Epson Stylus Photo 750 User manual

USB User's Guide
Read this guide if using a shielded USB cable to connect
your EPSON printer to your computer.
4009524
S01-01

Copyright © 1998 by SEIKO EPSON CORPORATION,
Nagano, Japan

3
System Requirements
To use your printer through the printer’s built-in USB port,
you need the following:
❏Microsoft®Windows 98®pre-installed PC equipped with a
USB port, or an Apple®iMac®computer.
❏USB Interface Cable (shielded) C83623✽ from Series A 4-pin
(computer) to Series B 4-pin (printer)
cCaution:
Using other cables not covered by EPSON warranties
(especially cables more than 1.8 meters long) may cause the
printer to malfunction.
Note:
❏The asterisk (✽)is a substitute for the last digit of the product
number, which varies by country.
❏This cable may not be available in some countries.
❏For PC’s, you must have 10MB of free hard disk space to
install the USB Printer Device Driver and the printer software
❏For iMac computers, you must have 10MB of free hard disk
space to install the printer software

4
Connecting the USB Cable
Follow the steps below to connect your printer.
Note:
❏Install the ink cartridges before connecting the cable. See your
printer manual for instructions.
❏For PC’s, make sure that the Universal Serial Bus Controller is
working properly in the Device Manager before connecting the
USB cable. See your computer documentation for details.
1. Plug the appropriate end of the shielded USB cable into the
USB port on the back of the printer. (The end of the cable that
fits the printer is a different shape than the end that fits the
computer.)
2. Plug the other end into the computer’s USB port.
Note:
If you use a USB hub, EPSON recommends connecting the printer to
the first tier of the hub, otherwise the printer may malfunction. If the
printer does not work properly with the USB hub, connect the printer
directly to the computer’s USB port.

5
After connecting the printer to a PC, you must install the EPSON
USB Printer Device Driver and the printer software. See
“Installing the USB Software in Windows” on page 6.
After connecting the printer to an iMac computer, you must install
the printer software and select the USB port for your printer in
the Chooser. See “Installing the Printer Software in Your
Macintosh” and “Selecting Your Printer in the Chooser” in the
Setup & Daily Use guide.

6
Installing the USB Software in Windows
The USB Printer Device Driver is included in the Printer Software
CD-ROM shipped with your printer.
The installation program for the USB Printer Device Driver also
allows you to install the printer software. You do not need to
install the printer software separately.
1. Make sure Windows 98 is running.
2. Turn on your printer. The following dialog box appears.
3. Click Next and follow the instructions on the screen.

7
4. When the following dialog box appears, click Specify a
location and type D:\ win98 (if your CD-ROM drive uses a
drive letter other than “D”, substitute the appropriate letter).
Insert the printer software CD-ROM, then click Next.
5. Click Next to begin the device driver installation.
Type here.
Then click here.
Click here.

8
6. After the installation is completed, the following dialog box
appears. Click Finish.
7. The printer software installation automatically starts and the
following dialog box appears. Click Next.
Click here.
Click here.
This varies
depending
on your
printer
model.

9
8. When the dialog box below appears, click Next and follow
the instructions on the screen.
After the printer software is installed, EPSON Status Monitor 2
installation starts automatically. Follow the on-screen
instructions.
Click here.

10
9. To confirm that installation was successful, check to see if
“EPSON USB Printer Devices” appears in the Device
Manager. Click Start, point to Settings, and click Control
Panel. Then double-click System and click the Device
Manager tab.
Your printer is now ready to receive print jobs through the
USB port. For instructions on using your printer, see your printer
manual.
Check here.