Englefield VALENCIA User manual

1378364-A02-B 25/01/2018
INSTALLATION
INSTRUCTIONS
FURNITURE
Englefield
VALENCIATM LED Mirrors
NOTES:
1. Fitting instructions are intended to facilitate installation. They are not
subject to contract.
2. Since the type of wall determines the fittings necessary for each unit,
bolts and screws have not been supplied for hanging the mirror but left
to the responsibility of the installer.
WARNINGS:
This installation must comply with the most recent AS/NZS 3000
electrical standards.
The light source of this luminaire is not replaceable; when the light
source reaches its end of life the whole luminaire shall be replaced.

BEFORE YOU BEGIN
ROUGH-IN
Page 1
INSTALLATION INSTRUCTIONSVALENCIA
TM
LED Mirrors
Please read these instructions carefully to familiarise yourself with the required tools, materials, and
installation sequences. Follow the sections that pertain to your particular installation. This will help you
avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.
Prior to installation, inspect your Valencia LED mirror to ensure that no damage has occurred in transit.
If damage has occurred, or a visible defect exists, do not proceed with installation, and advise your supplier
immediately.
Please leave these instructions for the consumer. They contain important information.
ENGLEFIELD
Instructions, drawings, and diagrams contained in this manual present information available at the time of printing.
changes without further notice.
900mm Model
750mm Model
The two top fasteners must be fixed to a nog in
the wall.
TOOLS & CONSTRUCTION REQUIREMENTS
650
30
900
750
30
650
TOOLS

INSTALLATION
Page 2
INSTALLATION INSTRUCTIONS
ENGLEFIELD
VALENCIA
TM
LED Mirrors
10cm
75cm / 90cm
2.7cm
2.7cm
65cm
1. Select an appropriate location to install the mirror where it can be fastened to a nog, and where
wiring can be connected without any slack in the wiring.
2. Use a spirit level and refer to the dimensions below to mark the location of the fixing holes with a
sharpened pencil.
3 Pre-drill holes at the marked locations. When drilling holes make sure to do so as accurately as
possible. Install appropriate fasteners.
4. Using the two small screws provided, install the bracket onto the bottom of the mirror.
5. Carefully hang the mirror on the cleats and use a spirit level to check that the mirror is level, make
adjustments as necessary to the position (This may require two people).
6. Mark the location of the bottom bracket on the wall with a pencil. Lift and remove the mirror from the
wall to reveal the pencil mark location of the bracket.
7. Un-install the bracket from the mirror by removing the two small screws previously installed during step 4.
456
Mirror
Wall
7
8. Using the larger screw provide, mount the bracket to the wall at the marked pencil location, do not
over-tighten. If there is no stud present, use the supplied wall anchor.

CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER AU
Free Ph: 1 800 228 476
www.englefield.com
For warranty information, please visit our website
Englefield
INSTALLATION INSTRUCTIONSVALENCIA
TM
LED Mirrors
PRODUCT FEATURES
It is recommended that all moisture be removed with a soft cloth after each use.
To clean the mirror surface use a soft cloth with warm water and methylated spirits.
Apply the cleaning solution to the cloth. Make sure all edges are thoroughly dry after cleaning.
Cleaners should not be applied directly to the mirror surface as it could come into contact with the back of
the mirror causing damage.
Do not use abrasive cleaners that could scratch the mirror. Acidic, alkali or extra strength ammonia cleaners
should be avoided as these can damage the copper coating and destroy the mirror.
NOTICE
CLEANING AND MAINTENANCE INSTRUCTIONS
There is a sensor switch located at the bottom right-hand corner of the
mirror. To turn the LED light on and off, simply place your hand under the
sensor as shown in the image.
The built in demister functions when the LED is switched on. To prevent
the mirror from fogging up, turn the LED light on before bathing or
showering.
SENSOR SWITCH:
DEMISTER:
9. Electrical hard wiring should be connected by a certified electrician, ensuring compliance with
AS/NZS 3000 electrical standards are observed.
10. Lift the mirror and carefully lower it onto the cleats. Using the two small screws provided, align
the lower bracket and fasten it to the mirror.
Installation Complete.