Whittier Wood McKenzie Alder 1614a User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 07/17
McKenzie Alder
Hutch
Finished Program
Assembly Instructions
Model #
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb, sit or stand on this piece of furniture.
•Do not overload the shelves.
•Unload items before you move this unit.
•Before you begin your project, completely read the Assembly
Instructions.
•This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use
of tip-over restraints may only reduce but not eliminate the risk of tip-
over.
To help prevent tip-over:
•Place heaviest items in the bottom drawers.
•Unless specifically designed to accommodate, do not set TVs or
other heavy objects on top of this product.
•Never allow children to climb or hang on drawers, doors or shelves.
•Never open more than one drawer at a time.
•Do not defeat or remove the drawer interlock system.
Warning: At least one tipping restraint kit was included with your
piece of Whittier Wood Furniture. When you receive your furniture, be
sure to find and properly install the tipping restraint(s). If you cannot
locate the restraint(s), please contact us immediately for replacement.
Drilling, sawing, sanding or machining wood products can expose you
to wood dust, a substance known to the state of California to cause
cancer. Avoid inhaling wood dust or use a dust mask or other
safeguards for personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [e-mail]
1614a
McKenzie Alder
Hutch 24"W
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.
1620a
McKenzie Alder
Hutch 30"W
1626a
McKenzie Alder
Hutch 36"W
1632a
McKenzie Alder
Hutch 48"W

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Parts List
1614a_1620a_1626a_1632a_Finished — Page 2 — 07/17

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Parts List
1614a_1620a_1626a_1632a_Finished — Page 3 — 07/17
Before you begin to assemble this unit, identify each part and
make sure the quantities received match what is on this list.
If you need to replace a part, please refer to the following list for the finish, part name and letter code.
Bookcase Finish
Please note the finish of the bookcase for replacement part orders.
Bookcase finish options are subject to change.
Stain
Paint
Two-Tone
Part
Description
Quantity
1614a
1620a
1626a
1632a
A
Top Assembly
(attached)
1
1
1
1
Ba
Case
1
1
1
1
C
Adjustable Shelf (installed)
2
2
2
4
D
Lower Shelf (installed)
1
1
1
0
E
Left Lower Shelf (installed)
0
0
0
1
F
Right Lower Shelf (installed)
0
0
0
1
G
#6 x 1/2" Undercut Screw
(inserted)
8
8
8
16
R
#8 x 1" Pan Head Screw
(inserted)
8
8
10
10
I
#6 x 5/8" Philtruss Screw
(inserted)
8
8
8
9
J
#8 x 1-1/4" Pan Head Screw
2
2
2
2
K
#8 x 1-1/4" Black Screw
(inserted)
0
0
0
1
GAC
Glazed
Antique Cherry
SN
Snowbound
SW 7004
CAF
AW
FST
SL
HAZ
TB
Caffè
Snowbound
SW 7004
Natural Alder
Silverplate
SW 7649
Natural Alder
Aged White
SW 9180
Natural Alder
Tricorn Black
SW 6258
Natural Alder
NA
SNN
Fieldstone
Aged White
SW 9180
Silverplate
SW 7649
AWN SLN
TBN
Tricorn Black
SW 6258
Hazelnut
Natural Alder

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Parts List
1614a_1620a_1626a_1632a_Finished — Page 4 — 07/17
Part
Description
Quantity
1614a
1620a
1626a
1632a
L
#8 Washer (inserted)
7
7
8
11
M
Pad Strip
2
2
2
3
N
Lock Plate
2
2
2
2
O
Rafix Bolt (attached)
4
4
4
8
P
Rafix Cam (attached)
4
4
4
8
Q
Shelf Bracket (installed)
8
8
8
16
TB
Bookcase Tipping Restraint
1 set
1 set
1 set
1 set
1632 shown in the illustrations.

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Assembly Instructions
1614a_1620a_1626a_1632a_Finished — Page 5 — 07/17
Tools Required: Phillips Screwdriver, Pencil, Rubber mallet or Padded hammer.
1. To move the adjustable shelves:
Determine where you want to place the Adjustable Shelves (C). Remove the #6 x 1/2" Undercut
Screws (G) from the underside of the shelf and take out the shelf and Shelf Brackets (Q). Insert
the Shelf Brackets (Q) flat side down into the four different holes and install the shelf. You may
secure them by inserting #6 x 1/2" Undercut Screws (G). See Figures 1 and 1a.
2. NOTE: READ THE RAFIX ATTACHMENT SYSTEM INSTRUCTIONS NOW (See Page 10)
BEFORE YOU BEGIN THE FOLLOWING STEP.
To move the Lower Shelf (D) or Lower Shelves (E and F), loosen the Rafix Cams (P) and
remove the Shelf/Shelves. Reposition the Rafix Bolts (O), replace the shelf and settle the Rafix
Cams over the Bolts. Tighten the Rafix Cams. See Figures 2, 2a and 2b.
Fig. 1
G
Q
Fig. 1a
C
C
C
C
Fig. 2
P
O
Fig. 2b
E
F
D
Fig. 2a
(1632)
(1614)

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Assembly Instructions
1614a_1620a_1626a_1632a_Finished — Page 6 — 07/17
3. Place the Hutch face-up on a clean, protected surface. Peel the backing tape off one of the
Pads Strip (M) and place it on the bottom of the left side of the Case Assembly. Repeat for the
right side and for the 1632 on the Vertical Divider. See Figure 3.
Continued on Page 5
Fig. 3
M

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Assembly Instructions
1614a_1620a_1626a_1632a_Finished — Page 7 — 07/17
4. It is important you secure your Hutch to your Cabinet. Place the Hutch on top of the McKenzie
Alder Cabinet and line it up with the back and sides. Find the Lock Plates (N) attached at each
side of the Hutch near the bottom edge and remove the innermost screw (I) from each. Rotate
the end of the Plate downward until the hole for the screw is centered on the back edge of the
top of the Cabinet. Insert the screws into the Cabinet to secure the Hutch as shown in Figures 4
and 4a. For additional stability, insert a #8 x 1-1/4" Pan Head Screw (J) through the pocket hole
located behind the face molding on each side panel on the Hutch. Note this will create two holes
in the top of the Cabinet. See Figures 4b and 4c.
5. Your Base unit includes a Tipping Restraint Kit to secure the completed item to the wall to
protect from possible tip over hazards. If you are attaching this Hutch to an older Cabinet and
no longer have the Tipping restraint kit, use the Kit included with this Hutch to secure the
item. Attach the end of the Strap to the Bottom Shelf of your Cabinet unit near the back edge at
the center of the item, and follow the instructions in the Tipping Restraint Kit.
Fig. 4
I
Fig. 4a
N
Fig. 4b
Fig. 4c
Back on the Hutch removed for illustration purposes.
J

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Assembly Instructions
1614a_1620a_1626a_1632a_Finished — Page 8 — 07/17
Bookcase Tipping Restraint Instructions
Before you begin this assembly, identify each part and make sure the quantities received match what is on this
list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following
list for its name and letter code.
Part
Description
Quantity
A
Cam Buckle and Short Strap (installed)
1
B
Plastic Bracket (installed)
1
C
1" x 1000mm Long Strap (installed)
1
D
#8 x 3" Pan Head Screw
2
F
Washer (installed)
1
G
#8 x 5/8" Pan Head Screw
2
(1 inserted)
H
#8 x 1-1/4" Pan Head Screw
1
I
“L” Angle Bracket
1
If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.
Continued on Page 7

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Assembly Instructions
1614a_1620a_1626a_1632a_Finished — Page 9 — 07/17
6. Decide where you want to place the bookcase in your room. Mark the baseboard with a pencil
mark directly behind the location where the tipping restraint is attached to your item. Move the
item away from the wall far enough to allow you to access the spot where the baseboard meets
the floor. Position the straps and Plastic Bracket (B) as shown in Figures 6 and 6a with the
angled corners of the Plastic Bracket (B) firmly placed against the seam of the baseboard and
floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the Plastic Bracket
(B) into the seam below the baseboard where it meets the floor. See Figures 6 and 6a.
Fig. 6
D
x 2
Fig. 6a
Wall
Floor
D
Floor
Baseboard

1614a; 1620a; 1626a & 1632a McKenzie Alder Hutch
Assembly Instructions
1614a_1620a_1626a_1632a_Finished — Page 10 — 07/17
7. Move the item back into position against the wall and reach underneath the bookcase to grasp
the loop in the free end of the strap. Pull the free end of the strap until portion between the Cam
Buckle (A) and the bottom of the item is tight. See Figures 7 and 7a. If you need to move the
bookcase reach beneath and locate the buckle which connects the two sections of the strap and
depress the release lever, then pull on the section of strap that is between the buckle and the
bottom of the furniture until there is enough slack to allow you to pull the item away from the
wall.
Fig. 7a
Fig. 7
C
Wall
Floor