Epson PictureMate - Compact Photo Printer Guide

Using PictureMate
With a Computer
CPD-17895R2
Printed in XXXXXX XX.XX-XX XXX

Follow These Easy Steps
To use PictureMate™ with your computer, you’ll need to:
Install the software on your computer
from the PictureMate CD.
Follow the steps in this booklet.
Connect PictureMate to your computer.
The steps here tell you how and when
to connect.
View the on-screen
User’s Guide .
Click PictureMate User’s Guide right on
your computer screen for steps on using
PictureMate with your computer. It’s your
comprehensive guide to PictureMate.
Where To Get Help
If you need additional help with PictureMate, see “Where To Get Help”
in the Using PictureMate Without a Computer book.
PictureMate Accessories
You can purchase a PictureMate Print Pack
(with 100 sheets of PictureMate Photo Paper
and a PictureMate Photo Cartridge), a USB
cable, and other PictureMate accessories
from the Epson StoreSM at [phone] or
visit www.epsonstore.com (U.S. sales only).
In Canada, please call [phone] for
dealer referral.

1
Installing Software and Connecting PictureMate
To connect PictureMate, you’ll need this cable:
If you don’t already have a USB cable, you can buy one from your local
computer dealer or from Epson.
®See the inside back cover for details.
When you’re ready to start, see the section for your computer system:
■For Windows,
®see below.
■For Macintosh,
®see page 6.
Install PictureMate for Windows
First make sure PictureMate is NOT CONNECTED to your computer,
and REMOVE your memory card, if it’s inserted. Then:
1. Load a sheet of PictureMate Photo Paper,
glossy side up, against the right edge of the
paper feeder. Slide the edge guide against
the paper and open the output tray.
2. Press the POn button to turn on PictureMate.
3. Turn on your computer.
Type A to B
USB cable

2
4. Wait a minute for your computer to
start up, then insert the PictureMate
CD in your CD-ROM or DVD drive.
5. After a moment, you see this screen:
Read the license agreement and click
AGREE.
Note:
If you see a screen like this,
remove your memory card from
PictureMate and click the Xin the
upper right corner to close the screen,
if necessary.
Note:
If you see a screen like this,
click Cancel and disconnect
PictureMate from your computer.
Then turn off your computer and
begin again at step 3.
If you see a New Hardware Found
message at the bottom of your screen,
click the Xin the box to close it.

3
6. When you see this screen, click OK to begin installing your software.
7. When you see this screen, connect the square end of your USB cable to
PictureMate. Then connect the flat end of the USB cable to your
computer. (You can connect it to any open USB port.)
Note:
Make sure the PictureMate handle is pushed all the way down in back
before connecting the USB cable.
On Windows 98SE, you see an Add New Hardware Wizard screen. Click
Next, select the Search for option, and select CD-ROM drive. Follow the
on-screen instructions to finish installing the necessary software.

4
8. When you see this screen, click OK to print a 4 × 6-inch sample photo.
You see a progress screen as it prints. (If it doesn’t print, see page 12.)
Wait until printing finishes before continuing with step 9.
9. When printing finishes, click Next to install the on-screen User’s Guide
and more software.
10. When you see this screen, you can install additional photo software:
Click Epson Software Film Factory, then click Install on the next
screen and follow the on-screen instructions.

5
Note:
If you are asked if you want to install QuickTime,
®click Yes and follow the
on-screen instructions; you don’t need a registration number. Also
uncheck the boxes for launching QuickTime and Film Factory™at the end
of their installations.
11. When you’re done installing software, click Exit. The registration screen
appears. Follow the on-screen instructions to register PictureMate.
12. You see a prompt to restart your computer. Click OK, then restart your
computer.
13. Remove and store your PictureMate CD.
You’re ready to store or print your photos! Insert your memory card or
open your photo file on your computer, as described in the on-screen
User’s Guide.
Double-click the PictureMate User’s Guide icon on your screen to view
the User’s Guide. Follow the steps there to use PictureMate with your
computer.

6
Install PictureMate for Macintosh
1. If you inserted a memory card, remove it from PictureMate.
2. Connect the square end of your USB cable to PictureMate. Then
connect the flat end of the USB cable to any open USB port on your
Macintosh.
3. Press the POn button to turn on PictureMate.
4. Turn on your Macintosh and wait a minute for it to start up.
5. Insert the PictureMate CD in your CD-ROM or DVD drive.
6. Double-click the PictureMate CD icon, if necessary, then
double-click PictureMate.

7
7. After a moment, you see this screen:
Read the license agreement and click AGREE.
8. When you see the Install Menu, click Install Printer Driver and
Utilities. Follow the on-screen instructions to install several programs.
Note:
With OS X, you’ll need to enter your password several times as you
install.

8
9. When you return to the Install Menu, click Install Optional Software.
You see this menu:
10. Click Epson Software Film Factory, then click Install on the next
screen and follow the on-screen instructions.
11. When you return from the Film Factory installation screens, click Back.
12. At the Install Menu, click Install Printer Manual to install your
on-screen User’s Guide.
13. When you’re done installing software, click Exit. The registration screen
appears. Follow the on-screen instructions to register PictureMate.
14. You see a prompt to restart your Macintosh. Click OK, then restart
your Macintosh.
After restarting, you must select PictureMate as your Macintosh printer.
See page 9 (Mac®OS X) or page 11 (Mac OS 9).