Epilog Laser Fusion User manual

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 1 of 10
EPILOG LASER
16371 Table Mountain Parkway
Golden, Colorado 80403
Phone [phone]
FAX [phone]
www.epiloglaser.com
Adjusting the Table Level
For the Epilog Fusion and FiberMark Fusion
9/10/2014
Requirements:
Tools:
•3/32” Allen Wrench
•Manual Focus Gauge
When to use this document:
•Uneven power in various areas of the table.
•Reduction in quality in various areas of the table.
•General reduction in power or quality.
•Inconsistent or Inaccurate Auto Focus.
•When instructed by Epilog Tech Support.
Overview:
This procedure will guide you through the process of properly checking and
adjusting the table level on the Epilog Fusion. This will ensure proper focus on every
point of the engraving area.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 2 of 10
Procedure A: Check Table Level
Step 1: Position Lens Carriage in Reference Corner
With the engraver powered ON and the Cutting Table removed, use the Up and
Down Arrow Keys on the Key Pad to place the engraver into Jog mode. Use the
Joystick to move the Lens Carriage to the Back Right Corner of the engraver.
Step 2: Place Manual Focus Gauge
Place the Manual Focus Gauge on the Lens Carriage.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 3 of 10
Step 3: Focus on Reference Corner
Use the Up and Down Arrow Keys on the Key Pad to place the engraver into
Focus mode. Use the Joystick to move the Table until it just touches the Manual Focus
Gauge.
Step 4: Check Focus on Each Corner
Use the Up and Down Arrow Keys on the Key Pad to place the engraver into Jog
mode. Use the Joystick to move the Lens Carriage to each corner of the engraver. If the
table is still barely touching the Manual Focus Gauge in each corner, the table level is
good. If the table drops away or rises up as you move the Lens Carriage, please
continue to the next procedure.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 4 of 10
Determining Which Corners Need to Be Leveled
After completing Procedure A, you should be able to determine which of the
three adjustable corners need to be leveled. The Rear Right Corner cannot be adjusted
and will be used as a reference point to adjust each of the other corners. A corner will
need to be adjusted if the Manual Focus Gauge is a different distance away from the
Table then it was in the Rear Right Corner.
Touching Gap Contact
Once you have determined which corners need to be adjusted, please follow
corresponding procedures. Please see the table below.
If you determine that the table is level, but power or quality problems persist; please
contact Epilog Tech Support at [phone].
The following procedures require that you complete
Procedure A
before starting. Do
not use focus mode after completing Procedure A – Step 3.
Do not use a Bubble, Laser, or Gravity Level. The table must be level to the Movement
Axis of the engraver rather than gravity.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 5 of 10
Procedure B: Adjusting the Front Corners
Step 1: Move the Lens Carriage.
Use the Up and Down Arrow Keys on the Key Pad to place the engraver into Jog
mode. Use the Joystick to move the Lens Carriage to whichever Front Corner of the
engraver requires adjustment.
Step 2: Open the Front Panel
Open the Front Drop-Down Panel of the engraver so that you can access the
underside of the table.
Step 3: Locate the Table Level Adjuster
Look at the bottom of the table and locate the Table Level Adjusters. There is
one on the Left and one on the Right sides of the table.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 6 of 10
Step 4: Loosen the Lock Screws
Select the appropriate Table Level Adjuster for the corner that you wish to adjust.
Locate and loosen the two 3/32” Allen screws on the bottom of the Table Level Adjuster.
NOTE: Do not completely remove these screws.
Step 5: Make the Adjustment
Locate the Adjustment Wheel on the Table Level Adjuster. Turning the wheel to
the Right will raise the corner. Turning the wheel to the Left will lower the corner. Turn
the wheel until the corner of the table is lightly touching the Manual Focus Gauge.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 7 of 10
Step 6: Lock the Adjustment Wheel in Place.
Tighten the two 3/32” Allen screws on the bottom of the Table Level Adjuster.
This will lock the level in place.
Procedure C:
Step 1: Move the Lens Carriage
Check the table level on each corner of the engraver.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 8 of 10
Step 2: Remove the Rear Exhaust Weldment
Locate and remove the 4 Philips head screws on the rear of the engraver to
remove the exhaust weldment.
Step 3: Locate the Left Rear Table Level Adjuster

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 9 of 10
Step 4: Loosen the Lock Screws
Locate and loosen the two 3/32” Allen screws on the bottom of the Table Level
Adjuster. NOTE: Do not completely remove these screws.
Step 5: Make the Adjustment
Locate the Adjustment Wheel on the Table Level Adjuster. Turning the wheel to
the Right will raise the corner. Turning the wheel to the Left will lower the corner. Turn
the wheel until the corner of the table is lightly touching the Manual Focus Gauge.

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014 pg. 10 of 10
Step 6: Lock the Adjustment Wheel
Tighten the two 3/32” Allen screws on the bottom of the Table Level Adjuster.
This will lock the level in place
Step 7: Replace Exhaust Weldment