YOODA AURA Series Configuration guide

Illustrations (from the top):
Fig. 1. 5-channel AURA wall-mounted remote control with timer (AURA_5RwT)
Fig. 2.1-channel AURA wall-mounted remote control with timer (AURA_1RwT)
Radio receiver range is a variable value and can differ from declared values depending on conditions in which device
operates. Possible sources of changes in range are building construction, interference caused by other radio transmitters
etc.
LCD display
Currently supported
channel (5RwT only)
Current
work mode
FR
MAN
AUTO
TH SAWETUMOSU
Actual
time
Low battery
message
Direction movement
of roller shutter
Activaiting days
in automatic mode
1. Control:
can control single motor, or a group
of up to 20 motors on each channel
2. Range:
200 meters outdoor,
35 meters indoor
3. Battery:
CR2430
4. Power supply:
3 V
5. Dimensions:
80 x 80 x 17 mm
6. Transmitting power:
10 mW
7. Operating temperature:
from 0°C to 50°C
8. Protection degree:
IP 30
In order to fully explore available functions of AURA series please take a moment and read this manual before using the device.
AURA transmitters are compatible with all YOODA brand devices.
AURA_1RwT | AURA_5RwT
www.sukcesgroup.pl
1. General information
2. Detailed description
1
1-channel transmitter with timer
or 5-channel transmitter with timer
(front)
DOWN buttonUP button
STOP button
Timer
programming button
(L1)/Channel
Configuration change button
(P1)/Channel +
P2
programming button

1. For channel to work correctly when remote is set to automatic mode, it has to be activated. If automatic mode is
chosen for the channel and the channel number is flashing, that means device does not work in this mode.
2. Difference between automatic time of roller shutter opening and closing cannot be shorter than 32 minutes. In case of
smaller than minimal time difference fault message will appear and none of the changes will be saved.
3. Pressing UP or DOWN button in automatic mode will show currently set opening / closing time and symbol of current
process.
4. Estimated battery lifespan is 1 year if the device runs 4 commends a day in average.
5. Batteries should be changed when device stops reacting to commands.
6. When replacing the battery, pay attention to the correct polarity.
7. When on display all channels are selected remote controls all programmed devices on all channels at the same time.
No programming functions can be performed on group channel. All devices programmed to any other channel can be
controlled on group channel without additional programming.
8. For all devices, that are programmed on all the channels, to work at programmed time, group channel and automatic
mode should be chosen.
Weekly programator can be set up in 4 ways (opening and closing time for selected option):
- individual days
- MO-FR
- MO-SA
- whole week
Batteries contain substances that may be hazardous to health and may pollute the environment. Used batteries should
be disposed of properly.
1. Manual work mode: standard mode without using time programming function.
2. Automatic mode: standard mode with activated automatic work time.
3. Random work mode: automatic mode with random time of work (15 minutes difference from programmed time).
4. Work mode changes for all channels.
By pressing
programming button P2
for about 3 seconds work mode
will change to manual mode.
By pressing
programming button P2
for about 3 seconds work mode
will change to automaticl mode.
By pressing
programming button P2
for about 3 seconds work mode
will change to random mode.
Pressing the programming button P2
again switches between modes.
1. Each channel can be activated or deactivated in automatic mode.
2. If channel is deactivated transmitter will not control programmed radio receiver at preset time.
3. Channel is deactivated if its number is flashing.
4. In default mode all channels are active in automatic mode.
By pressing
programming button P2
for about 3 seconds work mode
will change to automatic
or random mode.
Choose the channel
by pressing L1 or P1 button.
By pressing P1 button
for about 5 secondsn channel will
deactivate in automatic mode.
Channel number is flashing.
Another pressing P1 button
for about 3 seconds
will activate automatic mode
on chosen channel.
Channel displays constantly.
3. Changing work mode
4. Activating channels in automatic mode
2

1. Difference between automatic time of roller shutter opening and closing cannot be shorter than 32 minutes. In case of
smaller than minimal time difference fault message will appear.
2. Changes to opening and closing time can be done only in automatic mode.
3. Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off
from
time setting mode without saving any changes.
4. Group channel needs to chosen for transmitter to control all devices at the same time. That applies to all working
modes.
5. If while setting time of automatic opening or closing ‘--:--‘ symbol appears, it means that this time is not active in
automatic mode.
6. To leave time programming mode without saving any changes press STOP button.
The below steps need to be repeated for all five channels during the same programming.
PERFORMED ACTION
TIME PROGRAMMING FOR OPENING AND CLOSING
DISPLAY MESSAGE
By pressing
programming button P2
for about 3 seconds work mode
will change to automatic mode.
Press
L1 button.
Using UP and DOWN buttons
set hour.
Press
L1 button.
Switch to opening minute setting.
Minute starts to flash.
The set time will
appear on the display
Opening time will display.
Hour starts to flash.
AUTO symbol
will display.
Press and hold L1 button
for about 3 seconds. Opening time
will display.
AUTO
AUTO
AUTO
AUTO
AUTO
Time can be set only when device is in manual working mode.
Longer than 10 seconds pause between series of button clicks during programming will cause device to switch off from
time setting mode without saving any changes.
By pressing L1 button switch
to current day of the week.
Using UP and DOWN buttons
set current day of the week.
Press P1 button
to confirm all the changes.
By pressing
programming button P2
for about 3 seconds work mode
will change to manual mode.
Press and hold L1 button
for about 5 seconds
(hour starts to flash).
Using UP and DOWN
buttons set hour.
By pressing L1 button
switch to minute setting.
Using UP and DOWN buttons
set minute.
5. Setting current time
6. Changing time settings for automatic opening and closing
7. Setting automatic opening and closing time
3
Su
Mo Tu We Th Fr
Mo Tu We Th Fr
Mo Tu We Th Fr
Mo Tu We Th Fr

Using UP and DOWN buttons
set minutes..
Press
L1 button.
By pressing UP/DOWN button we can set the
weekly programator in 4 ways:
- individual days
- MO-FR
- MO-SA
- whole week
Switch to closing hours setting
by pressing P1 button.
Press
L1 button.
Switch to closing minute setting.
Minute starts to flash.
Using UP and DOWN buttons
set hour.
The set hour
will appear.
The set minute
will appear.
Days of week
start to flash.
The set days will appear
on the display
Using UP and DOWN buttons
set minutes.
Press P1 button
to confirm the set time.
The set closing hour will appear (in case 5RwT
remote hour of the next channel will display).
After programming press STOP button
to end the automatic time setting.
The actual time
will appear.
The set minutes
will appear
Closing time will display.
Hour starts to flash.
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
1. Way of programming first transmitter depends on type of radio receiver. When programming first transmitter please
follow instruction of the device that is going to be controlled by the transmitter.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
3. Programming transmitter using this ethod will result in deleting receiver memory.
Turn on power supply
or press microswitch
(for 2 sec.) when
power is on.
Motor will make a sound.
Roller shutter will make
an up/down move.
Motor will make
a sound.
Press
programming button
(P2) on the remote.
or
Roller shutter
will make an
up/down move
and the motor
will make a few
short sounds.
Motor will
make a sound.
Press
programming button
(P2) on the remote.
Press UP button.
9. Programming first transmitter to R-type motors
8. Keyboard lock
4
Mo Tu We Th Fr
AUTO
Mo Tu We Th Fr
AUTO
Mo Tu We Th Fr Sa Su
Mo Tu We Th Fr Sa Su
Mo Tu We Th Fr Sa Su
Mo Tu We Th Fr Sa Su
Mo Tu We Th Fr Sa Su
Sa
Mo
Press simultaneously and
hold L1 and P1 buttons
four about 4 seconds.
LOCI- symbol will appear - the
keyboard will be lock.
Press simultaneously
L1 and P1 buttons
four about 4 seconds.
LOCI- symbol will appear - the
keyboard will be unlocked.