Epson Stylus Pro GS6000 User manual

EpsonStylusProGS6000
Large Format Color Inkjet Printer
SERVICE MANUAL
SEIJ08001
Confidential

Confidential
Notice:
All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.
The contents of this manual are subject to change without notice.
All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly
appreciate being informed of them.
The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.
EPSON is a registered trademark of SEIKO EPSON CORPORATION.
General Notice: Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their
respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2008 SEIKO EPSON CORPORATION.
Imaging Products CS, PL & Environmental Management

Confidential
PRECAUTIONS
Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) Damage to equipment.
DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing
procedures preceded by DANGER Headings.
WARNING Signals a precaution which, if ignored, could result in damage to equipment.
The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.
DANGER
1. ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR
REPAIR PROCEDURES.
2. NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL
ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK.
3. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL
INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER
SUPPLY AND OTHER ELECTRONIC COMPONENTS.
4. WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURY FROM METAL PARTS WITH
SHARP EDGES.
WARNING
1. REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.
2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING
PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO
THE POWER SOURCE.
3. ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR
REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.
4. IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC
WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.
5. REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECOND-
SOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.
6. WHEN AIR DUSTER IS USED ON THE REPAIR AND THE MAINTENANCE WORK, THE USE OF THE AIR DUSTER PRODUCTS CONTAINING
THE INFLAMMABLE GAS IS PROHIBITED.

Confidential
About This Manual
This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included
herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.
Manual Configuration
This manual consists of six chapters and Appendix.
CHAPTER 1.PRODUCT DESCRIPTIONS
Provides a general overview and specifications of the product.
CHAPTER 2.OPERATING PRINCIPLES
Describes the theory of electrical and mechanical operations of the
product.
CHAPTER 3.TROUBLESHOOTING
Describes the step-by-step procedures for the troubleshooting.
CHAPTER 4.DISASSEMBLY / ASSEMBLY
Describes the step-by-step procedures for disassembling and assembling
the product.
CHAPTER 5.ADJUSTMENT
Provides Epson-approved methods for adjustment.
CHAPTER 6.MAINTENANCE
Provides preventive maintenance procedures and the lists of Epson-
approved lubricants and adhesives required for servicing the product.
CHAPTER 7.APPENDIX
Provides the following additional information for reference:
• Connectors
• ASP List
• Exploded Diagrams
Symbols Used in this Manual
Various symbols are used throughout this manual either to provide additional
information on a specific topic or to warn of possible danger present during a
procedure or an action. Be aware of all symbols when they are used, and always read
NOTE, CAUTION, or WARNING messages.
Indicates an operating or maintenance procedure, practice or condition
that is necessary to keep the product’s quality.
Indicates an operating or maintenance procedure, practice, or condition
that, if not strictly observed, could result in damage to, or destruction of,
equipment.
May indicate an operating or maintenance procedure, practice or
condition that is necessary to accomplish a task efficiently. It may also
provide additional information that is related to a specific subject, or
comment on the results achieved through a previous action.
Indicates an operating or maintenance procedure, practice or condition
that, if not strictly observed, could result in injury or loss of life.
Indicates that a particular task must be carried out according to a certain
standard after disassembly and before re-assembly, otherwise the quality
of the components in question may be adversely affected.

Confidential
Revision Status
Revision Date of Issue Description
A July 18, 2008 First release
B December 12, 2008 Ch1:
1.2.2 Durability (p. 16)
Revised contents.
1.4.2 Panel Settings (p. 24)
Added the ROLL PAPER COUNTER menu.
1.4.3 Maintenance Mode (p. 32)
Added the REMAINING PPR SETUP menu.
1.4.4 Serviceman Mode (p. 33)
Added the menu list.
Ch4:
4.1.3 Recommended Tools (p. 66)
Added Thread-locker.
Ch5:
5.1.4 Tools for Adjustments (p. 191)
Added Thread-locker.
5.1.5 Service Program Basic Operations (p. 192)
Changed the explanation partially.
5.3.3 CR Height Adjustment (p. 204)
Corrected the values indicating the jig’s thickness.
5.4.6 Head Slant and Alignment Adjustment (p. 212)
Changed the explanation.
5.6.1 RTC and USB ID (p. 224)
Changed the explanation.
5.8.3 Electric Components Test (p. 236)
Changed the actions of the F COVER and the M COVER when checking partially.
Ch6:
6.4 Cleaning (p. 246)
Added the Carriage Rail Cleaner and the Carriage Rail Oil to the Maintenance Kit.
6.5 Lubrication (p. 253)
Added the Part No. of grease.

Confidential
B December 12, 2008 Ch7:
7.3 Parts List (p. 262)
Update the information to the latest.
7.4 Exploded Diagram (p. 267)
Update the information to the latest.
C June 5, 2009 Ch3:
3.3 Remedies for Maintenance Requests (p. 54)
Added a table.
3.4 Remedies for Service Call Error (p. 55)
Added the Debug error.
Ch4:
4.1.1 Precautions (p. 64)
Changed the warnings partially.
4.1.3 Recommended Tools (p. 66)
Changed the length of Hexagonal wrench.
4.4.9.6 LOWER BEARING (p. 152)
Added the disassembling/reassembling procedures.
Ch5:
5.1.4 Tools for Adjustments (p. 191)
Added 1000mm Ruler.
5.1.5 Service Program Basic Operations (p. 192)
Changed the name.
5.2 NV-RAM BACKUP UTILITY (p. 198)
Changed the steps of Restore Procedure.
5.8.2 CR Durability Test (p. 235)
Added the section.
Ch6:
6.5 Lubrication (p. 253)
Added the caution.
6.5 Lubrication (p. 253)
Change the name of grease.
6.5 Lubrication (p. 253)
Added the amount of lubricant.
Revision Date of Issue Description

Confidential
D September 18, 2009 Ch1:
Ink set configuration (p. 14)
Added the Ink Set Configuration.
Ch5:
5.3.2 CR Reduction Belt Tension Adjustment (p. 201)
Added the procedure.
E January 15, 2010 Ch4:
4.1.1 Precautions (p. 64)
Changed the cautions partially.
4.4.6.3 MAIN BOARD ASSY (p. 110)
Modified the adjustment.
4.4.11.11 CR CURSOR ASSY (p. 175)
Modified the adjustment.
4.4.9.2 CR REDUCTION BELT (p. 144)
Modified the adjustment.
4.4.9.5 CR MOTOR (p. 151)
Modified the adjustment.
4.4.11.1 PRINT HEAD/VALVE ASSEMBLY, HEAD (p. 158)
Modified the adjustment.
Ch5:
5.1.2 Adjustment Items and the Order by Repaired Part (p. 186)
Changes partially.
5.6.4.1 IP Address Setup (p. 228)
Added the adjustment.
5.6.4.2 Network Test (p. 228)
Changed.
5.6.5 NVRAM CLEAR OK (p. 229)
Added the adjustment.
5.6.6 Rear Sensor Test/Rear AD Adjustment (p. 230)
Added the adjustment.
5.6.7 Input Serial Number (p. 231)
Added the adjustment.
5.6.8 CR Origin Adjustment (p. 232)
Added the adjustment.
5.3.2 CR Reduction Belt Tension Adjustment (p. 201)
Changed the procedure. Added the Video. (Chapter 8)
Revision Date of Issue Description

Confidential
F December 12, 2011 Ch5:
5.3.3 CR Height Adjustment (p. 204)
Change the Figure 5-20.
Ch5:
6.5 Lubrication (p. 253)
Change Grease type.
Revision Date of Issue Description

Epson Stylus Pro GS6000 Revision F
9
Confidential
Contents
Chapter 1 PRODUCT DESCRIPTION
1.1 Features ............................................................................................................... 12
1.2 Basic Specifications ............................................................................................ 13
1.2.1 Printer Specifications ................................................................................. 13
1.2.2 Durability ................................................................................................... 16
1.2.3 Paper size/Printable area ............................................................................ 16
1.2.4 Print Mode / Print Resolution .................................................................... 17
1.3 Dimensions and Main Components .................................................................... 18
1.3.1 Dimensions and Weight ............................................................................. 18
1.3.2 Part Names ................................................................................................. 19
1.4 Control Panel ...................................................................................................... 20
1.4.1 Buttons and Indicators ............................................................................... 20
1.4.2 Panel Settings ............................................................................................. 24
1.4.3 Maintenance Mode .................................................................................... 32
1.4.4 Serviceman Mode ...................................................................................... 33
Chapter 2 OPERATING PRINCIPLES
2.1 Glossary .............................................................................................................. 41
2.2 Ink System .......................................................................................................... 42
2.3 Carriage Mechanism ........................................................................................... 43
2.4 Paper Feed Mechanism ....................................................................................... 44
2.5 Heater Mechanism .............................................................................................. 45
2.6 Boards ................................................................................................................. 46
2.7 Sensors ................................................................................................................ 47
2.8 Fans ..................................................................................................................... 48
Chapter 3 TROUBLE SHOOTING
3.1 Overview ............................................................................................................ 50
3.1.1 Preliminary Check ..................................................................................... 50
3.1.2 Troubleshooting Procedure ........................................................................ 50
3.2 Remedies for Error Messages ............................................................................. 51
3.3 Remedies for Maintenance Requests ................................................................. 54
3.4 Remedies for Service Call Error ........................................................................ 55
3.5 Remedies for Print Quality Troubles .................................................................. 60
Chapter 4 DISASSEMBLY & ASSEMBLY
4.1 Overview ............................................................................................................ 64
4.1.1 Precautions ................................................................................................. 64
4.1.2 Orientation Definition ................................................................................ 66
4.1.3 Recommended Tools ................................................................................. 66
4.2 Parts Diagram ..................................................................................................... 67
4.3 Disassembly Flowchart ...................................................................................... 76
4.4 Disassembly and Assembly Procedure ............................................................... 83
4.4.1 Basic Operations ........................................................................................ 83
4.4.2 Consumables/Accessories ......................................................................... 84
4.4.3 Housing ...................................................................................................... 85
4.4.4 Electric Components .................................................................................. 99
4.4.5 Fans .......................................................................................................... 101
4.4.6 Boards ...................................................................................................... 109
4.4.7 Sensors ..................................................................................................... 123
4.4.8 Heaters/Thermistors ................................................................................. 137
4.4.9 Carriage Mechanism ................................................................................ 142
4.4.10 Paper Feed Mechanism .......................................................................... 155
4.4.11 Ink System Mechanism ......................................................................... 158
4.4.12 Take-Up Reel Unit ................................................................................. 177
Chapter 5 ADJUSTMENT
5.1 Overview .......................................................................................................... 185
5.1.1 Precautions ............................................................................................... 185
5.1.2 Adjustment Items and the Order by Repaired Part .................................. 186

Epson Stylus Pro GS6000 Revision F
10
Confidential
5.1.3 Description of Adjustments ..................................................................... 189
5.1.4 Tools for Adjustments ............................................................................. 191
5.1.5 Service Program Basic Operations .......................................................... 192
5.1.6 Cautions and Preparation for Pattern Printing ......................................... 197
5.2 NV-RAM BACKUP UTILITY ........................................................................ 198
5.3 CR Related Adjustments .................................................................................. 199
5.3.1 CR Belt Tension Adjustment ................................................................... 199
5.3.2 CR Reduction Belt Tension Adjustment ................................................. 201
5.3.3 CR Height Adjustment ............................................................................ 204
5.3.4 Media Side Margin Adjustment ............................................................... 206
5.4 Head Related Adjustments ............................................................................... 207
5.4.1 Head Rank Input ...................................................................................... 207
5.4.2 Nozzle Check Pattern .............................................................................. 208
5.4.3 Cleaning and Washing ............................................................................. 209
5.4.4 Ink Discharge ........................................................................................... 210
5.4.5 Initial Ink Charge Flag ............................................................................. 211
5.4.6 Head Slant and Alignment Adjustment ................................................... 212
5.4.7 Head Nozzles Alignment Adjustment ..................................................... 218
5.4.8 Head Uni-D/Bi-D Low Gap Adjustment ................................................. 219
5.5 PF Related Adjustments ................................................................................... 222
5.5.1 PF Reduction Belt Tension Adjustment .................................................. 222
5.5.2 Paper Feed Adjustment ............................................................................ 223
5.6 Other Adjustments ............................................................................................ 224
5.6.1 RTC and USB ID ..................................................................................... 224
5.6.2 Firmware Update ..................................................................................... 225
5.6.3 Washing Sequence Flag ........................................................................... 227
5.6.4 IP Address Setup & Network Test ........................................................... 228
5.6.5 NVRAM CLEAR OK .............................................................................. 229
5.6.6 Rear Sensor Test/Rear AD Adjustment ................................................... 230
5.6.7 Input Serial Number ................................................................................ 231
5.6.8 CR Origin Adjustment ............................................................................. 232
5.7 Clear Counters .................................................................................................. 233
5.8 Tests .................................................................................................................. 234
5.8.1 Skew Test ................................................................................................. 234
5.8.2 CR Durability Test ................................................................................... 235
5.8.3 Electric Components Test ........................................................................ 236
Chapter 6 MAINTENANCE
6.1 Overview .......................................................................................................... 241
6.2 Setting up and Transportation .......................................................................... 242
6.2.1 Setting up ................................................................................................. 242
6.2.2 Transportation .......................................................................................... 243
6.3 Maintenance ..................................................................................................... 244
6.4 Cleaning ............................................................................................................ 246
6.4.1 Cleaning Wiper ........................................................................................ 247
6.4.2 Around the Print head .............................................................................. 249
6.4.3 Cleaning the Pressure Rollers and Platen ................................................ 250
6.4.4 Cleaning and Lubricating the CR rail ...................................................... 252
6.5 Lubrication ....................................................................................................... 253
Chapter 7 APPENDIX
7.1 Block Wiring Diagram ..................................................................................... 258
7.2 Panel Menu Map .............................................................................................. 259
7.3 Parts List ........................................................................................................... 262
7.4 Exploded Diagram ............................................................................................ 267

Confidential
CHAPTER
1
PRODUCTDESCRIPTION

Epson Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Features 12
Confidential
1.1 Features
Epson Stylus Pro GS6000 is a wide-format color Eco-Solvent ink jet printer that
supports 64-inch roll paper. The features of this printer are;
High-speed output
The new type print head achieves high-speed output. It is compatible with paper
up to 1,625 mm in width.
Wide variety of compatible paper
The head is adjustable to two levels of height and compatible with paper up to
1.3 mm in thickness.
Vibrant color reproduction
Eight colors of ink are used for printing in order to reproduce sharp and vivid
colors. This printer uses 950 ml large-capacity ink cartridges. Use of variable dots
can improve color reproduction.
Multi-heater
Heaters are installed at three locations (pre, platen, after) allowing solvent ink to
fix better on paper and dry quickly.
Auto Take-Up Reel Unit
This automatically takes up printed paper, keeping it clean and free of creases. It is
also convenient for storage and transportation.
Large-capacity (950 ml) ink cartridge
Epson provides the large-capacity (950 ml) ink cartridges for this printer that
realize the high productivity required for professional work.
High speed USB 2.0 / Gigabit Ethernet
You can connect to a high-speed network (such as USB 2.0 or Ethernet 100/1000)
and that improves the file transfer speed.
Active indicator
The Active indicator flashes when an error has occurred during operation. Since
the indicator is big, customers can easily check the operational status of the printer
at a distance.
Figure 1-1. External View

Epson Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Basic Specifications 13
Confidential
1.2 Basic Specifications
1.2.1 Printer Specifications
Note *1: Each color has two lines.
ELECTRIC SPECIFICATIONS
Item Specification
Printing method On-demand ink jet
Nozzle configuration
Black: 180 nozzles per color x 2*1
Color: 180 nozzles per color x 2*1
(Cyan, Magenta, Light Cyan, Light
Magenta, Yellow, Green, Orange)
Character mode Character Pitch 10 cpi
Printing Column 635
Raster graphic mode
Horizontal resolution 540 dpi 720 dpi 1440 dpi
Printable width 1615.0 mm (63.58")
Available dots 34,334 45,779 91,559
Resolution Maximum 1440 x 1440 dpi
Print direction Bidirectional
Control code ESC/P Raster, ESC/P2
RAM 256 MB (MAIN) + 64 MB (Network)
Character tables PC 437 (US, Standard Europe)
Character sets EPSON Courier 10 cpi
Paper feed method Friction
Paper path Roll paper
Item Specification
100-120V Model 220-240V Model
Rated voltage AC 100 to 240 V
Input voltage range AC 90 to 264 V
Rated frequency range 50 to 60 Hz
Input frequency range 49 to 61 Hz
Rated current
MAIN 11 A 6 A
HEATER 11 A 6 A
TAKE-UP REEL 0.4A 0.4 A
Power consumption
(MAIN + HEATER)
Printing Approx. 680 W
Ready
mode
Idle heat
ON Approx. 680 W
Idle heat
OFF Approx 48 W Approx 40 W
Sleep mode Approx. 24 W
Power off: Approx. 3 W

EPSON Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Basic Specifications 14
Confidential
INK CARTRIDGES INK SET CONFIGURATION
Ink Set Configuration
Note : 1-row starting from the left facing the front of the printer.
Nozzle Configuration
LEFT HEAD:
Note : 1-row starting from the left facing the front of the printer.
RIGHT HEAD:
Note : 1-row starting from the left facing the front of the printer.
ENVIRONMENTAL CONDITIONS
Note *: Without condensation
Item Specification
Colors
Cyan
Magenta
Yellow
Black
Light Cyan
Light Magenta
Green
Orange
Cartridge life See expiry date on package or cartridge.
Within 6 months after opening package.
Temperature
Storage
(uninstalled) -20 to 40°C (-4 to 104°F)
1 month at 40°C (104°F)
Storage
(installed) -10 to 40°C (14 to 104°F)
4 days at 32°C (90°F)
Capacity 950 ml
Dimensions 53.1 mm (W) x 316.1 mm (D) x 146.2 mm (H)
Ink Type 1-row 2-row 3-row 4-row 5-row 6-row 7-row 8-row
Pigment Or Gr Lm Lc K Y M C
Ink Type 1-row 2-row 3-row 4-row 5-row 6-row 7-row 8-row
PigmentMMCCKKYY
Ink Type 1-row 2-row 3-row 4-row 5-row 6-row 7-row 8-row
PigmentOrOrGrGrLcLcLmLm
Item Specification
Temperature
Operation 20 to 32°C (68 to 89.6°F)
Print Quality Guarantee 22 to 32°C (72 to 89.6°F)
Storage -10 to 40°C (14 to 104°F)
4 days at 32°C (90°F)
Humidity
Operation 40 to 60% RH*
Print Quality Guarantee 40 to 60% RH*
Storage 20 to 80% RH*

EPSON Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Basic Specifications 15
Confidential
ROLL PAPER
STANDARDS AND APPROVALS
MECHANISM
Item Specification
Paper size (width) 300 mm (12") to 1625 mm (64")
Internal diameter 3 inches
Outer diameter Max. 170 mm (6.7")
Thickness
When Head height
adjustment lever is Low Max 0.3 mm
When Head height
adjustment lever is High Max 1.3 mm
Weight Max. 30 kg
Item Specification
Safety
UL 60950-1
CSA No. 60950-1
Low Voltage Directive
2006/95/EC EN 60950-1
EMC
FCC part 15 subpart B class A
CAN/CSA-CEI/IEC CISPR 22 Class A
AS/NZS CISPR 22 Class A
EMC Directive
2004/108/EC
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
Item Specification
CR and PF drive method Servo motor and DC motor are operated by the firmware
Paper feed method Loads paper at the rear and ejects paper to the front
Print Head 180 nozzles x 8 rows
Two Print Heads are mounted.
Ink
Ink supply
method Ink is supplied from the independent ink cartridges through a tubes via the sub tanks.
Ink type Eco-Solvent ink
Ink colors Black, Cyan, Magenta, Yellow, Light Cyan,
Light Magenta, Green, Orange
Waste ink tank
Attachment Secured to the main unit
Capacity 2,000 ml
Full tank
detection Detected by the float sensor
Noise 50dB or lower
Take-Up Reel
Unit Drive method Driven by DC geared motor

EPSON Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Basic Specifications 16
Confidential
1.2.2 Durability
The following lists the parts that need periodical replacement as indicated.
1.2.3 Paper size/Printable area
SUPPORTED PAPER SIZE/THICKNESS
The supported paper size and thickness are described below.
Figure 1-2. Supported Paper Size
Item Durability Panel message display
Head Caps 1 year None
Wiper 1 year None
Head & Dumpers 6,000,000,000 dots/nozzle None
CR Motor 6,220,000 passes Indicated
PF Motor 30,000 m. None
Item Value
Width 300 to 1625 mm
Thickness When Head height adjustment lever is Low Max 0.3 mm
When Head height adjustment lever is High Max 1.3 mm
300mm
1625mm

EPSON Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Basic Specifications 17
Confidential
PRINTABLE AREA
The printable area of this printer is described below.
Figure 1-3. Printable Area
1.2.4 Print Mode / Print Resolution
The table below lists the print mode and the resolution.
Item Value
AMin. 5 mm
B-L 5 to 25 mm
B-R 5 to 25 mm
C Min. 5 mm When end of the roll paper, the margin will be 77.4 mm.
Unit: mm
C
B-R
B-L
A
Feed direction
Media
Type Print quality Print density (HxV) Dot size Pass (CRxPF) Uni/Bi Throughput (m2/h)
Marking
Film
Max
Quality 1440x1440dpi VSD3d-S(320cps) 4x4 pass Uni-D 1.6
Bi-D 2.9
Quality
11440x720dpi VSD3d-V(320cps) 4x2 pass Uni-D 3.3
Bi-D 5.8
Quality
2720x720dpi VSD3d-V(400cps) 4x2 pass Uni-D 3.6
Bi-D 7.0
Quality
3540x720dpi VSD3d-V(400cps) 3x2 pass Uni-D 5.5
Bi-D 9.3
Banner
Speed 1 540x720dpi VSD1d-V(400cps) 3x2 pass Uni-D 5.5
Bi-D 9.3
Speed 2 720x720dpi VSD1d-V(400cps) 2x2 pass Uni-D 8.3
Bi-D 13.6
Speed 3 720x360dpi VSD1d-L(400cps) 2x1 pass Uni-D 16.6
Bi-D 25.3

EPSON Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Dimensions and Main Components 18
Confidential
1.3 Dimensions and Main Components
This section describes the printer dimensions and the main components.
1.3.1 Dimensions and Weight
Figure 1-4. Printer Dimensions (standard)
Dimensions
Standard (with the Auto Take-up Reel Unit):
2,698 (W) x 1,045 (D) x 1,267 (H) mm
Without the Auto Take-up Reel Unit:
2,698 (W) x 943 (D) x 1,267 (H) mm
Weight
Printer main body and the Stand (excludes the ink cartridges and paper):
Approx. 183 kg
Printer main body only (excludes the ink cartridges and paper):
Approx. 150 kg
Auto Take-up Reel unit: Approx. 19 kg
1,045 mm
2,698 mm
1,267 mm

Epson Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Dimensions and Main Components 19
Confidential
1.3.2 Part Names
FRONT
Figure 1-5. Part Name (Front)
REAR
Figure 1-6. Part Name (Rear)
Pressure Rollers Front Cover
Platen
Paper holder plate
Maintenance
Cover
Paper Guide
Front Cover
Paper Holder Plate
Active Indicator
Stand
Adjuster
AC inlet
Adjuster
Stand
Ink drain tank
Paper lever
Maintenance
Cover
Control panel
Paper Guide
Paper Feed Slot
Ink Cartridge
Compartment
Roll Paper Holders
Network Interface Connector
USB Interface Connector
Waste Ink Valve
Roll Paper Holders
Ink Cartridge
Compartment

EPSON Stylus Pro GS6000 Revision F
PRODUCT DESCRIPTION Control Panel 20
Confidential
1.4 Control Panel
1.4.1 Buttons and Indicators
BUTTONS
Figure 1-7. Buttons
Note *1: When AUTO TAKE-UP REEL is ON in the Menu mode, the roll paper cannot be
fed in the reverse direction.
[Pause/Reset]
button
b
a
[Heater]
button
c
[Enter]
button
d
[Low Heat]
button
g
[HighHeat]
button
h
[Power] button [Paper Feed]
button
e
[Paper Feed]
button
e
[Menu]
button
f
Button Name Function
a[Power] Turns the printer on or off.
b[Pause/Reset]
Stops printing temporarily, or restarts printing if pressed when the
printer is in the pause mode.
Clears print data in the printer memory if pressed and held for
3 seconds.
The printer returns to the READY state when this button is
pressed in the Menu mode.
c[Heater]
Selects a heater type. From the right, Pre Heater, Platen Heater,
and After Heater are displayed on the LCD panel. Select a heater
type, and then press the [High Heat] button or [Low Heat] button
to change the preset temperature.
Returns to the previous level when pressed in the Menu mode.
d[Enter]
Sets the selected parameter in the selected item in the Menu mode.
Executes the item if the selected item is for execution only.
e[Paper Feed]
Feeds the roll paper in the forward or reverse direction.*1
Changes the parameter in the forward or reverse order when
selecting a desired parameter in the Menu mode.
The numeric value is decreased or increased during numerical
input.
f [Menu]
Enters the Menu mode when pressed in the READY state.
Enters the Printer Status menu if pressed during printing.
Stops printing temporarily, or restarts When pressed in the Menu
mode, a desired menu can be selected.
Performs Cleaning (Light) to clean the print heads if pressed and
held for 3 seconds.
g [Low Heat] Decreases the preset temperature of the heater. You can also
change the preset temperature while printing.
h[High Heat] Increases the preset temperature of the heater. You can also
change the preset temperature while printing.