EPH R17-RF User manual

For use in normal environments.
EPH Controls Ireland
Sitecast Industrial Estate, Pouladu,
Cork, T12 W665, Ireland
[e-mail] www.ephcontrols.com
EPH Controls UK
Unit E4, Welland Business Park, Valley Way, Market Harborough,
Leicestershire, LE16 7PS, United Kingdom
[e-mail] www.ephcontrols.co.uk
R17-RF - 1 Zone RF Timeswitch Installation Instructions
Page 1 of 2
 Before commencing any work on the electrical connections, you must rst disconnect the timeswitch
from the mains. None of the 230V connections must be live until the installation has been completed
and the housing is closed. Only qualied electricians or authorised service sta are permitted to open
the timeswitch. Disconnect from mains supply in the event of any damage to any buttons.
 There are parts that carry mains voltage behind the cover. The timeswitch must not be left unsupervised
when open. (Prevent non specialists and especially children from gaining access to it.)
 If the timeswitch is used in a way not specied by the manufacturer, its safety may be impaired.
 Ensure that this wireless enabled timeswitch is installed 1 metre from any metalic object, television,
radio or wireless internet transmitter.
 Prior to setting the timeswitch, it is neccessary to complete all required settings described in this section.
 Never remove this product from the electrical baseplate. Do not use sharp tools to push any button.
CAUTION! Installation and connection should only be carried out by a qualied
person and in accordance with national wiring regulations.
Type
EN60730
1C IP20
EN60529
50
°C
0
122
°F
32
5-95%RH
160.5
100
This timeswitch can be mounted in the following ways: 1. Directly wall mounted 2. Mounted to a recessed conduit box
This 1 zone RF timeswitch is designed to provide
ON/OFF control for 1 zone, with the value added
application of in built frost protection.
Important: Keep this document
1
34
5 6
2
20170302_AW1077_R17-RF_InsIns_JW

For use in normal environments.
R17-RF - 1 Zone RF Timeswitch Installation Instructions
Page 2 of 2
EPH Controls Ireland
Sitecast Industrial Estate, Pouladu,
Cork, T12 W665, Ireland
[e-mail] www.ephcontrols.com
EPH Controls UK
Unit E4, Welland Business Park, Valley Way, Market Harborough,
Leicestershire, LE16 7PS, United Kingdom
[e-mail] www.ephcontrols.co.uk
20170302_AW1077_R17-RF_InsIns_JW
1. Factory default settings
Contacts: Volt free contact
Program: 5/2D
Backlight: On
Keypad: Unlocked
Frost Protection: O
Clock type: 24 Hr Clock
Day-Light Saving
Power Supply: 230 Vac
Ambient Temp: 0~35°C
Contact Rating: 250 Vac 3A(1A)
Program Memory
backup: 1 year
Battery: 3Vdc Lithium LIR 2032
Backlight: Blue
IP rating: IP20
Backplate: British System Standard
Pollution degree 2: Resistance to voltage surge 2000V
as per EN 60730
Automatic Action: Type 1.S
Software: Class A
2. Specications & wiring
200-240Vac
50Hz-60Hz CONTACT RATING: 250Vac~/3(1)A
Lower the cover on the front of the timeswitch. There are four hinges
holding the cover in place.
Between the 3rd and 4th hinges there is a circular hole. Insert a ball point
pen or similar object to master reset the timeswitch.
After pressing the master reset button, the date and time will now need to
be reprogrammed.
5. Master reset
If mains voltage output is required, terminals L & 1 must be electrically
linked. The cable link is provided with this timeswitch.
Contents
1. Factory default settings
2. Specications & wiring
3. Setting the date & time
4. Frost protection
5. Master reset
3. Setting the date and time
Press
Press
Press
Press
Press
Press
Lower the cover on the front of the timeswitch.
Move the selector switch to the CLOCK SET position.
Press the or buttons to select the day.
Press the or buttons to select the month.
Press the or buttons to select the year.
Press the or buttons to select the hour.
Press the or buttons to select the minute.
Press the or buttons to select 5/2D, 7D or 24H
The date, time and function are now set.
Move the selector switch to the RUN position to run the program, or to
the PROG SET position to change the program setting.
Selectable range 5~20°C
This function is set to protect pipes against freezing or to prevent low room
temperature when the timeswitch is programmed to be OFF or is manually
OFF.
Frost protection can be activated by following the procedure below.
Move the selector switch to the RUN position.
Press both the and buttons for 5 seconds, to enter selection mode.
Press either the or buttons to to turn On or turn O frost protection.
Press button to conrm
Press either the or buttons to increase or decrease the desired frost
protection setpoint.
Press to select.
Zone 1 will be switched ON in the event of room temperature falling below
the frost protection setpoint.
O
4. Frost protection function
RUN
CLOCK
SET
PROG
SET
OFFCOM ON