ENFORCER EV-Y6201-A3WQ User manual

EV-Y6201-A3WQ
4-in-1 HD TVI, CVI, AHD, Analog
UFO Camera
Manual
•Select between multiple formats:
TVI, CVI, AHD, and Analog
•
1080p Resolution
•
3.7mm Pinhole lens rotates to nearly any
angle for flexible installations
•
3D-NR (3D Digital Noise Reduction)
•
DWDR (Digital Wide Dynamic Range)
•Low 0.1Lux rating
•
1/2.9" 2MP Sony CMOS
•
Heavy-duty vandal-resistant design
•
Rugged, weatherproof (IP66) construction
•
Small size protrudes only 1" (26mm)
•
Low-profile design blends in with nearly
any decor
Features:

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog UFO Camera
2SECO-LARM U.S.A., Inc.
Specifications:
Model
EV-Y6201-A3WQ
Type
Flush-Mount UFO Camera
Formats
TVI (Default) / CVI / AHD / Analog
CMOS
1
/2.9" 2MP Sony CMOS
Resolution (HD)
1920x1080
TV Lines (Analog)
1200TVL
2D-NR
Yes
3D-NR
Yes
DWDR
Yes
OSD (On-Screen Display)
Yes
Cable OSD control
Yes
Video output
1.0Vp-p Complex video output
Megapixels
2MP
Lens
3.7mm Pinhole lens
Viewing angle
80°
FPS
30FPS
F Stop
F1.4
Minimum illumination
0.1Lux
Gamma correction
0-1
S/N Ratio
50dB
DSS (Digital Show Shutter)
Yes
Shutter control
Auto/Manual (x30~1/50000), FLK
Gain control
Yes
White balance
Auto, Day & Night
Operating voltage
12VDC
Current draw
90mA
IP Rating
IP66
Operating temperature
-4°~131° F (-20°~55° C)
Dimensions
3"x3"x1" (77x77x26 mm) (Protruding from wall)
Weight
9.9-oz (280g)
Parts List:
Dimensions:
1x
UFO Camera
1x
Base
3x
Mounting screws
1x
Flange
1x
Ring bracket
1x
DC Plug with terminal block
Flange
Camera ball
Base
Assembled camera
3"
(77mm)
115/
16
"
(49mm)
213/
16
"
(72mm)
21/
4
"
(56mm)
1"
(26mm)
3" (77mm)

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog UFO Camera
SECO-LARM U.S.A., Inc. 3
Overview:
Before Starting:
Installation:
Important:Do not cut any wires as the warranty willbe voided.
1. Use the camera within the given temperature
and voltage limits.
2. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
3. Do not subject the camera to strong vibrations.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
1. Run a 12VDC power supply wire and a video
cable with a male BNC connector to the wall or
ceiling where the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC
connector.
4. While watching the monitor, hold the camera
against the wall or ceiling by hand where it is to be
mounted, then turn the camera until it is certain
that this mounting location is correct. Use a pencil
to mark the location.
5. Disconnect the power supply and video cable.
6. Cut or drill a 21/16”(52mm) hole in the ceiling or
wall where the camera is to be mounted.
7. Twist the flange off the base and remove the
camera ball.
8. Place the ring bracket behind the hole.
NOTE: Ring bracket is not necessary if
surface-mounted.
9. Push the base into the hole, and secure to the ring
bracket using the three supplied mounting screws.
10. Run the power supply and video cable through the
wall or ceiling to the hole, and through the bracket
and base. Connect to the camera’s power and
video connectors.
11. Hold the ball in the base, and secure with the
flange. Secure the flange partially, leaving room to
adjust the angle of the lens.
12. Use the OSD controller's joystick to adjust camera
settings (see the separate OSD manual).
13. Apply the power to the camera. Watch the monitor
and adjust the angle of the lens.
14. Secure the camera by tightening the flange.
15. Do a final test of the video camera and monitor.
Surface-Mount Installation:
Requires the EV-6640SWQ (Sold Separately)
Standard Installation:
Surface-mount
bracket
Run the power and
video cablesthrough
the wall oron surface
OSD Controller Settings:
To setformat via the OSD controller, press the
controller in the direction of
thedesired setting,
hold for 5 seconds,and rel
ease when the
camera restarts.
See chart below.
For the full
OSD manual visit:
www.
SECO-LARM.com.
Direction
Format Setting
Up
CVI
Down
TVI
Left
CVBS
Right
AHD
UP
DC Plugwith
terminal block
Flange
Camera
Ball
Mounting
screws x3
Ring bracket
(inside ceiling/wall)
Base
OSD controller
DC Jack
Female BNC
Connector
Wall
or
Ceiling
Wall
or
Ceiling

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog UFO Camera
4SECO-LARM U.S.A., Inc.
The screen is blank.
•Check that the camera is powered up.
•Check that the power supply's polarity is correct.
•Check that the monitor is powered up.
•Check that the video cable connecting the camera to the monitor is
connected properly.
The screen image is dim.
•Clean the lens using a soft, clean cloth.
•Check that the light source is adequate.
The screen image has poor
contrast.
•Adjust the monitor's contrast knob.
•Change the position of the camera.
The screen image flickers.
•Change the position of the camera, check cables and format setting.
The screen image is distorted.
•Change the position of the camera, check cables and format setting.
The camera case is hot.
•Check that the correct power supply is in use.
®
PICSN4
MI_EV-Y6201-A3WQ_161020a.docx
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
will not be
held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS
DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes ormodifications notexpresslyapproved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no chan
ge to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
SECO-LARM
®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: [phone] | [phone]
Email: [e-mail]
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2016SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whol
e or
in part, without the written permission of SECO-LARM.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date ofsale to the originalcustomer. SECO-
LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determi
nes that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’
s
option. In no event shall SECO-
LARM be liable forany special, collateral, incidental, or consequential personal orproperty
damage of any kind to the purchaseror anyone else.
Troubleshooting:
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as itcould cause fire orelectric
shock.
Do not open the case of thisdevice, asthere are no user-serviceable components inside.
Do not cut
any wires as thewarranty will be voided.
Surface-mounting allows for a quick and easy installation while
maintaining a low
-profile appearance.
Diameter: 4
5/16” (109mm)
Height (with camera): 2
3/8" (60mm)
Optional Surface-Mount Bracket (Sold separately):
EV-6640SWQ