Enventor Y011R User manual

LASER LEVEL
ModelY011R Y011G
OWNER'S MANUAL & SAFETY
INSTRUCTIONS
Read this material before using this product . Failure to do so can
result in serious injury. Save this manual
OWNER'S MANUAL
SAFETY
INSTRUCTIONS
Manufacturer
Shenzhen Shangu Trading Co., Ltd.
Room 407, No. 51 Pingxin North Road, Shangmugu Community,
Pinghu Street, Longgang District, Shenzhen
Made in China
[email protected]

INSTRUCTIONS MANUAL
English
Deutsch
Français
Italiano
Español
Polski
1-8
9-16
17-24
25-32
33-40
41-48
Enventor LASER LEVEL
Model Y011R Y011G

1.Safety Instructions
1 2
Enventor LASER LEVEL INSTRUCTIONS MANUAL
WARNING
WARNING
ATTENTION
NOTE
User Guide, Maintenance and Care：
EN
Thank you for purchasing Enventor Y011G/Y011R Laser Level. Before using the product,
please read this manual thoroughly to ensure proper use.
Please read thoroughly and comply with the Safety Instructions and User Manual before
using this product. Failure to read and follow may void the warranty.
Read all instructions prior to operating this laser tool. Do not remove any labels from
tool.
• While the product is in operation, be careful not to expose your eyes to the emitting
laser beam . Exposure to a laser beam for an extended time may be hazardous to your
eyes.
• Do not attempt to view the laser beam through optical tools such as telescopes as
serious eye injury may result.
• Do not disassemble or modify the laser in any way. Modifying the tool may result in
hazardous Laser Radiation Exposure.
• Do not operate the laser around children or allow children to operate the laser. Serious
eye injury may result.
• An exposure to the beam of a Class 2 laser is considered safe for a maximum of 2
seconds. Eyelid reflexes will normally provide adequate protection.
• The following label/print samples are placed on the product to inform of the laser class
for your convenience and safety.
• When not in use please power OFF the tool and place the pendulum lock in its locked
position.
• The laser tool is sealed and calibrated at the plant to the accuracy specified.
• It’s recommended to carry out an accuracy check before its first use and periodic
checks during future use, especially for precise layouts.
• Do not store the laser tool in direct sunlight or expose it to high temperatures.
• Exterior plastic parts may be cleaned with a damp cloth, NEVER use solvents. Use a soft,
dry cloth to remove moisture from the tool before storage.
• Do not dispose of this product with household waste.
• Please recycle in line with local provisions for the collection and disposal of electrical
and electronic waste under the WEEE Directive.
CLASS II LASER PRODUCT
COMPLIES WITH CFR 1040.10 AND 1040.11
Max. Power Output: <1mW
Wavelength: 505nm-660nm
LASER RADIATION:
DO NOT STARE INTO BEAM.
DO NOT DIRECT EYE EXPOSURE.
AVOID VIEW WITH OPTICAL INSTRUMENTS.

3 4
Enventor LASER LEVEL INSTRUCTIONS MANUAL
EN
2.Charging and Battery Safety
Please read thoroughly and comply with the battery safety instructions and precautions
before charging.
Failure to read and follow may result in personal injury, fire, and property damages if the
battery is charged and/or used improperly.
Charging Precautions:
Battery Safety:
3.Specifications
• Suitable power adapter: Universal adapter with output of 5V=1A or 5V=2A
• The first charging time is recommended to be more than 4 hours. Each charge time is
not less than 2.5 hours, but not more than 12 hours.
• If the laser tool is not used for an extended time, please charge once every 6 months,
each charging time is not less than 4 hours.
• The best charging temperature: 0℃to 20℃(32℉to 68℉)
• DO NOT SHORT CIRCUIT. Short circuits may cause fire, and injury!
• Do not charge unattended.
• Do not disassemble, or modify the battery.
• Keep away from children, and pets.
• Immediately discontinue use of the battery if the battery abnormal/ deformed (emits
an unusual smell, feels hot, changes color or shape, or appears abnormal in any other
way). Please contact the manufacturer to replace it.
• Never charge or store the batteries inside your car. Extreme temperatures (low or high)
might ignite the battery, and cause a fire.
• Do not place the battery in high-pressure containers, microwave ovens, or on induction
cookware.
• Do not carry, or store the batteries together with hairpins, necklaces, or other metal
objects.
• On (battery electrolytes) exposure to skin, flush with water immediately. If eye
exposure occurs, flush with water for 15 minutes, and seek emergency care immediately.
Model:
Laser Class:
Laser Wavelength:
Leveling Accuracy:
Y011G-Green Beams
Class 2 (IEC/EN60825-1/2014), <1mW
505-530nm
±3mm/10m(±1/9 in. at 33 ft)
Leveling / Compensation Range:
Self-leveling Time:
Reference Working Distance
( 60-100 LUX):
Reference Working Distance
(with Laser Detector):
3°±1°
≤4 seconds
25m / 82ft
Up to 50m / 164ft
Power Source:
Reference Operating Time:
Charging Time:
Power Adapter (Optional):
Li-ion Battery 3.7V 2200mAh
About 7 hrs
625-645nm
20m / 65ft
Up to 35m / 114ft
About 20 hrs
About 2.5 hours
5V=1A or 5V=2A
Mount Size:
IP Rating:
1/4''-20
IP54
Work Temperature:
Storage Temperature Range:
-10℃~ +50℃
-20℃~ +70℃
Y011R-Red Beams

4.Product Overview
5.Operation & LED Indicator
Turn ON the laser tool:
5 6
Enventor LASER LEVEL INSTRUCTIONS MANUAL
EN
1.Operation Button
2.LED Indicator
3.Laser Window
4.Pendulum / Transit Lock
5.1/4"-20 threaded mount
6.Type - C Charging Port
Method 1 - Turn ON the self-leveling mode:
• Slide the pendulum to the Unlocked Position to turn ON the laser tool, the self-leveling
mode is activated by default.
• The laser beams blink fast when the tool is out of self-leveling range (3° ±1°).
Lines Switching:
After power on, all laser beams will be on by default.
•Short press operation button(1) to switch horizontal and vertical laser line.
Turn OFF the laser tool:
• Step 1: Slide the pendulum/transit switch to the Locked Position.
• Step 2: press operation buttons(1) and hold for ≥2 seconds to turn the laser tool OFF.
The laser level can only be turned off when the pendulum/transit in its Locked Position.
Method 2 - Turn ON the manual / Tilt mode:
• When the pendulum in Locked Position, press operation button(1) and hold for ≥2
seconds to turn ON the laser tool, the manual mode is activated by default.
• The laser beam will blink about every 5 seconds to notify the user it is not self-leveling
now.
• Under manual mode, users can position the laser tool at various angles.
Note: Please notice the laser beam projected in manual mode cannot be used as a
horizontal or vertical reference in nature.
NOTE
• Appearance and specifications may differ due to product improvement.
• Working distance varies depending on the operating environment.
• When use with receiver for a larger working range, it’s necessary to turn on the pulse
mode.
NOTE
1
2
3
4
6
5

6.After-Sales Service Hot-mail
LED Indicator :
7 8
Enventor LASER LEVEL INSTRUCTIONS MANUAL
EN
Return Back to Normal Mode:
• short press the operation button twice in a row to return back to Normal Mode.
• The laser beams will be recovered, and the LED indicator (2) will light up in green.
• After Power ON, the LED indicator will light up in Green.
• When the battery is low, the power indicator will flash in red.
• During charging, the power indicator will flash in green.
• When charging is complete, the power indicator will light up in green continuously.
•When switching to pulse mode, the LED indicator will light up in blue.
•When the battery voltage is low, switch to pulse mode, the LED indicator will flash in
red.
For questions about this or any other Products, please email us: aftersale_service@en
ventor.net.
Pulse Mode (Use with Laser Receiver):
• Under pulse mode, laser tool can work with a laser receiver for working in a brighter
environment or a larger working distance.
• It is necessary to turn on the pulse mode when use with the receiver.
Switch to Pulse Mode:
• Step 1: Turn ON the laser tool.
• Step 2: short press the operation button twice in a row to switch to Pulse Mode.
• The laser beamsaredimmer inpulse mode, andthe LED indicator(2) will light up in blue.
EU DECLARATION OF CONFORMITY
We hereby declare that the essential requirements set outin the EMC
directive 2014/30/EUand ROHS directive 2011/65/EU and FCC and IEC60825.
have been fully fulfilled on our product with indica tion as below:
Manufacturer: ZHONGSHAN SMART OPTOELECTRONICS TECHNOLOGY CO, LTD
Address: 1/F-3,Building A, No 16 Qianjin 3rd Road, Tanzhou Town, Zhongshan,
Guangdong, China
Object(s) of the declaration；
Product: :Self-leveling Cross Line Laser Level；
Model Number: Y011G,Y011R
Type: Electric
Applied Standard:
the EMC Directive 2014/30/EU
EN55032:2015
EN55035:2017
ROHS directive 2011/65/EU:
IEC62321-4:2013/AMD1:2017;IEC62321-5:2013;
IEC62321-6:2015;IEC62321-7-1:2015;
IEC62321-7-2:2017;IEC62321-8:2017
FCC
FCC Part 15 Subpart B
IEC
IEC 60825-1:2014
place and date of the declaration: Zhongshan, May 20, 2021
signature of the person: Eric Yu
Eric Yu