Englefield SORRENTO Series User manual

BEFORE YOU BEGIN
TOOLS & MATERIALS REQUIRED - (Not supplied)
1260050-A02-A
INSTALLATION
INSTRUCTIONS
ACCESSORIES
Englefield
SORRENTOTM
Accessory Range
If you are building a
bathroom from scratch,
giving your bathroom a
makeover or just
replacing an old tap,
Englefield can provide a
solution for you.
CONTACT AND WARRANTY INFORMATION
SPARE PARTS LIST
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
INSTALLATION INSTRUCTIONS SORRENTO
TM
Accessories
13/4/2015
Before proceeding with the installation, please read these instructions
carefully to familiarise yourself with the required tools and materials, and
to ensure proper care and installation of the accessory.
Prior to installation, inspect the accessory to ensure that no damage has
occurred in transit. If damage has occurred, or a visible defect exists, do
not proceed with installation, and advise your supplier immediately.
Please keep these instructions for future reference.
1. Do not install where the product might be used as a grab or support
bar.
2. Prior to drilling into walls, check there are no hidden electrical wires,
cables or water supply pipes with the aid of an electronic detector.
3. These accessories are designed to be mounted to a wall and it is
strongly recommended that the product is installed on a stud, noggin
or to concrete.
4. When mounting to a stud or noggin we recommend using an
electronic stud finder to locate studs before installation.
5. Wear safety glasses when drilling.
CAUTION
!
Englefield
2mm drill bit
6mm
tile/masonry
drill bit
#2 square driveStud finder
For warranty information, please visit our website.
Sorrento bracket - double post
1259737
For use with:
- Double towel rail
- Single towel rail
- Glass shelf
Sorrento fixing kit
1259738
Included components:
-2 x #2 square drive screws
-2 x wall plugs
-1 x 2.5mm hex key
Grub screw - M5 x 12mm
1262221
For use with all Sorrento accessories
Sorrento bracket - single post
1262464
For use with:
- Robe hook
- Hand towel ring
- Toilet roll holder

CLEANING INSTRUCTIONS
1. LOCATING AND MARKING
2. BRACKET INSTALLATION
Select an appropriate location to install the accessory.
It is strongly advised to install the product on a solid base,
and the use of an electronic stud finder is recommended for
stud/nog installation. (Fig. 1)
NOTE: Refer to assembled accessory for bracket alignment and
orientation.
•For accessories with one bracket
Use a level to ensure the bracket is positioned horizontally and
that it is correctly oriented with tapered holes facing you (Fig. 2).
Mark the location of the holes with a sharpened pencil.
•For accessories with two brackets
A hole location template is provided (Fig. 3). Select a location to
place the template. Use a level to ensure that the template is
horizontal. Ensure it is pressed flat and fix the template to the wall.
NOTE: When drilling holes make sure to do so as accurately as
possible.
Stud or a nog installation (Fig. 4)
•Pre-drill 2mm diameter pilot holes at the marked locations.
When using the installation template, drill directly through the
template on the marked locations, then remove the template.
•Align the bracket/s so that it is correctly oriented and secure the
bracket in place with the supplied screws using a #2 square drive.
•Ensure that the screws are firmly fastened.
Ceramic tile or concrete installation (Fig. 5)
•Drill 6mm diameter holes at the marked locations using a tungsten
carbide tipped drill bit for tiles, or a masonry bit for concrete.
•Gently tap the supplied toggles into the holes using a mallet until
they are fully inserted.
•Orient the bracket correctly over the wall plugs and ensure the
bracket is flush with the wall.
• Secure the bracket firmly in place with the supplied screws using a
#2 square drive.
Fig. 2
Page 3
Page 2
SORRENTO
TM
Accessories INSTALLATION INSTRUCTIONS SORRENTO
TM
Accessories INSTALLATION INSTRUCTIONS
3. ACCESSORY INSTALLATION
4. CHECK INSTALLATION
Clean accessories with mild soap and warm water. Wipe entire surface completely dry with a clean soft
cloth. Harsh cleaning products including those that contain ammonia and chlorine may adversely affect
the finish and are not recommended for cleaning.
Step 3.1
NOTE: For all accessories ensure that the grub screw hole is
oriented downwards.
•For the robe hook, toilet paper holder & hand towel
ring
Slide the accessory over the bracket. (Fig. 6)
•For the single towel rail, double towel rail & glass shelf
Slide the assembled accessory over the fixed brackets.
(Fig. 7)
Step 3.2
Align and firmly press the accessory against the wall
while screwing in the grub screw/s with the provided
hex key. Make sure the grub screw/s are firmly tightened.
Fig. 4
Fig. 5
Ensure that all connections are tight. Place glass components onto appropriate accessories.
ENGLEFIELD
ENGLEFIELD
Template
!
Fig. 3
Fig. 1
Fig. 6
Fig. 7
Plaster board installation
Please consult your local hardware store for appropriate wall plugs for installation on plaster board.