Epson SureColor T5270D User manual

Setup Guide
Guía de instalación
Guia de instalação
Printed in USA
Impreso en EE.UU.
Impresso nos E.U.A.
CPD-41579
Epson®SureColor®T-Series
Epson®SureColor®T-Series

Control panel
Panel de control
Painel de controle
Back button
Botón de volver
Botão voltar
Menu button
Botón Menu
Botão Menu
Load/remove paper button
Botón de carga/retiro de papel
Botão de carregamento/expulsão de papel
Power button and light
Botón e indicador de encendido
Botão e luz de energia
Pause/cancel button
Botón de pausa/cancelar
Botão de pausar/cancelar
Maintenance button
Botón de mantenimiento
Botão de manutenção
Media feed button
Botón de alimentación del papel
Botão de alimentação de papel
LCD display
Pantalla LCD
Visor LCD
Help button
Botón de ayuda
Botão de ajuda

English
Contents
Unpacking and Assembling the Printer ..................................................................................................3
Setting up the SureColor T3270/T5270/T7270 ....................................................................................5
Setting up the SureColor T5270D/T7270D ........................................................................................15
Connecting the Power Cord ................................................................................................................24
Installing Ink Cartridges ......................................................................................................................25
Loading Roll Paper ..............................................................................................................................26
Loading Roll Paper into the Secondary Roll Unit ................................................................................32
Performing a Test Print .......................................................................................................................36
Aligning the Print Head .......................................................................................................................36
Installing Software ...............................................................................................................................37
Updating Your Printer Firmware .........................................................................................................37
T-Series_Setup_Guide_S.book Page 1 Tuesday, September 16, 2014 2:53 PM

2|
T-Series_Setup_Guide_S.book Page 2 Tuesday, September 16, 2014 2:53 PM

Unpacking and Assembling the Printer |3
Unpacking and Assembling the Printer
Note: Unless otherwise indicated, the illustrations in this manual show the Epson®SureColor®T7270, but the
instructions apply to all five models.
Before beginning assembly, make sure you have sufficient space to set up and use the printer. The
following illustrations show the minimum space required for using the printer:
SureColor T3270/T5270/T7270 SureColor T5270D/T7270D
When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations
subject to direct sunlight, excessive heat, humidity, or dust. Be sure the printer is placed on a flat, stable
location that can support the following weight for each printer:
•SureColor T3270 —148 lb (67 kg)
•SureColor T5270 —185 lb (84 kg)
•SureColor T7270 —203 lb (92 kg)
•SureColor T5270D —260 lb (118 kg)
•SureColor T7270D — 293 lb (133 kg)
WARNING: Two people are required to unpack and install the SureColor T3270 printer; four people are required
to unpack and install the SureColor T5270, T5270D, T7270, and T7270D printers.
You need an even larger floor space to assemble the printer and stand, so be sure to prepare a large, clear
area before unpacking them. Also make sure you save the box and packaging in case you need to ship the
printer later.
5.9 in. (150 mm)
0.39 in.
(10 mm)
23.6 in.
(600 mm) 5.9 in. (150 mm) 5.9 in. (150 mm)
19.7 in.
(500 mm)
5.9 in. (150 mm)
0.39 in.
(10 mm) 3.9 in.
(100 mm)
T-Series_Setup_Guide_S.book Page 3 Tuesday, September 16, 2014 2:53 PM

4|Unpacking and Assembling the Printer
The following items are included with your printer:
SureColor T3270/T5270/T7270
Note: For information on the optional hard disk and the Take-up Reel, see the online User’s Guide.
4
6
2
2
AB
10
C
× 4 (T7270)
× 3 (T5270)
× 2 (T3270)
× 5 (T7270)
× 4 (T5270)
× 3 (T3270)
T-Series_Setup_Guide_S.book Page 4 Tuesday, September 16, 2014 2:53 PM

Setting up the SureColor T3270/T5270/T7270 |5
SureColor T5270D/T7270D
Setting up the SureColor T3270/T5270/T7270
Assembling the Stand
1. Unpack the stand and make sure you have all of these items.
L
12
4
A
B
T-Series_Setup_Guide_S.book Page 5 Tuesday, September 16, 2014 2:53 PM

6|Assembling the Stand
2. Slide the horizontal strut into both of the legs.
3. Use the long end of the hex wrench to tighten the pre-placed screws on each side of the horizontal
strut.
4. Lock the casters to fix the stand in place. (When moving the printer, unlock the casters.)
T-Series_Setup_Guide_S.book Page 6 Tuesday, September 16, 2014 2:53 PM

Mounting the Printer on the Stand |7
Mounting the Printer on the Stand
You need at least two people (SureColor T3270) or four people (SureColor T5270/T7270) to install the
printer and position it on the stand. When lifting the printer, only hold the areas shown below. Otherwise,
damage may occur.
Caution: Before installing the printer, lock the casters to make sure the stand is fixed in place.
1. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the
top of the stand legs before setting the printer down.
SureColor T3270
SureColor T5270/T7270
T-Series_Setup_Guide_S.book Page 7 Tuesday, September 16, 2014 2:53 PM

8|Attaching the Paper Basket
2. Attach the printer to the stand using three bolts.
Attaching the Paper Basket
The paper basket is a cloth sheet that attaches to the printer stand and catches your prints as they come
out. You need the following parts to assemble and attach the paper basket:
1. Attach the stabilizers.
10 6
ABC
2
× 4 (T7270)
× 3 (T5270)
× 2 (T3270)
× 5 (T7270)
× 4 (T5270)
× 3 (T3270)
× 5 (T7270)
× 4 (T5270)
× 3 (T3270)
T-Series_Setup_Guide_S.book Page 8 Tuesday, September 16, 2014 2:53 PM

Attaching the Paper Basket |9
2. Insert the end of one of the shorter square poles into one of the plastic connectors.
3. Slide the pole through the holes in the stabilizers and attach a plastic connector to the other end of the
pole. Then, fasten the plastic connectors in place on each side of the stand.
4. Attach the stack guides to the bottom of the printer. Make sure each guide snaps securely into place.
× 4 (T7270)
× 3 (T5270)
× 2 (T3270)
T-Series_Setup_Guide_S.book Page 9 Tuesday, September 16, 2014 2:53 PM

10 |Attaching the Paper Basket
5. Insert the end of the other short square pole into one of the plastic connectors.
6. Slide the pole through the holes in the stack guides and attach a plastic connector to the other end of
the pole. Then, fasten the plastic connectors in place on each side of the stand.
7. Insert the two longer square poles into the right basket arm.
C
T-Series_Setup_Guide_S.book Page 10 Tuesday, September 16, 2014 2:53 PM

Attaching the Paper Basket |11
8. Thread both poles through the paper basket.
9. Insert the ends of the poles into the left basket arm.
10. Attach the two basket holders, one on each side of the stand. Use four bolts to fasten the holders in
place.
L
T-Series_Setup_Guide_S.book Page 11 Tuesday, September 16, 2014 2:53 PM

12 |Attaching the Paper Basket
11. Insert a nut into the center bolt hole on the basket holder, and align the right basket arm with the bolt
hole.
12. Insert the bolt sleeve through the basket arm and into the bolt hole. Insert the bolt into the bolt sleeve
and tighten it. Repeat steps 11 and 12 on the left side of the printer.
13. Attach the shorter arm to the inside of the basket holder on the left side of the printer. Use two nuts to
hold the arm in place.
T-Series_Setup_Guide_S.book Page 12 Tuesday, September 16, 2014 2:53 PM

Attaching the Paper Basket |13
14. Use two bolts to fasten the arm in place.
15. Insert the longer arm into the round pole.
16. Insert the end of the round pole into the arm on the left side of the printer. Then, align the right
basket arm with the mounting holes on the right basket holder.
T-Series_Setup_Guide_S.book Page 13 Tuesday, September 16, 2014 2:53 PM

14 |Attaching the Paper Basket
17. Use two nuts and two bolts to fasten the arm in place.
18. Flip the loose end of the basket cloth over the top rail and feed it towards the back of the printer.
19. On the back side of the printer, pull the paper basket up so that the stack guides fit into the slots as
shown. Then, hook the loops around the pins on the back of the stack guides to hold the basket in
place.
T-Series_Setup_Guide_S.book Page 14 Tuesday, September 16, 2014 2:53 PM

Setting up the SureColor T5270D/T7270D |15
20. Hook the loops on the sides of the basket to the pins on the back of the stand legs to secure the basket
to the printer.
21. On the front side of the printer, slide the basket fabric all the way to the ends of the pole.
Setting up the SureColor T5270D/T7270D
Assembling the Stand
1. Unpack the stand and make sure you have all of these items.
T-Series_Setup_Guide_S.book Page 15 Tuesday, September 16, 2014 2:53 PM

16 |Assembling the Stand
2. Slide the horizontal strut into both of the legs.
3. Use the long end of the hex wrench to tighten the pre-placed screws on each side of the horizontal
strut.
4. Lock the casters to fix the stand in place. (When moving the printer, unlock the casters.)
T-Series_Setup_Guide_S.book Page 16 Tuesday, September 16, 2014 2:53 PM

Mounting the Second Paper Roll |17
Mounting the Second Paper Roll
1. Unpack the roll unit and make sure you have all of these items.
2. Secure the roll supports to the legs of the stand using four bolts per support.
3. Remove the tape from the mounting brackets and extend the left and right rail until you hear a click.
B
12
B8
T-Series_Setup_Guide_S.book Page 17 Tuesday, September 16, 2014 2:53 PM

18 |Mounting the Second Paper Roll
4. Carefully place the second roll unit on the extended rails.
Caution: Placing the unit requires two people.
5. Secure the unit to the rails with two bolts on each side.
B4
T-Series_Setup_Guide_S.book Page 18 Tuesday, September 16, 2014 2:53 PM