour company’s product dealer, or
contact with our company’s technical service center. We will provide you with solution as soon as
possible. When you get the products, please confirm the following items:
Inspection Item Inspection Method
Whether it accords with ordered products Inspect nameplate of product
Whether it is damaged or falls off Check the overall appearance
Whether host computer and parts are complete Inspect according to product checklist
Whether tightening parts such as bolt are loosened When necessary, use screwdriver for inspection
2.2 Dimension and Weight
Figure 2-1 Product Appearance and Installation Dimension

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
8
Product Specification Parameter:
Model Weight（Kg）
Appearance and installation dimension (mm)
L W H
BS-550-SL 5 418 288 152
BS-550-SLA 5 418 288 152
BS-750-SL 8 418 288 152
BS-750-SLA 8 418 288 152
BS-1100-SL 8 418 288 152
BS-1100-SLA 8 418 288 152
BS-1500-SL 10 453 288 152
BS-1500-SLA 10 453 288 152
BS-2200-SL 10 453 288 152
BS-2200-SLA 10 453 288 152
Warning: most models ofBSseries are hanging installation. Guarantee that the installation
backboard can bear the weight of inverter.

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
9
2.3 Installation Diagram
Figure 2-2 Installation Dimension ofBS-550-SL/SLA to 2200-SL/SLA
Figure 2-3 InstallSafety Nut

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
10
Figure 2-4 Correct Arrangement Diagram of Inverter
2.4 Wiring Diagram
2.4.1 Introduction to Crate Socket
Figure 2-5 BS-550-SL/SLA to 1100-SL/SLA Wiring Terminal
Figure 2-6 BS-1500-SL/SLA to 2200-SL/SLA Wiring Terminal
PV Input Terminal
AC Input Terminal
AC Output Terminal
Water Level Terminal

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
11
2.4.2 Wiring Diagram of Two-Wire Water Pump
Figure 2-7 BS-550-SL to 1100-SL Wiring Diagram
Figure 2-8 BS-550-SLA to 1100-SLA Wiring Diagram

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
12
Figure 2-9 BS-550-SL/SLA to 1100-SL /SLA Wiring Diagram
2.4.3 Wiring Diagram of Three-Wire Water Pump
Figure 2-10 BS-1500-SL to 2200-SL Wiring Diagram

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
13
Figure 2-11 BS-1500-SLA to 2200-SLA Wiring Diagram
Figure 2-12 BS-1500-SL/SLA to2200-SL/SLA Wiring Diagrams
Use key to open the lower cover of crate. There is DC switch, water level sensor connection
terminal, GPRS (optional), and AC output terminal.

Operation Instruction of BS Series Solar Pumping Inverter Installation and Wiring
14
Figure 2-13 A/O Terminal Diagram
Figure 2-14 I/O Terminal Diagram
Analog
Output
Analog
Output
Relay 1 Output
Relay 2 Output