Epson 740c - PowerLite XGA LCD Projector Dimensions

Page 1 of 1
EPSON PRODUCT SUPPORT BULLETIN
Date: 8/30/2007 Originator: DS
PSB #: PSB.2007.08.001 Authorization:
Reference: N/A Total Pages: 1
Product(s): Epson Projectors with an HD-15 VGA Analog/Component Input
Subject: Elmo HV-110XG Document Camera and Projector Compatibility
This bulletin was created to inform you of an operational issue with the Elmo HV-110XG
Document Camera when initially connected to an Epson projector.
Problem:
When attempting to use the Elmo HV-110XG Document Camera connected via the VGA HD15
connection to display content from its document bed. When connected to the projector, the
projector displays only the Blue Screen - No Signal message and will blink off and on or
display just the Blue Screen - No Signal message. When a computer is connected to the Elmo
HV-110XG Document Camera and switched to Pass-Through mode, the computer image is
displayed correctly by the projector. When switching back to the document table source of the
Elmo HV-110XG Document Camera, the problem returns. The Elmo HV-110XG Document
Camera puts out a Progressive Scan 20fps signal to the projector's VGA Analog port. This
signal is detected at 15 kHz Vertical and 291.8 kHz Horizontal frequencies which are beyond
projector sync specifications.
Solution:
With the Elmo HV-110XG Document Camera powered on and connected to the projector via
the VGA computer cable, access the Computer1/Computer2 setting in the projector menu
system and select the Component setting within the appropriate connection. This will allow
the Elmo HV-110XG Document Camera and projector to sync and the projector to display the
image of the document camera bed and its contents. However, the image will have a pink
cast. To eliminate the pink cast, change the projector setting from Component to RGB then to
Auto and exit from the menu. The projected image will now look normal. This will now allow
the Elmo HV-110XG Document Camera to sync and display the image properly to any other
connected Epson projector without having to change the projector settings.

Page 1 of 144
PSB.2004.10.002
EPSON PRODUCT SUPPORT BULLETIN
Date: 10/08/2004 Originator: DS
PSB #: PSB.2004.10.002 Authorization:
Reference: TI 04-46e Rev. A Total Pages: 14
Product(s): EMP NS Connection, EMP Network Manager, EMP Monitor,
EMP Multi Screen Adjustment, Cinema Color Editor, VCOM Driver
Subject: Evaluation results of Epson Projector PC applications tested in Windows XP
with SP2.
The purpose of this bulletin is to provide information on Epson PC projector applications tested
under the Windows XP SP2 (Service Pack2) environment.
Description:
Information is provided about the evaluation results and recommendations for Epson PC
projector applications functionality in Windows XP SP2 Firewall environment.
Reason:
Compatibility testing for functionality of EMP NS Connection, EMP Network Manager, EMP
Monitor, EMP Multi Screen Adjustment, Cinema Color Editor, VCOM Driver in the Windows
XP SP2 environment.
Results of Windows XP SP2 installation:
Installing SP2 on PCs did not disturb the installation of the above software applications.
Also, the application software can be installed on PCs where SP2 or earlier versions are
installed without any issues.
The information contained in the following pages provides details for executing the
applications in Windows XP SP2.

Page 2 of 144
PSB.2004.10.002
Executing the Software:
When executing the software noted below for the first time after SP2 installation completes,
the following security alert messages are displayed:
[EMP NS Connection]
Security alert screen (EMP NS Connection)
[EMP Network Manager]
Security alert screen (EMP Network Manager)

Page 3 of 144
PSB.2004.10.002
[EMP Monitor]
Security alert screen (EMP Monitor)
[EMP Multi Screen Adjustment]
Security alert screen (EMP Multi Screen Adjustment)
The Security Alert screen for EMP Multi Screen Adjustment is shown after clicking the
Auto button of Network or clicking the Add button after entering an IP address in the
IP Address box.

Page 4 of 144
PSB.2004.10.002
[Cinema Color Editor]
Security alert screen (Cinema Color Editor)
The functions of the three buttons displayed in the security alert screen are explained
below.
[Keep Blocking] --- Enables you to register a started application in the “Exceptions”
program of the Windows Firewall. The network port that the
application uses is blocked. By selecting this button once, this
security alert message will not be shown when starting the
application next time.
[Unblock] ------------- Enables you to register a started application in the “Exceptions”
program of the Windows Firewall and unblock the network port that
the application uses. By selecting this option once, this security alert
message will not be shown when starting the application next time.
[Ask me later]-------- When you want to select both buttons above or select either one
later, this button is selected. The started application is not registered
in the “Exceptions” program of the Windows Firewall and the
network that the application uses is not unblocked. However, when
restarting the application, the same security alert message is shown.
•PC applications will work normally on Windows XP with SP2 if the “Unblock
Item” is selected when the security alert screen is shown.
For the detail operation information of each application, please refer to the following:

Page 5 of 144
PSB.2004.10.002
Operating Status Report
When selecting the Keep Blocking button, the security alert message is closed and the
main screen of each application is displayed.
[EMP NS Connection Application]
Port 3620 is necessary for searching for projectors. If this port is blocked, projectors are not
detected.
The other applications operate normally. However, there is a case that execution of
automatic search disables automatic detection. This occurs when projectors are registered
for automatic detection in EMP Monitor before installing SP2, then the registered projectors
may not be detected again after SP2 installation. Therefore it is recommended to select
Unblock in the security alert screen.
If “Keep Blocking” has been selected when starting the application for the first
time, and the blocking needs to be removed, complete the execution of the application and
proceed with unblocking as follows:
a.) Start the Windows Security Center. Double click the icon in the shape of a shield that
is always displayed on the taskbar after the installation of SP2.
Windows Security Center screen
b.) Select and start Windows Firewall

Page 6 of 144
PSB.2004.10.002
Windows Firewall screen
[Caution]
In case the check box
for Don’t allow
exceptions
is checked (this box is
not checked at the
initial setting), a
network port for
software is not
unblocked even though
the software is checked
on Exceptions.
Make sure this option is
not selected.

Page 7 of 144
PSB.2004.10.002
c.) Select the Exceptions tab and display exceptions program.
•Exceptions screen
d.) Check the check boxes for the software you don’t want to block.
[Caution]
If this check box is
not checked, the
security alert
screen is not
displayed when
starting software.

Page 8 of 144
PSB.2004.10.002
[EMP NS Connection] •Check EasyMP Software box
Unblock screen (EMP NS Connection)

Page 9 of 144
PSB.2004.10.002
[EMP Network Manager Application]•Check EPSON Projector box
Unblock screen (EMP Network Manager)

Page 10 of 144
PSB.2004.10.002
[EMP Monitor Application]→Check EasyMP.net Software box
Unblock screen (EMP Monitor)

Page 11 of 144
PSB.2004.10.002
[EMP Multi Screen Adjustment Application]→Check EPSON Projector Software for
Multi Screen box
Unblock screen (EMP Multi Screen Adjustment)

Page 12 of 144
PSB.2004.10.002
[Cinema Color Editor Application] ---> Check Cinema Color Editor.
Unblock screen (Cinema Color Editor)
By following the above procedure, the network port that each application uses is unblocked
and they can operate normally.

Page 13 of 144
PSB.2004.10.002
Corresponding program name to PC applications
PC Application Program name
EMP NS Connection EasyMP Software
EMP Network Manager EPSON Projector
EMP Monitor EasyMP.net Software
EMP Multi Screen Adjustment EPSON Projector Software for Multi Screen
Cinema Color Editor Cinema Color Editor
When selecting the Unblock button:
The Security Alert screen is closed and the main screen is displayed. Then the search result
is displayed.
When selecting the Ask Me Later button:
Port 3620 which is used by EMP NS Connection and is necessary for discovering projectors
is blocked, and projectors are not detected.
The other applications operate normally. However, there is a case where execution of
automatic search disables automatic detection. This occurs when projectors are registered
for automatic detection in EMP Monitor before installing SP2, the registered projectors may
not be detected after SP2 installation.

Page 14 of 144
PSB.2004.10.002
VCOM Driver
The following message is shown after the VCOM driver is installed on your PC.
Select “No, not this time” item and continue the Plug&Play of the device.
8.) Notes:
When you add the program to Exceptions list, the program can receive network
communication from outside. This may cause a security risk such as exposure to a virus
attack.