ENFORCER EV-1223C12 User manual

ENFORCER CCD DOME CAMERA Manual ENFORCER CCD DOME CAMERA Manual
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws
and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use
of this product in violation of any current laws or statutes.
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®®
®®
®
• Check that the dome camera is powered up.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is connected properly.
• Clean the lens (using a soft, clean cloth).
• Check that the light source is adequate.
• Clean the dome (using a soft, clean cloth).
• Adjust the monitor’s contrast knob.
• Change the position of the camera
• Change the position of the camera
• Change the position of the camera
• Check that the correct power supply is in use.
The screen is blank
The screen image is dim
The screen image has poor contrast
The screen image flickers
The screen image is distorted
The camera case is hot
TROUBLE SHOOTING
1/3" CCD B/W Dome Camera
Video
Format
Model
Number
Lens
Size
Viewing*
Angle
EV-122B-4
EV-125B-4
EIA
CCIR
4.3mm
4.3mm
78o
78o
*All viewing angles are approximate
1/3" CCD Color Dome Camera
Video
Format
Model
Number
Lens
Size
Viewing*
Angle
EV-1223C12
EV-122C-2
EV-1253C12
EV-125C-2
NTSC
NTSC
PAL
PAL
4.3mm
2.9mm
4.3mm
2.9mm
78o
120o
78o
120o
MANUAL
WARNING
!Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or electric shock. Do not modify this
device, as there are no field-serviceable components inside.
!
This product was designed for indoor use only. Mounting outdoors or exposure to rain or moisture could cause a dangerous electric shock,
damage the device, and void the warranty. Do not modify this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
File:DT/DTP/MiEV1223C12_06B.PMD
PITNW1
®
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®U.S.A., Inc.U.S.A., Inc.
U.S.A., Inc.U.S.A., Inc.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco-larm.com
E-mail: sales
@ seco-larm.com
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2006 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair
or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any
kind to the purchaser or anyone else.
Now with Multi-Axis
Gimbal Bracket
ENFORCER
VIDEO
®

ENFORCER CCD DOME CAMERA Manual ENFORCER CCD DOME CAMERA Manual
Parts List: 1 x Dome camera
4 x Mounting screws
4 x Drywall anchors
1 x Manual
Focus
Lock Screw
Dome
Base
DC Jack
BNC(F) Connector
Support Bracket
INSTALLATION
1. Remove the dome. Be careful not to scratch the dome. DO
NOT TOUCH ANY OF THE COMPONENTS INSIDE THE DOME.
2. Connect the camera to a video monitor via the video cable.
3. Temporarily connect the camera to a 12VDC power source.
Do not cut the power jack or video jack, as warranty will
be voided.
4. Hold the base of the dome camera with your hand against the
ceiling, and try various locations and angles while watching
the video monitor to find the location which offers the best
protection. Mark that location with a pencil.
Note:The ENFORCER dome camera is equipped with multi-axis
Gimbal bracket which will make it applicable for both wall and
ceiling.
5. For wall-mounting applications —Take out the 2 screws and
turn the lens 90o clockwise until the wire harness is adjacent
to the mounting bracket. Replace the 2 screws to
secure it. See Fig. 1.
6. Run a hidden, permanent video cable from the monitor
to the mounting location.
7. Run a hidden cable from a 12VDC power supply to the
mounting location.
8. Connect the two cables to the dome camera.
9. Mount the base to the ceiling at the selected location
with the four mounting screws.
10. Make any necessary adjustments to the horizontal and
vertical angles of the camera itself while checking the
image in the video monitor.
11. Replace the dome, taking care not to touch the camera
or scratch the dome.
12. Test the camera again under the exact lighting
conditions under which it is expected to be used.
31 /2” (88mm)
SIDE VIEW BOTTOM VIEW
21/4” (57mm)
31 /2” (88mm)
Important:
Do not cut DC jack. Use
SECO-LARM’s optional
EVA-F5521-3 Pigtail Connector for
easy installation and serviceability.
Lens
Wire harness
BEFORE STARTING
1. This product was designed for indoor use only. Do not mount
the CCTV camera where it is exposed to rain or other moisture,
or in humid or dusty places.
2. Do not point the CCTV camera at the sun. Heat could damage
the camera, even when not in use.
3. Do not mount the CCTV camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.*
4. Do not disassemble the lens or circuit board. There are
no user-serviceable parts inside.
5. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromag-
netic fields close to the display CRT, especially when the
monitor is turned on or during de-Gaussing, which
occurs automatically with many monitors when the
monitor is turned on.
Window
Camera
Dimensions:
EV-122B-4 (EIA)
EV-125B-4 (CCIR)
B/W camera
1/3” CCD, A1 PROs
N/A
EV-1223C12 (NTSC)
EV-122C-2 (NTSC)
EV-1253C12 (PAL)
EV-125C-2 (PAL)
Color camera
1/3” CCD, Sony
AWB
110mA
Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
Viewing Angle*
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Gain control
White Balance
D/A Bits
Power source
Power consumption
Operating temperature
Dimensions
Specifications
420 TV lines
512 x 492 pixels (NTSC / EIA)
512 x 582 pixels (PAL / CCIR)
2:1 interlace
Internal
1V pp composite output, 75 ohms
EV-1223C12 / EV-122B-4 (4.3mm)
EV-1253C12 / EV-125B-4 (4.3mm)
EV-122C-2 / EV-125C-2 (2.9mm)
EV-1223C12 / EV-122B-4 (78o)
EV-1253C12 / EV-125B-4 (78o)
EV-122C-2 / EV-125C-2 (120o)
0.1 lux
0.45
>48dB (AGC off)
Auto Electronic Shutter (AES)
1/60~1/100,000 sec. (NTSC / EIA), 1/50~1/100,000 sec. (PAL / CCIR)
Auto & Manual
Auto
10
12VDC
14°~140° F (-10°~60° C)
31/2” x 21/4” (88 x 57 mm)
* All viewing angles are approximate
100mA
Screw
Wire
Harness
Screw
Support
Bracket
Support
Bracket
Support
Bracket
Wire
Harness
90oo
oo
o
Fig. 1 — For wall mounting. Remove the 2 screws and turn the lens 90oo
oo
oclockwise
until the wire harness is adjacent to the support bracket, then replace the 2 screws
to secure it.
Important:
Do not cut DC Jack or Video Jack
as warranty will be voided.
Lens