Enviro Kodiak 1200 FPI User manual

50-2910
WARRANTY REGISTRATION
enviro.com/warranty
OWNER`S MANUAL
Tested &
Listed By
Portland
Oregon USA
OMNI-Test Laboratories, Inc,
C
O-
T L
US
Report # 268-S-06b-2
Report # 268-S-05-2, 268-S-06c-2
Kodiak 1200 FPI & Kodiak 1700 FPI
W O O D S T O V E I N S E R T
INSTALLER: LEAVE THIS MANUAL WITH THE WOOD STOVE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
Version Française: www.enviro.com/fr.html
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS
WOOD BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN PROPERTY DAMAGE, BODILY HARM, OR EVEN DEATH.
CONTACT YOUR BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND
INSTALLATION INSPECTION REQUIREMENTS IN YOU AREA.
THIS HEATER MEETS THE 2015 U. S. ENVIRONMENTAL PROTECTION AGENCY’S CRIB-
WOOD EMISSION LIMITS FOR WOOD HEATERS SOLD AFTER MAY 15, 2015. UNDER
SPECIFIC CONDITIONS THIS HEATER HAS BEEN SHOWN TO DELIVER HEAT AT RATES
RANGING FROM 11,479 TO 34,196 BTU PER HOUR FOR THE 1200 AND FROM 9,425 TO
31,780 BTU PER HOUR FOR THE 1700. THESE STOVES HAVE BEEN CERTIFICATION TESTED
TO STANDARDS UL-1482-11 AND ULC-S627-00. CERTIFICATION TESTING COMPLETED BY
OMNI-TEST LABORATORIES.

Table of Contents
2
Safety Precautions..........................................................................................3
Emissions and Efciency..................................................................................4
Operating Instructions.....................................................................................5
Building Your Fire.................................................................................6
How It Works......................................................................................10
Specications................................................................................................11
Air Control.........................................................................................11
General Specications........................................................................11
Clearances To Combustibles - 1200 KI Insert.........................................12
Clearances To Combustibles - 1700 KI Insert.........................................13
Dimensions - 1200 KI Insert.................................................................14
Dimensions - 1700 KI Insert.................................................................15
Installation...................................................................................................16
Removal From Pallet..........................................................................16
Modications For Installation with 19” (483mm) High Lintel...........16
Masonry Fireplace Installation.............................................................17
Installation Using A Block-Off Plate For USA Only..................................20
Model 1200 KI Brick Placement & Tube Locations.................................22
Model 1700 KI Brick Placement & Tube Locations..................................23
C-Cast Ceramic Bafe Installation........................................................24
Fan Wiring Diagrams..........................................................................25
Fan Removal......................................................................................25
Removal of Top..................................................................................26
Installation Of The Surround Panel......................................................26
Rating Label.................................................................................................27
Parts List......................................................................................................28
Parts Diagram...............................................................................................29
Notes..................................................................................................30
Warranty......................................................................................................31
Installation Data Sheet...................................................... ............................32

3
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE OF YOUR NEW
WOOD STOVE. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH. BE AWARE THAT LOCAL CODES AND REGULATIONS MAY
OVERRIDE SOME ITEMS IN THIS MANUAL. PLEASE CHECK WITH YOUR LOCAL BUILDING
OR FIRE AUTHORITY.
• This appliance becomes extremely hot when in use and can cause burns if contacted.
• Young children should be carefully supervised when they are in the same room as the appliance.
• Make sure you have incorporated proper safety measures to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is out, the rebox and glass will remain hot for an extended period of time.
• If this appliance is not properly installed, operated, and maintained a serious house re could result.
• Installation of appliance must be completed by a certied installer.
• Wear protective gloves and safety glasses during installation, sheet metal edges may be sharp.
• Do not operate without fully assembling all components.
• Do not use any makeshift materials during installation, maintenance, or replacement.
• Any changes or alterations to this appliance are dangerous and prohibited.
• This appliance has been designed to burn dried and seasoned hardwoods.
• Do not use chemical uids to start or re-fresh the re.
• Do not burn coal, charcoal, or treated wood as there is danger of carbon monoxide being produced.
• Do not burn garbage or ammable uids such as gasoline, grease, naphtha or engine oil.
• Never let the stove become hot enough to get any part glowing red.
• Do not operate with door open, door must be tightly closed.
• Do not strike or slam shut the ceramic glass door, if the door glass is broken or a gasket is missing or damaged
appliance must be repair by a qualied service technician before resuming use.
• At least 12 square inches (77.4 cm2) of fresh outside air should be admitted into the room or directly to the
stove through a 4 inch (10.16 cm) diameter pipe.
• Do not burn wet unseasoned wood, this can causes excessive creosote accumulation. When this is ignited it
can cause a chimney re that may result in a serious house re.
• Do not use grates, andirons or any other methods to support or raise the re up off the re bricks.
• Do not place clothing, furniture, draperies, or any other ammable materials on or near the appliance.
• Objects placed in front of the appliance must be kept at least of 48” away from the front face of the appliance.
• Do not connect appliance to a chimney ue pipe servicing another solid fuel burning appliance.
• Do not install in a mobile home this appliance is not Certied for that application.
• Do not attach to any kind of heat distribution ducting system.
• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.
• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to
smoke spillage in your home.
• A chimney connector shall not pass through an attic, roof space, oor, ceiling, closet or similar concealed space.
• Do not store wood within appliance installation clearances or within the space required for refueling and ash
removal.
• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away
from the home or structure until completely cool.
• Ensure proper clearances to combustibles are maintained when building a mantel or shelves above the appliance.
IMPORTANT: The following must be done to ensure
proper operation. Failure to do so will cause extreme
overheating and possible personal injury or property
damage. If an outside air supply has not been added
to this appliance, please ensure that the 4” inch fresh
air inlet on the back of the pedestal is removed. Also
ensure the ash plug is installed in the rebox.
Safety Precautions

4
Emissions and Efficiencies
Emissions and EfficiEncy - 1200-K insErt:
KodiaK 1700
Efciency: 75%
Emissions and EfficiEncy - 1700-K insErt:
KodiaK 1200
Efciency: 71.6%
WARNING: This wood heater needs periodic inspection and repair for proper operation. It is
against federal regulations to operate this wood heater in a manner inconsistent with operating
instructions in this manual.
WARNING: This wood heater has a manufacturer set minimum low burn rate that must not
be altered. It is against federal regulations to alter this setting or otherwise operate this wood
heater in a manner inconsistent with operating instructions in this manual.
Rates: This manual describes the installation and operation of the Enviro Kodiak 1200 wood
heater. This heater meets the 2015 U.S. Environmental Protection Agency’s wood emission
limits for wood emission limits sold after May 15, 2015. Under specic test conditions this
heater has been shown to deliver heat at rates ranging from 9,400-32,000 Btu/hr.
Rates: This manual describes the installation and operation of the Enviro Kodiak 1200 wood
heater. This heater meets the 2015 U.S. Environmental Protection Agency’s wood emission
limits for wood emission limits sold after May 15, 2015. Under specic test conditions this
heater has been shown to deliver heat at rates ranging from 11,500-34,000 Btu/hr.
Stress Lines:
Stress lines located within the rebox at the secondary air channels may result from the repeated
expansion and contraction of metal during regular use. These lines, when narrower than the thickness
of a coin, do not compromise the safety or efciency of the unit and as such do not necessitate repair or
replacement.
Similarly, stress lines that may appear on the rebox front due to regular use also do not compromise
safety or efciency of the unit, with the possible exception of the door gasket. In the event that these
extend beyond the door gasket, they may have a minor effect on the integrity of the seal and will then be
covered by the warranty policy for repair.

Operating Instructions
FIRST START
When rst installed, the chimney, rebricks and steel are cold and it usually takes several hours on a
high burn for them to become hot and dry enough for the stove operate at maximum efciency. We
recommend during the rst burn that a door or window is opened to vent the smoke and fumes created
while the paint cures. The paint should be completely cured after the rst few burns.
DISPOSAL OF ASHES:
If you let the ashes accumulate two or three inches on the oor of the Firebox they tend to burn
themselves up. Fireplace inserts do not have an ash drawer so eventually the ashes will need to be
scooped into a metal container with a tightly tting lid. Place the closed container on a non-combustible
surface, well away from combustible materials.
If the ashes are to be buried in soil or otherwise locally dispersed, keep them in a closed container until
all cinders have completely cooled. Small amounts of wood ash can be used in the garden or compost.
FAN OPERATION:
All insert models have been approved for operation with the fans supplied by the manufacturer. During a
medium or high burn, using a fan will increase the heat transfer and circulation. Route the power supply
cord along the oor behind or away from the stove where it will remain cool.
1. Plug the fan assembly into a standard three (3) prong grounded electrical receptacle.
2. There is a three position switch located on the fan pod. The auto/off/manual rocker switch allows the
fan to be turned on manually, or automatically. When this switch is up it is set to the manual position.
The center position is off. When the switch is pushed down it is set to the automatic position.
3. In the manual position the Rotary Rheostat knob is used to turn the fan on and off as well as adjust
the ow.
4. In the automatic position the fan will automatically turn on once the fan temperature sensor reaches
the operating temperature. When the unit cools down, the fan temperature sensor will shut the fan
off. You should set the desired ow while in the manual position.
REPLACING THE GLASS:
Never strike or slam the door, hit the glass or let burning wood rest against it. If the glass cracks when
the re is burning, do not open the door until the re is out. Do not operate the stove again until the
glass has been replaced. If the glass is damaged in any way, a factory replacement is required (see “Parts
List”). To replace the glass, remove the steel retainer and all loose glass. Replace only with Neoceram
5 mm glass 16 ⅝” (422 mm) x 10 ⅝” (270 mm) and wrap the edges with ⅛” (3.2 mm) x ½” (13 mm)
self-adhesive berglass gasket, see parts list for part number.
Wear protective gloves when handling damaged glass door assembly to prevent personal injury. When
the glass door assembly is being transported, it must be wrapped in newsprint and tape and/or a strong
plastic bag. Replacement glass must be purchased from an ENVIRO dealer. No substitute
materials are allowed.
FIRE EXTINGUISHER AND SMOKE DETECTION:
All homes with a wood burning stove should have at least one re extinguisher in a central location
known to all in the household. Smoke detectors and carbon monoxide detectors should be installed
and maintained in the room containing the stove. If it sounds the alarm, correct the cause but do not
deactivate. You may choose to relocate the smoke detection devise within the room; DO NOT REMOVE
THE SMOKE OR CARBON MONOXIDE DETECTORS FROM THE ROOM.
5

CREOSOTE - ITS FORMATION AND REMOVAL:
When wood is burned slowly, it may produce tar and other vapors that, combined with moisture, form
creosote. These creosote vapors condense in the relatively cool chimney ue of a slow burning re and, if
ignited, make an extremely hot re. Therefore, the smoke pipe and chimney should be inspected at least
once every two months during the burning season. If creosote has accumulated it should be removed to
reduce the risk of a chimney re.
MAINTENANCE:
At the end of each heating season your chimney and the smoke pipe will need to be professionally
cleaned. If soot has accumulated above the top bafe they will need to be removed and cleaned. If
Bafes are damaged they need to be replaced. If the secondary air tubes are badly eroded or warped,
replace them. Replace worn door gaskets and broken bricks as needed.
FAILURE TO INSPECT AND CLEAN YOUR CHIMNEY SYSTEM REGULARLY CAN RESULT IN A
CHIMNEY FIRE, WHICH COULD DAMAGE THE CHIMNEY OR CAUSE A HOUSE FIRE.
CHIMNEY OR RUN AWAY FIRE:
1. Alert and evacuate all people inside the home. You should have an evacuation plan in place for such
an event as well as a safe place to meet.
2. Fully close the Air Damper to limit oxygen to the re.
3. Call local re department (or dial 911). Have a re extinguisher and a garden hose ready, your local
re authority will provide you with instructions to handle the situation.
4. Once the re is out examine the ue pipes, chimney, attic, and roof of the house, to see if any part
has become damaged by the re.
4. Do not operate the stove again until the chimney and its lining have been cleaned and you are certain
they have not been damaged. We strongly recommend inspection by a WETT (Wood Energy Technical
Training) certied installer in Canada or a HEARTH (Hearth Education Foundation) certied installer in
the U.S.A. before starting another re.
BUILDING YOUR FIRE:
Proper operation of your stove will help to ensure safe, efcient heating. Please take a few moments to
review these simple operating procedures.
IMPORTANT: Please be aware when loading your stove that the air tubes in the rear are lower than
the front.
1. Fuel Selection:
This stove is designed to burn natural wood only. Higher efciencies and lower emissions generally
result when burning air dried seasoned hardwoods, as compared to softwoods or to green freshly cut
hardwoods. Wood should be properly air dried (seasoned) for at least six months, a year is preferred.
Wet or freshly cut wood will cause the re to smolder creating creosote. Wet wood also creates very little
heat and res tend to go out.
DO NOT BURN: treated wood, salt water wood, coal, charcoal, garbage, plastic, solvents, or colored
papers. These material contain chlorides which will rapidly corrode and warp metal surfaces which voids
warranty.
Operating Instructions
6

Operating Instructions
2. Building/Maintaining a Fire:
a) Open the primary air slide by pulling it all the way to the right.
b) Place a base of crumpled uncolored paper in the bottom of the stove. Lay pieces of kindling on top of
the newspaper and light it.
CAUTION: “Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid,
or similar liquids to start or “freshen up” a re in this heater. Keep all such liquids well
away from heater while it is in use.
c) As the kindling begins to burn, add several slightly larger pieces of wood until the re is burning well.
Once a coal bed had been established regular size logs may be added.
NOTE: Until the re is burning well, leave the air control fully open.
d) Regulate the heat output and duration of burn by adjusting the air controls to allow a larger re and
vice versa. A short period of experimentation with the control settings will allow you to regulate the
heat output to keep your home comfortable.
Do not use a grate or elevate the re. Build re on top the bricks inside the rebox.
3. Refueling the Stove:
Use a long pair of gloves (barbecue gloves) when feeding the re because these stoves burn at the front.
They are clean and efcient but they are also very hot and gloves are useful. Keep a small steel shovel
and whisk nearby for moving a log or lifting a fallen ember and for keeping the hearth clean.
a) Before attempting to add fuel to the stove, OPEN the damper control fully by pulling it all the way out.
This allows the chimney to carry away the additional smoke, which occurs when the door is open.
b) DO NOT OVERLOAD THE STOVE. Normally, three or four logs will provide heat for several hours.
Never operate this stove where portions glow red hot. Using more than ve logs at a time can cause
overring. Keep logs a few inches from the lowest point of the top of the rebox. If any logs are touching
the tubes in the top of the rebox, you can damage the air tubes. Overloading the stove can cause
damage to the rebox and air tubes and will void the warranty.
c) DO NOT OVERFIRE. If the heater or chimney connector glows, you are overring. If the stove top
temperatures exceed 550°F, you are overring. Overring your stove will void the warranty.
d) WHAT IS OVERFIRING? Overring is when the stove is generating too much heat in the rebox,
causing parts within your stove to glow red and warp. To spot overring, place a thermometer on the
stove top. If the stove top temperatures exceed 550°F, you are overring. Another way to spot overring
is if the heater or chimney connector glows.
e) CAUTION: DO NOT PLACE FUEL OR COMBUSTIBLE MATERIAL WITHIN SPACE HEATER INSTALLATION
CLEARANCES OR WITHIN THE SPACE REQUIRED FOR CHARGING AND ASH REMOVAL. LOGS SHOULD BE
KEPT IN A BIN OR CONTAINER TO REDUCE THE RISK OF LOGS ROLLING INTO THE UNIT’S CLEARANCES.
f) HOW TO AVOID OVERFIRING: To avoid overring, do not overll your rebox. Usually a maximum
of four logs at a time is sufcient enough to avoid overring. Keeping stove top temperatures under
550°F will also prevent overring.
g) KEEP THE ASH LIP CLEAR OF EMBERS AND ASH. If the door is closed with debris in the way,
the door gasket seal could be compromised.
h) CAUTION: DO NOT PLACE FUEL WITHIN SPACE HEATER INSTALLATION CLEARANCES OR WITHIN
THE SPACE REQUIRED FOR ASH REMOVAL.
4. For Maximum Efciency:
When the stove is hot, load it fully to the top of the door opening and burn at medium low settings. When
the fuel is mostly consumed, leaving a bed of red coals, repeat the process. Maximum heat for minimum
fuel occurs when the stove top temperature is between 250°F (120°C) and 550°F (290°C).
7

Operating Instructions
Helpful Hints Worth Repeating
1. Helpful advice on the correct way to start your re.
a) You will need small pieces of dry wood, called kindling, and paper. Use only newspaper or paper
that has not been coated or had other materials glued or applied to it. Never use coated (typically
advertising yers) or coloured paper.
b) Always fully open the air control damper and slowly open wood stove door to prevent suction and
drawing smoke into the room.
c) Crumple several pieces of paper and place them in the center of the rebox directly onto the rebricks.
Never use a grate or andirons to elevate the re.
d) Place small pieces of dry wood (kindling) over the paper in a criss cross manner. This allows for good
air circulation, which is critical for good combustion.
e) Light the crumpled paper in 2 or 3 locations.
Note: It is important to heat the air in the stovepipe for draft to start.
f) Fully open the air controls of the wood stove and close the door until it is slightly open, allowing for
much needed combustion air to be introduced into the rebox. Never leave the door fully open, as
sparks from the kindling may y out of the stove, causing damage or injury. As the re begins to burn
the kindling, some additional kindling may be needed to sustain the re. DO NOT add more paper after
the re has started.
g) Once the kindling has started to burn, add some smaller pieces of seasoned rewood. Note: Adding
large pieces at the early stages will only serve to smother the re. Continue adding small pieces of
seasoned dry rewood, keeping the door slightly open until each piece starts to ignite. Remember to
always open the door slowly when placing wood into the re.
h) Once the wood has started to ignite and the smoke has reduced, close the wood stove door fully. The
reduction of smoke is a good indication that the draft in the chimney has started and good combustion
is now possible. Larger pieces of seasoned, dry rewood can now be added when there is sufcient
space in the rebox. Adjust the air control setting to desired setting.
Note: The lower the air control setting, the longer the burn time of your rewood.
2. What type of wood is best to use as rewood?
Both hardwood and softwood burn well in this stove. Both woods contain about 8,000 BTU/lb (18,570
KJ/Kg), but hardwood is generally more dense, will weigh more per cord, and burns a little slower and
longer. Cutting rewood so that it will t horizontally, front to back, makes it easier loading and less likely
for the fuel to roll on to the glass. Except for a cold start, there is no need to crisis-cross the logs. Ideal
length for the logs used in the 1200 would be about 16“ (381 mm) but it can burn pieces up to 18” long.
Ideal length for the logs used in the 1700 would be about 18“ (381 mm) but it can burn pieces up to 20”
long logs. Burn only seasoned wood, It produces more heat and less soot or creosote. Freshly cut wood
has about 50% moisture. A 10 pound (4.5 Kg) log contains 5 pounds (2.3 Kg) of water. Burn beach wood
only if its salt content has been washed away in a season of rain and then the dried again.
3. What does dry, seasoned wood mean?
Wood that has been dried for a period of one year in a well-ventilated and sheltered area would be
considered dry, seasoned wood. Wood from slow-growing trees is generally considered better than wood
from fast-growing trees. To season rewood, split and stack it so that air can get to all parts of the wood.
4. Will following the above-listed steps for starting a re mean perfect results every time?
The quick answer is ‘most of the time’. There are many variables that may affect your success when
starting a re. Most of those variables and how to deal with them will be learned through experience.
Your ability to start a good re will signicantly increase with time and patience. Some of the reasons for
poor stove performance will be covered in the next section of these instructions.
8

Operating Instructions
5. Why won’t my re light?
Damp or wet wood and a poor draft are the main reasons for poor results in starting a re. Always use
dry, seasoned wood for your re. Even wood dried for two years will be difcult to ignite if it has become
wet from rain.
6. Is it normal for soot to cover the glass at the beginning of a re?
Your stove has been built with an air-wash system that will help keep the glass clear when the rebox
has reached a good operating temperature and has a good draft. Normally a hot stove will keep the glass
clean. If you must clean the glass, use a soft non abrasive cloth and clean with water when unit is cold.
Cold rebox temperature and poor draft cause sooting of the glass. Once the rebox temperature and
the draft increase, the soot should burn off.
7. What is draft?
Draft is the ability of the chimney to exhaust or draw smoke produced during the normal combustion
process. Too much draft may cause excessive temperatures in the appliance and may damage the
appliance. Inadequate draft may cause back pufng or “plugging” of the chimney. There is a certain
amount of draft that is required to allow for your stove to function at its’ highest efciency. A water
column reading of 0.1” or more is recommended.
8. What can cause a poor draft?
The most common factors for poor draft are:
a) Lack of supply air b) Environmental conditions
c) Cold chimney temperature
d) Poor chimney installation and maintenance
e) Atmospheric pressure
a) Air supply – Inside the home, normal household appliances such as clothes dryers and forced-air
furnaces compete for air, resulting in air starvation to the wood stove. This creates a condition in the
house known as negative pressure. When a house experiences negative pressure, the combustion
gases can be drawn from the chimney and into the house. This condition is commonly referred to as
down-drafting. Increased amounts of insulation, vinyl windows, extra caulking in various places and
door seals can all keep heat in but may also make a home too airtight. An easy way to stop negative
pressure in a home is to crack a window in the room containing the stove.
b) Environmental Conditions - High trees, low-lying house location such as in a valley, tall buildings or
structures surrounding your house and windy conditions can cause poor draft or down drafting.
c) Cold Chimney Temperature - Avoid cold chimney temperatures by burning a hot re for the rst fteen
to forty minutes, being careful not to over-re the stove. If any part of the chimney or parts of the
stove start to glow, you are over-ring the stove. If possible,
d) Chimney Installation and Maintenance - Avoid using too many elbows or long horizontal runs. If your
chimney is too short it can cause difcult start-up, dirty glass, reduced heat, and down drafting when
door is open. Too tall a chimney may prompt excessive draft, which can result in very short burn times
and excessive heat output. If in doubt, contact a chimney expert and/or chimney manufacturer for
help. To reduce the chance of draw issues and chimney res regularly clean the chimney, rain cap,
and spark arrestor.
Note: These instructions are intended as an aid and do not supercede any local, provincial or state
requirements. Check with ofcials or authorities having jurisdiction in your area.
9. How can I reduce the visible emissions?
If all of these steps are followed, there should be no visible emissions.
9

Operating Instructions
How itworKs:
Exhaust Smoke
1/2" Ceramic baffle;
reflects heat down
to burn the particles
in the smoke.
Secondary air tubes;
creates a second burn
on the particles in the
smoke for a more efficient
& cleaner burn.
Convection Heat
Radiant Heat
Primary air; window
air wash (cooler air to
keep the glass clean).
Pilot air through
Twin pilot
injection ports.
Slider plate; used
for air flow control. Intake air.
Seasoned Firewood
Exhaust Smoke
1/2" Ceramic baffle;
reflects heat down
to burn the particles
in the smoke.
Secondary air tubes;
creates a second burn
on the particles in the
smoke for a more efficient
& cleaner burn.
Convection Heat
Radiant Heat
Primary air; window
air wash (cooler air to
keep the glass clean).
Pilot air through
Twin pilot injection ports.
Slider plate; used
for air flow control. Intake air.
Seasoned Firewood
Figure 2: 1200 KI Air Flow Path.
Figure 3: 1700 KI Air Flow Path.
10

GEnEral spEcifications:
Table 1: 1200 KI & 1700 KI General Information.
Model 1200 Insert 1700 Insert
Width x Depth 27” x 22.5”
(686 mm x 572 mm)
27” x 27”
(686 mm x 686 mm)
Height of body 19” (483 mm) or 19.5” (495 mm)
Fire box size
(depth x width x height)
16.1” x 18.25” x 11.15”
(409 mm x 464 mm x 283 mm)
20.65” x 18.25” x 11.95”
(525 mm x 464 mm x 304 mm)
Capacity 1.85 feet3
(0.0526 meter3)2.5 feet3 (0.0708 meter3)
* Approximate heating area 2200 feet2
(205 meter2)
3000 feet2
(280 meter2)
**E.P.A. output rating 11,479 to 34,196 BTU/hour
(3,361 to 10,013 watt)
9,425 to 31,780 BTU/hour
(2,760 to 9,306 watt)
*Duration on low burn 6 -10 hours 8 - 12 hours
Weight with packaging 335 lb (151.95 Kg) 390 lb (176.90 Kg)
E.P.A. Emissions 3.3 grams/hour
(0.116 oz/hour)
4.48 grams/hour
(0.158 oz/hour)
Surround Panels
Standard (width x height) 46” x 28.25” (1166 mm x 711 mm)
Oversized (width x height) 47.5” x 33” (1207 mm x 838 mm)
Rating Label Location Side of Unit; Behind Right Shroud
Specifications
air control:
The amount of combustion air going to the air wash and pilot is controlled by the air control rod located
on the right side of the unit. To increase your air pull the rod out, and to decrease push the rod in. All
Enviro wood stoves have a secondary air that ows through the stainless tubes at the top of the rebox
just below the bafes.
Pull this control all the way out when rst starting the
stove. Once the re has been established you may
adjust this control to set the burn rate of the re. If
this damper is closed at rst start-up, the re will burn
very slowly and could soot the appliance.
When shutting down the stove, fully open the air
control. This allows the chimney temperatures to
remain as high as possible for as long as possible. Cold
chimney temperatures create creosote. Figure 4: Air Control Rod.
Pull out - Increase
Push in - Decrease
11

Specifications
clEarancEs tocombustiblEs - 1200 Ki insErt:
AMinimum clearance to an unshielded side wall 10” (254 mm)
BMinimum clearance to an unshielded 8” (203
mm) mantel 21” (533 mm)
CMinimum top facing (protruding ¾” [19 mm])
clearance 17½” (445 mm)
DMinimum side facing (protruding ¾” [19 mm])
clearance 1” (25 mm)
E† From front of door opening to edge of oor
protection
USA 16” (406 mm)
CND 18” (450 mm)
F† From side/back of unit to edge of oor
protection
USA 6” (152 mm)
CND 8” (200 mm)
† FLOOR PROTECTION:
If unit is raised 0” - 2” (0mm-51mm); 1” (25mm) non-combustible material with k value = 0.84 or equivalent.
If unit is raised 2” - 8” (51mm-203mm); ½” (13mm) non-combustible material with k value = 0.84 or equivalent.
If unit is raised greater than 8” (203 mm) or more; any non-combustible material can be used.
Table 3: Reduction in (B) Minimum Clearance from 1200 KI to 8” (203 mm) Mantel.
Type of protection Modied Clearance
A minimum of .013” (0.33mm) sheet metal spaced out 1” (25mm) by non-
combustible spacers. 10½” (267 mm)
Ceramic tiles, or equivalent non-combustible material on non-combustible
supports and spaced out 1” (25mm) by non-combustible spacers. 14” (357 mm)
Ceramic tiles, or equivalent non-combustible material on non-combustible
supports with a minimum of .013” (0.33mm) sheet metal spaced out 1”
(25mm) by non-combustible spacers.
10½” (267 mm)
NOTES:
(1) Mantel protection must have at least 3” (75mm) edge clearance on all sides, except as provided in Note 4.
(2) If an adhesive is used to support non-combustible material, it shall not lose adhesive qualities at temperatures
likely to be encountered and shall not contribute a signicant combustible load.
(3) Heat shield mounting hardware attached to combustible materials must be placed at the lateral extremities of
the shield.
(4) Minimum clearance to unprotected walls and ceilings must be maintained.
Table 4: 1200 KI Insert Minimum Fireplace Size.
Masonry Zero Clearance
Minimum Depth 13½” (343 mm) 14” (279 mm)
Minimum Width at back of replace 22⅜” (568 mm) 23” (584 mm)
Minimum Width at front of replace 27” (686 mm) 27¼” (692 mm)
Minimum Width at front of replace to include shroud 36” (915 mm) 36” (915 mm)
Minimum Height 19¼” (489 mm)**
or 19¾” (502 mm) 20” (508 mm)
** If the masonry lintel height is only 19¼” (489 mm) to 19¾” (502 mm) refer to instaLLation - Modifications for
instaLLation with 19¼” (489 MM) high LinteL - insert
B
A
D
C
Adjacent wall
F
E
Table 2: 1200 KI Insert Clearance to Combustibles.
12

Specifications
clEarancEs tocombustiblEs - 1700 Ki insErt:
AMinimum clearance to an unshielded side wall 10” (254 mm)
BMinimum clearance to an unshielded 8” (203
mm) mantel 24” (610 mm)
CMinimum top facing (protruding ¾” [19
mm]) clearance 19½” (495 mm)
DMinimum side facing (protruding ¾” [19
mm]) clearance 1” (25 mm)
E† From front of door opening to edge of oor
protection
USA 16” (406 mm)
CND 18” (450 mm)
F† From side/back of unit to edge of oor
protection
USA 6” (152 mm)
CND 8” (200 mm)
† FLOOR PROTECTION:
If unit is raised 0” - 2” (0mm-51mm); 1” (25mm) non-combustible material with k value = 0.84 or equivalent.
If unit is raised 2” - 8” (51mm-203mm); ½” (13mm) non-combustible material with k value = 0.84 or equivalent.
If unit is raised greater than 8” (203 mm) or more; any non-combustible material can be used.
Table 6: Reduction in (B) Minimum Clearance from 1700 KI to 8” (203 mm) Mantel.
Type of protection Modied Clearance
A minimum of .013” (0.33mm) sheet metal spaced out 1” (25mm) by non-
combustible spacers. 12” (305 mm)
Ceramic tiles, or eqivalent non-combustible material on non-combustible
supports and spaced out 1” (25mm) by non-combustible spacers. 16⅛” (408 mm)
Ceramic tiles, or eqivalent non-combustible material on non-combustible
supports with a minimum of .013” (0.33mm) sheet metal spaced out 1”
(25mm) by non-combustible spacers.
12” (305 mm)
NOTES:
(1) Mantel protection must have at least 3” (75mm) edge clearance on all sides, except as provided in Note 4.
(2) If an adhesive is used to support non-combustible material, it shall not lose adhesive qualities at temperatures
likely to be encountered and shall not contribute a signicant combustible load.
(3) Heat shield mounting hardware attached to combustible materials must be placed at the lateral extremities of
the shield.
(4) Minimum clearance to unprotected walls and ceilings must be maintained.
Table 7: 1700 KI Insert Minimum Fireplace Size.
Masonry Zero Clearance
Minimum Depth 18” (457 mm) 18½” (470 mm)
Minimum Width at back of replace 22⅜” (568 mm) 23” (584 mm)
Minimum Width at front of replace 27” (686 mm) 27¼” (692 mm)
Minimum Width at front of replace to include shroud 36” (915 mm) 36” (915 mm)
Minimum Height 19¼” (489 mm)**
or 19¾” (502 mm) 20” (508 mm)
** If the masonry lintel height is only 19¼” (489 mm) to 19¾” (502 mm) refer to instaLLation - Modifications for
instaLLation with 19¼” (489 MM) high LinteL - insert
B
A
D
C
Adjacent wall
F
E
Table 5: 1700 KI Insert Clearance to Combustibles.
13

Specifications
dimEnsions - 1200 Ki insErt:
Figure 5: 1200 KI Insert Dimensions.
28 1
4
"
715
46"
1166
33 1
2
"
850
20"
508
18 1
2
"
472
22"
561
27"
687
36"
916
13 1
4
"
336
22 1
2
"
573
20 1
4
"
514
19 1
2
"
493
19 1
2
"
or
[483]
19"
497
20 3
4
"
529
5"
128
15 3
4
"
400
14

Specifications
dimEnsions - 1700 Ki insErt:
28 1
4
"
715
20"
508
18 1
2
"
472
33 1
2
"
850
46"
1166
20 3
4
"
526
19 1
2
"
or
[483]
19"
497
24 3
4
"
627
24"
607
17 3
4
"
450
27"
686
20 1
4
"
515
5"
126
36"
916
22"
561
27"
687
Figure 6: 1700 KI Insert Dimensions.
15

Installation
rEmoval from pallEt:
• Remove the bricks from the unit before starting.
• Remove the two (2) lag bolts (shown in Figure 7) that secure the unit to the pallet from inside the
rebox.
Note: Before the bricks are re-installed, rivets (Figure 8)
must be placed in the two holes where the lag bolts were
removed in the rebox . This is done to make unit burn
more efciently.
Figure 8: Rivet.
Figure 7: Bolts to remove.
modifications for installation witH 19” (484mm) HiGH lintEl:
Insert Cabinet Top
Air Deflector
Figure 10: Removing Air Deector onto Cabinet Top.
Figure 9: Removing Cabinet Top from Unit.
The KI has a factory height of 19½” (496mm) and it can
be reduced to 19” (483mm) by modifying the cabinet
top and mounting position
Insert Unit:
1. Remove the thirteen T-20 screws holding the cabinet
top in place (refer to Figure 9)
2. Remove the cabinet top and ip it onto its top.
3. Remove the Air Deector (shown in Figure 9) by
removing the two (2) T-20 screws.
4. Re-install the cabinet top onto the unit. The screw
holes along the top of the unit should now line up
with the top set of holes on the cabinet top.
16

Installation
masonry firEplacE installation:
Installation must be completed by a certied professional in order for warranty to
be valid.
Install only in a masonry replace with a good-condition chimney at least 15 ft (4.6 m) high, both of
which have been constructed in accordance with the building code. Refer to Tables 4 and 7 for minimum
masonry replace dimensions. Be sure the replace and chimney are clean and sound without any cracks
or loose mortar. Do not remove any bricks or mortar from the replace.
If there is a combustible oor in front of the
masonry replace, the replace insert must
be 8” (203 mm) above the combustible
oor, and oor protection must be provided
18” (457 mm) in front of the replace insert
and 8” (203 mm) to each side of the unit.
Refer also to sPecifications - cLearances to
coMbustibLes - 1200 Ki insert and sPecifications
- cLearances tocoMbustibLes - 1700 Ki insert.
1. Remove any replace damper or fasten
in a permanent open position.
2. (IN CANADA) The stove is vented with
a 6” stainless steel liner that goes directly to
the top of the chimney and is covered with
a rain cap. The chimney top is sealed with
a ashing or steel plate that supports the
weight of the chimney liner. The installation
must conform to the liner’s manufacturer’s
instructions.
This replace must be installed with a
continuous liner of 6” diameter (CANADA
ONLY) extending from the replace insert to
the top of the chimney. The chimney liner
must conform to the class 3 requirements of
ULC-S635 Standard for Lining Systems for
Existing Masonry or Factory-Built Chimneys
and Vents, or ULC-S640 Standard for Lining
Systems for New Masonry Chimneys.
(IN U.S.A.)The appliance when installed,
must follow local building codes, in the
absence of local building codes, with the
current NFPA 211 Standard for Chimneys,
Fireplaces, Vents, and Solid Fuel-Burning
Appliances.
Floor
Protection
Combustible Floor
Masonry Fireplace
8"
(203 mm)
Rain Cap
Steel Plate or Flashing
Flexible or Rigid 6"
Stainless Steel Liner
Mantel
Top Facing
Damper Removed
or Fastened Open
Sheet Metal Screws
Fastening Collar to
Stainless Steel Liner
Surround Panel
USA 16” (406 mm)
CND 18” (450 mm)
Figure 11: Insert Installation into existing replace with
hearth.
17

The ue collar is removable for installations
into replaces with low openings.
a) Remove the rear two (2) secondary
air tube and C-Cast Ceramic Bafes,
if installed (see c-cast ceraMic baffLe
instaLLation). Remove the secondary air
tubes by placing a screwdriver (any style
except at head) into one of the air holes
and tapping it with a hammer/mallet to
the left.
b) Unscrew the two (2) nuts on top of
the inside of the rebox, using a 9/16”
wrench or socket (see Figure 14). The
Flue Collar Clamps will slide off the bolts.
c) Pull the removable ue collar off the top
of the unit.
d) Attach the ue collar to the venting pipe
using sheet metal screws.
e) Push the unit into place while trying to
keep the collar attached to venting close
to the opening on the top of the unit.
Combustible Floor
Masonry Fireplace
USA 16” (406 mm)
CND 18” (450 mm)
1" (25mm)
Non-Combustible Board (K 0.84)
Figure 13: Insert Installation into existing oor level
masonry replace.
Installation
Floor Protection
Combustible Floor
Masonry Fireplace
8"
(203 mm)
USA 16” (406 mm)
CND 18” (450 mm)
Figure 12: Insert Installation into existing replace without
hearth.
f) Place the Collar Puller, over the two bolts of the Flue Collar
and pull it into place (see Figure 14). Ensure that the
bolts are to the left and right of the hole. If they are not,
the front secondary air tube will need to be removed in
order to install or remove the C-Cast Ceramic Bafes.
g) Slide the Flue Collar Clamps and washers over the bolts,
and screw the nuts back onto the bolts.
h) Re-install C-Cast Ceramic Bafes and the rear two (2)
secondary air tube (see c-cast ceraMic baffLe instaLLation).
3. There are four (4) leveling legs (shown in Figure 15), two
(2) on each side, one at the back and one at the front of the
unit. Adjust the legs using a ⅜” wrench to ensure the unit is
stable.
Figure 14: Attaching removable ue collar.
Firebox Top
Cut-away
Vent pipe
Removable
Flue Collar
Collar Puller
Gasket
Flue Collar Clamp
Washer
Nut
18

Installation
Figure 15: Removable ue collar in place.
Figure 16: Leveling legs.
surround panEl sEalEd installation for usa only:
Note: Though this is an allowable installation, we do not recommend it because of the possibility of poor
draft, and therefore poor stove performance.
Before starting this type of installation refer
to instaLLation - Masonry firePLace instaLLation
- insert for additional information. For
clearances refer to sPecifications - cLearances
tocoMbustibLes - 1200 Ki insert and
sPecifications - cLearances tocoMbustibLes -
1700 Ki insert.
1. Before the face plate is installed onto
the unit, glue a 6” (150mm) wide R20
berglass insulation strip around the
perimeter of the back of the panels using
RTV silicon or stove gasket cement.
When the face plate is installed onto
the unit the insulation must overlaps the
replace opening to form a seal between
the masonry replace and the unit’s face
plate. Let the silicon or cement dry.
2. To make the installation of the surround
panel onto the unit easy have the unit 6”
(150mm) out from the replace,
3. Push the insert into the replace, allowing
the insulation to form a seal between
the panels and the replace. Tuck any
exposed insulation behind the face plate. Figure 17: Installation with Surround Sealed.
Masonry Fireplace
Mantel
Damper Removed
or Fastened Open
Surround Panel
USA 16” (406 mm)
CND 18” (450 mm)
Insulation Around the
Back of the Face Plate
NOTE: To use this type of installation we
recommend your chimney have a minimum
cross-sectional area of 28 and a maximum of
144 square inch. If it is not within this range
your chimney may not have sufficient draw
for the fireplace to operate correctly.The
required cross-section may vary depending
on climate and if the chimney is inside (better)
or outside.
4. Screw or nail the provided metal plate with the
wording “THIS FIREPLACE HAS BEEN ALTERED
TO ACCOMMODATE A FIREPLACE INSERT AND
SHOULD BE INSPECTED BY A QUALIFIED PERSON
PRIOR TO THE RE-USE AS A CONVENTIONAL
FIREPLACE.” to the inside of the replace.
19

Installation
installation usinG a blocK-off platE for usa only:
If this unit is to be installed into a masonry replace or a zero-clearance replace with a direct connection
you must install a non-combustible seal-off device such as a block-off plate or damper adapter. By
installing a block-off plate you seal the chimney, ensuring that no smoke enters the home and sealing the
chimney to encourage draft. To construct a block-off plate follow the below steps.
1. Determine where the block-off plate will be installed; above the top of the rebox (it must be high
enough to easily install the connection pipe) but below the damper area. Look for a location that is
A
B
C
D
Front of fireplace opening.
A
B
C
level and in an area where the plate can be mounted easily.
The measurement that will be needed are as followed (refer
to Figure 17 and 18):`
A - The width at the front of the rebox at the height where
the block-off plate will be installed.
B - The width at the back of the rebox at the height where
the block-off plate will be installed.
C - Then depth of the block-off needed (the distance
between A and B).
D - The distance of the center of the ue to the front of the
replace opening. Refer to Step 3.
NOTE: In general masonry replaces have square reboxes
while zero-clearance (metal) replaces have domed rebox
tops. Therefore zero-clearance block-off plates may be more
difcult to install. Insulation may be used around the edges
to simplify sealing the plate.
2. Create a cardboard template of the dimensions with 2” (51
cm) wide anges on each side. These anges will be used to
mount the block-off plate to the inside of the rebox. Bend
the anges downwards on the template and place it inside
the replace. Continue on if the template ts correctly in
its planned location. If the template does not t, make a
new template with the required corrections until it does t
correctly.
3. With the template in place, mark the location for the center
of the ue pipe when the unit is in place. If installing a
1200 KI the distance will be approximately 8¼” or 9 15/16”
back from the replace opening. If installing a 1700 KI the
distance will be approximately 12¾” or 14 7/16” back from
the replace opening. Remove the template and cut a 6¼”
diameter hole centered on this mark.
4. Using the template make the block-off plate of 24 gauge or
thicker steel. Drill two (2) holes in each ange for mounting
the plate.
5. Mount the block-off plate using masonry screws in a masonry
Figure 18: 3D of Dimensions needed from
the Fireplace.
Figure 19: Layout of the Block-Off Plate.
20